Page 1
• INSTALLATION MANUAL Always read this manual first before attempting to install or use the NetZero firebox. For your safety, always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage. To view the full line of NetZero products, please visit www.netzerofire.com...
Table of Contents 1 IMPORTANT INFORMATION............................3 Safety Information ............................3 FIREBOX INSTALLATION ............................4 2.1 Considerations: ............................... 4 2.2 Preparing for Installation ............................4 2.3 Included Parts ................................. 4 2.3.1 Single-Sided, Right-Corner, Left-Corner, and Three-Sided Firebox ..............4 2.3.2 See-Through and Peninsula Firebox ........................ 4 2.4 Configuring the Firebox for Installation ........................
1 IMPORTANT INFORMATION 1.1 Safety Information Always use a qualified technician or service agency to repair this unit. CAUTION: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock, fire hazard and will void the warranty. When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: Read all instructions before using the unit.
2 FIREBOX INSTALLATION 2.1 Considerations: • Accessibility to electricity and 1/4’’ water line, like ice maker in fridge. • Recessed into wall, sitting proud of a wall or completely free-standing? • If light cast upwards to ceiling is undesirable, consider recessing into the wall for a traditional hearth appearance.
2.4 Configuring the Firebox for Installation The NetZero Firebox can be installed in the following configurations. The firebox is ordered as a single-sided or see- through firebox. The single-sided firebox can be configured into a left-corner, right-corner, or three-sided firebox by removing one or both sides.
2.5 Framing IMPORTANT: The framing above the firebox must be self-supporting. The firebox is not load-bearing. - The firebox must be installed on a level surface capable of supporting the firebox, burner, and full fuel capacity. NOTE: Dimension W2 in the tables below must be wide enough to support the side flanges of the firebox.
2.5.2 Left-Corner or Right-Corner Installation Construct the main wall framework with the opening size shown in Table B. D1 max H1 min Firebox (in) (in) (in) (in) (in) (in) (in) Left/Right-Corner NZW36F 26-32 Left/Right-Corner NZW48F 38-44 17 1/2 27 1/2 Left/Right-Corner NZW72F 62-68 Table B...
2.5.3 Three-Sided Installation Construct the main wall framework with the opening size shown in Table C. W1 min W2 max D1 max H1 min Firebox (in) (in) (in) (in) (in) (in) (in) Three-Sided NZ36F Three-Sided NZ48F 17 1/2 27 1/2 Three-Sided NZ72F Table C...
2.5.4 See-Through Installation Construct the main wall framework with the opening size shown in Table D. D1 max H1 min Firebox (in) (in) (in) (in) (in) (in) (in) See-Through NZ48F 40-46 27 1/2 See-Through NZ72F 64-70 Table D...
2.5.5 Peninsula Installation Construct the main wall framework with the opening size shown in Table E. D1 max H1 min Firebox (in) (in) (in) (in) (in) (in) (in) Peninsula NZ48F 38-44 27 1/2 Peninsula NZ72F 62-68 Table E...
2.6 Firebox Installation WARNING: Do not modify the firebox in any way during installation. Cutting of sheet metal parts of the firebox is prohibited. NOTE: Framing may look different based on configuration, the same steps still apply. a) Slide the firebox into the framing cavity. The firebox is shipped with stability bracket(s) installed on the open side(s) to keep the firebox square while in transport and during installation.
2.7 Installing Finishing Material 2.7.1 Optional Finishing Guides The firebox comes with optional finishing guides. These guides install to the front face of the firebox. They provide an edge that can be finished up to with finishing material and will then cover the cut edge of the finishing material. The guides protrude 1/2 inch from the face of the firebox.
2.8 Installing Optional Light Deflector The optional light deflector can be installed to the top in the center of the firebox by sticking the adhesive backing to the top. The light deflector will reflect the light back onto the floor to illuminate the top of the logs or media. 3 Electrical Connection 3.1 AC Power Connection Burners must be connected to a dedicated 120 volt/60 Hz –...
If your fireplace is being connected to a water supply line, connect the water supply line before placing the burner into the enclosure. c) Lift the burner and place it into the firebox. 4.2 Burner Specifications Table A Approx. run NetZero NetZero Fuel Capacity Burner Length Burner Width Burner Height...
Need help?
Do you have a question about the Firebox Series and is the answer not in the manual?
Questions and answers