Subscribe to Our Youtube Channel
Related Manuals for Total TWLC1256
Summary of Contents for Total TWLC1256
- Page 1 WALL CHASER TWLC1256,UTWLC1256,TWLC1256-4 TWLC1256-6,TWLC1256-8,TWLC1256-9,TWLC1256S TOTAL TOOLS WORLD TOTAL TOOLS WORLD SCAN FOR VIDEO 1500W...
- Page 2 The symbols in instruction manual and the label on the tool Double insulated for additional protection. Read the instruction manual before using. CE conformity. Wear safety glasses, hearing protection and dust mask. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
- Page 3 GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
- Page 4 a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. 3) Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
- Page 5 and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
- Page 6 d) Wheels must be used only for recommended applications. For example: do not grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter. e) Always use undamaged wheel flanges that are of correct diameter for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage.
- Page 7 Residual risks Even when the power tool is used as prescribed it is not possible to eliminate all residual risk factors. The following hazards may arise in connection with the power tool’s construction and design: a) Health defects resulting from vibration emission if the power tool is being used over longer period of time or not adequately managed and properly maintained.
-
Page 8: Safety Instructions
SAFETY INSTRUCTIONS General Power Tool Safety Warnings WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. - Page 9 f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. g. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
- Page 10 ADDITIONAL SAFETY INSTRUCTIONS FOR YOUR WALL CHASER Maintain the tool with care 1) Keep cutting equipment sharp and clean, so you will achieve a good result, safely. 2) Follow the directions for lubrication and replacement of parts. 3) Inspect the power cord regularly and have a damaged cord repaired by an authorized service agent.
- Page 11 8. Warning! Always use the appropriate safety equipment that is required for the product.e.g. Goggles/Safety Spectacles,Ear defenders(essential with tools with a noise rating of over 85dB(A),Golves and face masks,in all cases ensure that the safety equipment is in good condition ! Warning! Never drill, cut or chase in surfaces, in which electrical cabling, gas or water pipes could be concealed.
- Page 12 10 11 12 16 17 ON/ OFF TRIGGER SWITCH ‘LOCK OFF’ BUTTON ATTACHMENT POINT FOR AUXILIARY HANDLE FIXED GUARD CONNECTION TO DUST EXTRACTION GUIDE WHEEL BOLT FOR FIXING GUARD FLANGE CAP LOCK KNOB FLANGE CAP 10 ADJUSTING CHANNEL DEPTH KNOB 11 BASE PLATE...
-
Page 13: Technical Data
17 DIAMOND CUTTING DISC 18 CUTTING DIRECTION ARROW 19 AUXILIARY HANDLE 20 CHISEL 21 SPANNER TECHNICAL DATA TWLC1256 TWLC1256-4(IRAM Plug) Model No.: UTWLC1256 TWLC1256-6(ISRAEL Plug) TWLC1256-8(BS Plug) TWLC1256-9(INMENTRO Plug) TWLC1256S(SAA Plug) Voltage: 220-240V~50/60Hz 110-120V~50/60Hz Input power: 1500W 1500W No-load speed: 10500/min... - Page 14 OPERATION INSTRUCTIONS WARNING Before using your wall chaser be sure to read this instruction manual carefully! NEVER press the spindle locking button while the machine is running. ALWAYS unplug the tool from the power supply BEFORE carrying out any adjustments or maintenance. 1.
- Page 15 Adjusting the groove width (the distance between the two diamond wheels) The width of grooving in the workpiece can be adjusted by changing the number of the distance washers as shown in the table: Groove width:29.8mm Groove width:25.5mm Groove width:21.2mm Groove width:16.9mm Groove width:12.6mm Groove width:8.3mm...
- Page 16 Now mount the outer flange and tighten using the spanner provided, again note that this is a LEFT HAND thread so tighten in an anti-clockwise direction. At the same time depress the spindle-locking button.(see fig10&11) Finally lower the flange cap and re-tighten the flange cap lock knob and the adjusting channel depth knob.(see fig12) 3.
- Page 17 4. Removing the Fixed guard (Alternative blade fixing method) In order to clean the internal guard area from debris you can remove the fixed guard and gain access to the internal cutting head area.Firstly completely unscrew and remove the adjusting channel depth knob and its sight marker,now using the Allen key supplied undo the two guard fixing bolts and lift off the fixed guard.
- Page 18 5. Fitting the auxiliary handle For your own safety we recommend that you fit the auxiliary handle at all times thus maintaining complete control of the tool during operation. To fit the handle locate to the fixed guard and simply screw into place and secure.(see fig26) 6.
- Page 19 7. Switching ON and OFF The machine is equipped with a safety lock off button to prevent unintentional starting.To switch on simply depress the safety lock of button and then depress the ON/OFF trigger.To switch off release the ON/OFF trigger. (see fig 28) 8.
-
Page 20: Maintenance
MAINTENANCE Problem Possible cause Solution The electric motor 1) The overheating 1) Wait several minutes until becomes hot and cuts protection has been the machine has cooled out. activated. down, then re-start the 2) The motor is defective. machine. 2) Take the machine to your dealer for inspection and / or repair The machine is... - Page 21 TWLC1256,UTWLC1256,TWLC1256-4, TWLC1256-6,TWLC1256-8,TWLC1256-9, TWLC1256S Exploded view...
- Page 22 TWLC1256,UTWLC1256,TWLC1256-4, TWLC1256-6,TWLC1256-8,TWLC1256-9, TWLC1256S Spare part list No. Part Description Qty No. Part Description Knob M5 35 External criclips 15 Knob M6 36 Spindle lock Guage holder 37 Bearing 626 Cutting depth guage 38 Gear housing Side handle 39 Screw ST5x35...
- Page 23 TOTAL TOOLS CO., PTE. LTD. No.45 Songbei Road，Suzhou Industrial Park，China. MADE IN CHINA T1120.V04 1500W...
Need help?
Do you have a question about the TWLC1256 and is the answer not in the manual?
Questions and answers