Do you have a question about the MP348 and is the answer not in the manual?
Questions and answers
Kerry Brunner
March 10, 2025
Does the slip clutch on mp48 need adjustment?
1 comments:
Mr. Anderson
March 10, 2025
The slip clutch on the Baumalight MP348 may need adjustment if it is slipping. Signs of this include the rotor rotating slowly or sluggishly. To address this, check if the slip clutch is hot, as a hot clutch does not grip properly. If slippage occurs, reduce strain by using a lower-powered tractor, traveling slower, or adjusting the flow control knob to a lower setting.
Operator’s Manual. This manual covers the Baumalight Brush Mulcher, models MP348 and MP360. Use the Table of Contents as a guide to locate required information. Keep this manual handy for frequent reference and to pass on to new operators or owners. Call...
1.2 Intended Use And Foreseeable Misuse The brush mulcher is designed to be used by experienced operators, trained in the safe operation of a tractor and trained in the hazards related to using the brush mulcher and the safe use of the mulcher for the intended purpose.
2 SAFETY 2.1 Safety Alert Symbol And Safety Words You must read, understand and follow the ^ CAUTION instructions given operating unit CAUTION - Indicates a hazardous manufacturers, as well as the instructions in this situation, which, if not avoided, could manual.
Additional information applications� may be found at: www.asae.org or www.osha.gov. If you do not understand any part of this manual, Any other use may result in personal contact Baumalight at 866-820-7603. injury, damage to equipment and may void the warranty�...
Safety signs are identified in Section 3 of this • Do not exceed load capacity of equipment. manual. • Replacement safety signs are available from your Baumalight dealer. Avoid Powerlines & Underground Utilities Do Not Allow Riders ^^ DANGER •...
Detach Brush Mulcher Hazards From Modifying Safely Equipment Do not make any alterations to your brush Detach brush mulcher on a firm and level surface. mulcher. Altering the equipment may cause unsafe Brush mulcher may fall over if detached on sloping conditions and may void the manufacturer’s or soft surface.
^ WARNING for the job. Burn hazard� Do not make unauthorized modifications. Contact Baumalight at 866-820-7603 before you weld, cut/ Hot and high pressure hydraulic oil� drill holes, or make any other modifications. Allow oil to cool before servicing� Always use Baumalight replacement parts.
4 OPERATION 4.1 Preparation For Use Driveline Dimension ^ WARNING A PTO driveline is supplied with the machine. To Wear an approved respirator (N95 Type accompany the variety of 3 point hitch geometry as a minimum)� available today, the driveline can be too long for most machines or too short for others.
Page 13
c. Use a hacksaw to cut dimension (C) from both ends. Cut both plastic tubes and metal cores. d. Use a file to remove burrs from edges that were cut. e. Assemble the 2 ends of the shaft. Make sure shaft can telescope freely. If it does not, separate the 2 parts and inspect for burrs or cuttings on shaft ends.
4.3 Pre-Operation Check List Check-mark Check these items: Frequency Check the three linch pins on the hitch to verify they are Each operation. securely fastened. Verify the pins on each end of the drive shaft are secured. Each operation. Verify the safety chains on the drive shaft are securely Each operation.
4.5 Attach Brush 4.6 Detach Brush Mulcher Mulcher ^ WARNING ^ WARNING To prevent injury or machine damage Prevent serious injury or death caused put transmission in “Park” and check by unexpected movement: the full range of hitch for interference, Park tractor on a level surface�...
4.8 Carbide Teeth 4.7 Transporting Break-In 1. Verify all reflectors and Slow Moving Vehicle During the first few hours of use, avoid hitting (SMV) sign are visible. stones as much as possible to allow the carbide teeth to wear slightly. This can be done by keeping 2.
4.9 First Time User Tips 4.10 Field Operation • First, operate all functions in a clear area with ^ WARNING the tractor at idle speed to get a good feel for the controls before you actually move into any Entanglement in a rotating drive line brush.
Page 18
^ WARNING Never operate brush mulcher when other people are in the vicinity� Debris can be thrown several feet from cutting area� Keep all shields in place� 1. Attach brush mulcher to tractor. See Attaching Brush Mulcher To Tractor in this section. ^ WARNING Prevent serious injury or death�...
5 SERVICE And MAINTENANCE 5.1 Maintenance Maintenance Chart General Inspection Inspect the unit for any buildup of Daily contamination (dirt, stones, etc.). Cutting Teeth Check and rotate or replace one at a time Every 4 hours. as necessary. With daily use expect to replace 4 to 6 teeth per day.
5.3 Check Belt Tension 1. Lower mulcher to ground. 2. Set parking brake, stop engine and remove key. ^ WARNING Moving parts can crush and cut� Keep clear of moving components� Follow lockout procedure before servicing� 3. Open inspection cover (A). 4.
5.4 Replace Belt 1. Lower mulcher to ground. 11. Align pulley holes with non threaded holes in hub (F) and install bolts (D). 2. Set parking brake, stop engine and remove key. 12. Place a straight edge (I) on drive pulley and rotor pulley.
5.5 Adjust Slip Clutch ^ WARNING Entanglement in a rotating drive line can cause serious injury or death� Disconnect and lockout power source before adjusting or servicing� ^ CAUTION Slip clutch may be hot� Wait for clutch to cool before adjusting or servicing� Bondioli Driveshafts 4-Disk 120 Hp 1,000 rpm OEM Part Number...
(C) on tooth holder. 6. Install spacer (A) and locknut. Tighten ⅜ inch locknut to 65 lb/ft (88 Nm) of torque. Note: Parts breakdown can be found on Baumalight’s website. www�baumalight�com Note: Parts breakdown can be found on Baumalight’s website. www�baumalight�com...
Install plug (B) and fill gearbox through hole (A) until oil is 2 in. (51 mm) below plug hole (A). Note: Parts breakdown can be found on Baumalight’s website. www�baumalight�com Note: Parts breakdown can be found on Baumalight’s website. www�baumalight�com...
NOT grip. 2. Slippage on the clutch occurs if there is more power than the unit is rated for: Model MP348 is rated for 25 - 45 hp input. Model MP360 is rated for 30-50 hp input. A bigger tractor can be used if it is idled down.
8 WARRANTY This product is warranted to be free of defects in materials and workmanship under normal use and service, for a period of one year from the date of purchase, when operated and maintained in accordance with the Operating and Maintenance Instructions supplied with this unit. This warranty does not cover misuse or negligence.
Page 28
For parts, specifications and the latest machine information please visit our website. www�baumalight�com MTB MFG INC. CORPORATE HEADQUARTERS 4575 Powell Rd., Wallenstein, Ontario Canada N0B 2S0 Phone - 519.698.9864 Toll Free - 866.820.7603 Fax - 519.698.1087 www�baumalight�com...
Need help?
Do you have a question about the MP348 and is the answer not in the manual?
Questions and answers
Does the slip clutch on mp48 need adjustment?
The slip clutch on the Baumalight MP348 may need adjustment if it is slipping. Signs of this include the rotor rotating slowly or sluggishly. To address this, check if the slip clutch is hot, as a hot clutch does not grip properly. If slippage occurs, reduce strain by using a lower-powered tractor, traveling slower, or adjusting the flow control knob to a lower setting.
This answer is automatically generated
How do you take the plastic sleeve off the shafts