Page 1
MP330 MP348 MP360 MP330, MP348 And MP360 Brush Mulcher OPERATOR’S MANUAL Issue Date: April 2025...
Page 2
Following is a list of videos and documents available on Baumalight’s website and also on YouTube to help and enhance maintaining the brush mulcher. The list below was current at the time this manual was issued. Additional content may be available.
Page 3
Activity ID Number Activity Name Description Item Available...
Operator’s Manual. This manual covers the MP330, MP348 and MP360 Baumalight Brush Mulchers. Use the Table of Contents as a guide to locate required information. Keep this manual handy for frequent reference and to pass on to new operators or owners. Call...
1�2 Intended Use And Foreseeable Misuse The brush mulcher is designed to be used by experienced operators, trained in the safe operation of a tractor and trained in the hazards related to using the brush mulcher and the safe use of the mulcher for the intended purpose.
2 SAFETY 2�1 Safety Alert Symbol And Safety Words You must read, understand and follow the CAUTION instructions given operating unit CAUTION - Indicates a hazardous manufacturers, as well as the instructions in this situation, which, if not avoided, could manual.
Use brush mulcher only for the designed may be found at: www.asae.org or www.osha.gov. applications� If you do not understand any part of this manual, Any other use may result in personal contact Baumalight at 866-820-7603. injury, damage to equipment and may void the warranty�...
Safety signs are identified in Section 3 of this manual. Prevent electrocution� • Replacement safety signs are available from Death or serious injury can result if your Baumalight dealer. equipment comes near or contacts power lines� Do Not Allow Riders Electrocution can occur without direct •...
Raised Attachment Stay Clear Of Rotating Driveshaft WARNING WARNING Crushing hazard� Entanglement in a rotating driveshaft can cause serious injury or death� Raised, unsupported brush mulcher can fall, resulting in death or serious injury� Keep tractor shields and driveshaft shields in place at all times� DO NOT Never enter the area under a raised operate without driveshaft guards�...
WARNING Do not make unauthorized modifications. Contact Burn hazard� Baumalight at 866-820-7603 before you weld, cut/ drill holes, or make any other modifications. Hot and high pressure hydraulic oil� Always use Baumalight replacement parts. Allow oil to cool before servicing�...
3 SAFETY SIGNS 3�1 MP348 And MP360 The two and four panel safety decals are pictorial A. D005223 ^ WARNING - Rotating rotor hazard. and have a yellow background. The panel with a Keep back 75 m while machine is operating. triangle indicates the potential hazard.
Page 13
C. D005129 ^ WARNING G. D005335 ^ WARNING E. D005029 The ^ WARNING Rotating parts hazard. Do Wear personal protective Read and understand safety not reach into machine. equipment appropriate for signs on the machine and Keep away from machine. the job.
3�2 MP330 The two and four panel safety decals are pictorial A. D005223 ^ WARNING - Rotating rotor hazard. and have a yellow background. The panel with a Keep back 75 m while machine is operating. triangle indicates the potential hazard. The panel Wait for rotor to stop before approaching without a triangle indicates how to avoid the hazard.
Page 15
C. D005129 ^ WARNING G. D005031 ^ WARNING E. D005029 ^ WARNING Rotating parts hazard. Do Wear personal protective Read and understand safety not reach into machine. equipment appropriate for signs on the machine and Keep away from machine. the job. operating instructions in this manual before operating machine.
4 OPERATION 4�1 Preparation For Use 4�2 Driveshaft Dimension A PTO driveshaft is supplied with the machine. To WARNING accompany the variety of 3 point hitch geometry available today, the driveshaft can be too long for Drilling, sawing, sanding or machining most machines or too short for others.
Page 17
d. Use a file to remove burrs from edges that were cut. e. Assemble the 2 ends of the shaft. Make sure shaft can telescope freely. If it does not, separate the 2 parts and inspect for burrs or cuttings on shaft ends. Be sure it telescopes freely before installing.
4�3 Pre-Operation Check List Check-mark Check these items: Frequency Check the three linch pins on the hitch to verify they are Each operation. securely fastened. Verify the pins on each end of the drive shaft are secured. Each operation. Verify the safety chains on the drive shaft are securely Each operation.
4�5 Attach Brush Mulcher 4�6 Detach Brush Mulcher WARNING WARNING To prevent injury or machine damage Prevent serious injury or death caused by unexpected movement: put transmission in “Park” and check the full range of hitch for interference, Park tractor on a level surface� 1�...
