Liberty Digitalinx Series User Manual
Hdmi 2.0 uncompressed 100m extension set
Hide thumbs
Also See for Digitalinx Series:
- Owner's manual (12 pages) ,
- User manual (9 pages) ,
- User manual (7 pages)
Table of Contents
Advertisement
Quick Links
USER MANUAL
DL-HDE100-H3 Owners Manual
Digitalinx Series HDMI 2.0 Uncompressed 100m Extension Set
18G HDBaseT 3.0 Extender set extends uncompressed resolutions up to 4K60 4:4:4,
IR,RS232,Power, and Gigabit ethernet up to 100m with built in test pattern generator
and adjustable bandwidth mode for maximum cable compatibility
www.libav.com 800.530.8998
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Liberty Digitalinx Series
Summary of Contents for Liberty Digitalinx Series
- Page 1 USER MANUAL DL-HDE100-H3 Owners Manual Digitalinx Series HDMI 2.0 Uncompressed 100m Extension Set 18G HDBaseT 3.0 Extender set extends uncompressed resolutions up to 4K60 4:4:4, IR,RS232,Power, and Gigabit ethernet up to 100m with built in test pattern generator and adjustable bandwidth mode for maximum cable compatibility...
-
Page 2: Product Overview
PRODUCT OVERVIEW Gigabit The Digitalinx DL-HD100-H3 HDBaseT 3.0 extender set transmits video, audio, IR, ethernet, and RS232 over single category 6a F/UTP or better twisted pair cable. The DL-HD100-H3 can 100m supports transmit 4K resolutions up to 4K@60Hz 4:4:4 up to . - Page 3 HDMI 2.0b and HDCP 2.3 compliant. HDBT 3.0 technology built-in. It supports resolutions up to 4K@60Hz 4:4:4 8bit along with other signals, such as IR, RS232, 1GbE ETHERNET and optical audio to 330ft/100m via Cat 6A F/UTP or above cable. Additional HDMI loop-out on the transmitter with auto 4K-to-1080P scaler built-in.
- Page 4 Transmission Distance Note: Straight-through category cable wired T568B standard recommended. For max HDMI 2.0 performance, recommended cable is: Cat 6A U/FTP or above. The extender supports two transmission modes: High-bandwidth and Low- bandwidth. When the extender is set to High-bandwidth mode (set the pin4 of the DIP switches of the transmitter and receiver to “Up”...
-
Page 5: Panel Descriptions
Display Video Source Maximum Distance HDMI HDMI Cable Cable Wall mounted link segment Patch Patch VS3100RX VS3100TX RJ45 RJ45 The standard specifies the following lengths for the three-segment cable installation: X = Left-side patch cable length ≤ 5 [meter] Y = Right-side patch cable length ≤... -
Page 6: Video Led
Name Description On: HDBT link is normal. LINK LED Off: No HDBT link or link error. Green: Source video is being transmitted. Red: Pattern video with HDCP is being transmitted. VIDEO LED Blue: Pattern video without HDCP is being transmitted. Off: No video is being transmitted. -
Page 7: Audio Out
Name Description directional PoC, whether the power adapter is connected to the transmitter or receiver, it can power both the units. Connect to RS232 enabled devices, for RS232 RS232 pass-through. HDBT OUT Connect to the HDBT IN port of the receiver. HDMI IN Connect to an HDMI source device. - Page 8 Name Description pass-through. Connect to the HDBT OUT port of the HDBT IN transmitter. HDMI OUT Connect to an HDMI display. OPTICAL IN Connect to an optical out port of a display. Connect to local area network or Ethernet device ETHERNET for Ethernet pass-through.
- Page 9 Wiring Warnings: Before wiring, disconnect the power from all devices. During wiring, connect and disconnect the cables gently. The Cat x cable should not exceed the maximum cable length, refer to the specifications section for details. Audio and Video Extender Mode: Connect an HDMI source to HDMI IN port of the transmitter, and connect an HDMI display to HDMI OUT port of the receiver.
- Page 10 OPTICAL audio de-embedded mode: When setting the DIP Switches to OPTICAL audio de-embedding mode (see “DIP Switch Settings” to get detail information), the audio receiver connected to OPTICAL OUT port and AUDIO OUT port will output the de- embedded audio from HDMI IN (See Figure 2). Cat x Figure 1...
- Page 11 Cat x Figure 2 Additional control connection selection: RS232 Pass-through: Connect a RS232 control system/controlled device to the transmitter/receiver, and connect a RS232 controlled/control system device to the receiver/transmitter for serial communication. See “RS232 Pass-Through” section to get detail information. IR Pass-through: Connect the IR emitter cable provided to IR OUT port of ...
-
Page 12: Test Pattern Generation
side using display remote (See Figure 1). Ethernet Pass-through: Connect ETHERNET port transmitter/receiver to local area network, and connect a laptop to the ETHERNET port of the receiver/transmitter, the laptop can access to the connected local area network (See Figure 1). Test Pattern Generation The extender kit supports generation of a test pattern video signal, with different HDCP capabilities. -
Page 13: Dip Switch Settings
DIP Switch Settings Using DIP switches on front panel of the transmitter and receiver to set audio mode, set upgrade function and bandwidth rate. 1 2 3 4 Please refer to the following table to set: Transmitter: Function Audio EDID 2CH (default) Down Audio EDID pass-through Audio de-embed (default) - Page 14 IN port of the receiver. If audio source signal is compressed audio, AUDIO OUT port will be muted. Both Valens firmware of the transmitter and receiver can be upgraded through FW port of the transmitter/receiver. Set the DIP switch of the transmitter/receiver to “x, x, Up, x”.
-
Page 15: Rs232 Pass-Through
RS232 Pass-Through RS232 ports can be used for bi-directional RS232 signal pass-through between the transmitter and receiver. Connect a RS232 master/slave Device to RS232 port of transmitter /receiver and connect a slave/master device to RS232 port of receiver/transmitter. Connect HDBT OUT of the transmitter to HDBT IN of the receiver. When all is set, RS232 signal can be passed through bi-directionally between two RS232 devices. -
Page 16: Cabling Requirements
When using shielded category cabling ALWAYS..use shielded connectors ..properly ground the category cable For optimized HDBaseT performance use the following Liberty Wire and Cable branded cabling; Category 6 plenum; 24-4P-P-L6SH Category 6A plenum; 24-4P-P-L6ASH Category 6 NON-plenum; 24-4P-L6SH Category 6A NON -plenum;... -
Page 17: Technical Specifications
TECHNICAL SPECIFICATIONS Model DL-HDE100-H3 Taiwan OWNERS MANUAL DL-HDE100-H3... - Page 18 Thank you for your purchase. For technical support please call our toll-free number at 800-530-8998 or email us at supportlibav@libav.com www.libav.com 800-530-8998 Rev 222112 OWNERS MANUAL DL-HDE100-H3...
Need help?
Do you have a question about the Digitalinx Series and is the answer not in the manual?
Questions and answers