thomann the t.racks SRL-4 Quick Start Manual

SRL-4 Solid Rack Light RGBW
Safety instructions
Intended use
This device is intended for the temporary illumination of racks by means of LED tech-
nology. Any other use or use under other operating conditions is considered to be
improper and may result in personal injury or property damage. No liability will be
assumed for damage resulting from improper use.
This device may be used only by persons with sufficient physical, sensory, and intel-
lectual abilities and the necessary knowledge and experience. Other persons may use
this device only if they are supervised or instructed by a person who is responsible
for their safety.
Extend the operating life of the device by means of regular pauses in opera-
tion and by avoiding frequent switching on and off. The device is not suitable
for continuous operation.
Risk of injury and choking hazard for children!
Children can suffocate on packaging material and small parts. Children can
injure themselves when handling the device. Never allow children to play
with the packaging material and the device. Always store packaging mate-
rial out of the reach of babies and small children. Always dispose of pack-
aging material properly when it is not in use. Never allow children to use
the device without supervision. Keep small parts away from children and
make sure that the device does not shed any small parts (such as knobs)
that children could play with.
Risk of death from electrical current!
The device contains parts where high voltage is present. Never remove any
covers! There are no user-serviceable parts inside the device. Do not use
the device if covers, safety equipment or optical components are missing
or damaged.
Risk of death from electrical current!
A short circuit can cause fires and loss of life. Always use a properly insulat-
ed two-core mains cable. Do not modify the mains cable or the power
plug. If the insulation is damaged, immediately switch off the power sup-
ply and have it repaired. If in doubt, contact a qualified electrician.
Risk of eye damage caused by high light intensity!
The device generates high-intensity light radiation. Looking directly into
the light source can damage the eyes. Never look directly into the light
source.
Risk of fire due to covered vents and neighbouring heat sources!
If the vents of the device are covered or the device is operated in the imme-
diate vicinity of other heat sources, the device can overheat and burst into
flames. Never cover the device or the vents. Do not install the device in the
immediate vicinity of other heat sources. Never operate the device in the
immediate vicinity of naked flames.
Features
• Multicolour rack light for even illumination of the rack
• 19" rack-mountable (1 RU)
• 15 selectable macros with different shades of colour and white
• Three selectable brightness levels
Quick start guide
This document contains important information on the safe use of the product.
Read and follow the safety instructions and all other instructions. Keep the docu-
ment for future reference. If you pass the product on to others, please include this
document.
Contents are subject to change. Please refer to the latest version of the documenta-
tion, which is available for download at www.thomann.de.
Damage to the device if operated in unsuitable ambient conditions!
The device can be damaged if it is operated in unsuitable ambient condi-
tions. Only operate the device indoors within the ambient conditions
specified in the "Technical specifications". Avoid operating it in environ-
ments with direct sunlight, heavy dirt and strong vibrations. Avoid operat-
ing it in environments with strong temperature fluctuations. If tempera-
ture fluctuations cannot be avoided (for example after transport in low
outside temperatures), do not switch on the device immediately. Never
subject the device to liquids or moisture. Never move the device to anoth-
er location while it is in operation. In environments with increased dirt
levels (for example due to dust, smoke, nicotine or mist): Have the device
cleaned by qualified specialists at regular intervals to prevent damage due
to overheating and other malfunctions.
Damage to the external power supply due to high voltages!
The device is powered by an external power supply. The external power
supply can be damaged if it is operated with the incorrect voltage or if
high voltage peaks occur. In the worst case, excess voltages can also cause
a risk of injury and fires. Make sure that the voltage specification on the
external power supply matches the local power grid before plugging in
the power supply. Only operate the external power supply from profes-
sionally installed mains sockets that are protected by a residual current
circuit breaker (FI). Ensure that the power cord plug is easily accessible at
all times if it is the only device to safely disconnect the device from the
mains supply. As a precaution, disconnect the power supply from the pow-
er grid when storms are approaching or if the device will not be used for a
longer period.
General handling
• To prevent damage, never exert force while operating the device.
• Never immerse the device in water. Wipe only with a clean and dry cloth. Do not
use liquid cleaners such as benzene, thinners or flammable cleaning agents
• For technological reasons, the light output of LEDs decreases over their lifetime.
This effect increases with higher operating temperatures. You can extend the
service life of the light sources by providing adequate ventilation and operating
the LEDs with the lowest possible brightness.
Keep foreign substances away from the device!
Keep the device away containers with liquid. Should liquid enter the device, this
could lead to its destruction or fire. Ensure that no metallic parts enter the device.
• Memory function
• Sturdy metal design
• Including power adapter
• Strain relief for the power adapter
EN