4�9 First Time User Tips 4�7 Transporting 1. Verify all reflectors and Slow Moving Vehicle • First, operate all functions in a clear area with (SMV) sign are visible. the tractor at idle speed to get a good feel for the controls before you actually move into any 2.
Page 21
WARNING Wear an approved dust mask or respirator� Follow local, state federal regulations�...
4�10 Field Operation WARNING WARNING Entanglement in a rotating driveshaft Wear an approved dust mask or can cause serious injury or death� respirator� Keep tractor shields and driveshaft Follow local, state federal shields in place at all times� DO NOT regulations�...
Page 23
WARNING Never approach brush mulcher before cutting wheel has come to a complete stop�...
5 SERVICE AND MAINTENANCE 5�1 Maintenance Maintenance Chart General Inspection Inspect the unit for any buildup of Daily contamination (dirt, stones, etc.). Cutting Teeth Check and rotate or replace one at a time Every 4 hours. as necessary. With daily use expect to replace 4 to 6 teeth per day.
5�2 Inspections WARNING WARNING Prevent serious injury or death caused Wear an approved dust mask or by unexpected movement: respirator� Park tractor on a level surface� 1� Follow local, state federal Engage tractor park brake� 2� regulations� Disengage PTO� 3� Inspect the unit for any buildup of contamination Shut off engine and remove key�...
5�3 Check Belt Tension 1. Lower mulcher to ground. 2. Set parking brake, stop engine and remove key. WARNING Moving parts can crush and cut� Keep clear of moving components� Follow lockout procedure before servicing� 3. Open inspection cover (A). 4.
5�4 Replace Belt 1. Lower mulcher to ground. 11. Align pulley holes with non threaded holes in hub (F) and install bolts (D). 2. Set parking brake, stop engine and remove key. 12. Place a straight edge (I) on drive pulley and rotor pulley.
5�5 Adjust Slip Clutch WARNING Entanglement in a rotating driveshaft can cause serious injury or death� Disconnect and lockout power source before adjusting or servicing� CAUTION Slip clutch may be hot� Wait for clutch to cool before adjusting or servicing� Bondioli Driveshafts 4-Disk 120 Hp 1,000 rpm OEM Part Number...
(C) on tooth holder. 6. Install spacer (A) and locknut. Tighten ⅜ inch locknut to 65 lb/ft (88 Nm) of torque. Note: Parts breakdown can be found on Baumalight’s website. www.baumalight.com Note: Parts breakdown can be found on Baumalight’s website. www.baumalight.com...
Install plug (B) and fill gearbox through hole (A) until oil is 2 in. (51 mm) below plug hole (A). Note: Parts breakdown can be found on Note: Parts breakdown can be found on Baumalight’s website. www.baumalight.com Baumalight’s website. www.baumalight.com...
5�10 Rotor Bearings Determine lubrication interval from chart below. The bearings are factory lubricated with a lithium Typical lubrication quantity is 1 pump from a or lithium complex base grease which is suitable standard grease gun. for most applications. Select a grease that is compatible with a lithium or lithium complex Bearing Operation grease.
6 TROUBLESHOOTING PROBLEM CHECK SOLUTION Rotor does not spin. Rotor jammed. Remove material from rotor. Verify PTO driveshaft is Connect driveshaft to trac- connected properly. tor. Slip clutch is slipping. Remove material from rotor. Rotor rotates slow or sluggish. Drive belt loose. Tighten drive belt.
7 STORAGE 7�1 Storing Mulcher 1. Store mulcher in a dry place. 2. Clean mulcher thoroughly. Dirt and wood chips will draw moisture and cause rust. 3. Check condition of cutting teeth. Replace as necessary. (See Service and Maintenance section.) 4.
The manufacturer is under no circumstances liable for carrier unit damage of any kind. The manufacturer is not liable for the maintenance of the product. Baumalight will not cover time to diagnose and repair compatibility issues between carrier and attachment.
Page 36
For parts, specifications and the latest machine information please visit our website. www�baumalight�com MTB MFG INC. CORPORATE HEADQUARTERS 4575 Powell Rd., Wallenstein, Ontario Canada N0B 2S0 Phone - 519.698.9864 www�baumalight�com...
Need help?
Do you have a question about the MP330 and is the answer not in the manual?
Questions and answers