Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Black & Decker ADBEG115
Summary of Contents for Black & Decker ADBEG115
- Page 1 ® BEG010 www.blackanddecker.com.au ADBEG115 www.blackanddecker.co.nz...
-
Page 5: Intended Use
(RCD) Intended use protected supply. Use of an RCD reduces the risk of Your BLACK+DECKER BEG010, ADBEG115 angle grinders electric shock. have been designed for grinding, cutting, sanding and wire brushing metal or masonry/concrete, using appropriate type of 3. - Page 6 ENGLISH (Original instructions) tools. Such preventive safety measures reduce the risk of ♦ Do not use accessories which are not specifically designed and specified by the tool manufacturer. Just starting the power tool accidentally. because the accessory can be attached to your power d.
-
Page 7: Kickback And Related Warnings
(Original instructions) ENGLISH Do not attach a saw chain woodcarving blade or toothed ♦ Never lay the power tool down until the accessory saw blade. Such blades create frequent kickback and loss of has come to a complete stop. The spinning accessory control. -
Page 8: Safety Warnings Specific For Sanding Operations
ENGLISH (Original instructions) Children should be supervised to ensure that they do not power tool motionless until the wheel comes to a play with the power tool. complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion Residual risks. - Page 9 (Original instructions) ENGLISH Labels on tool Warning! Never use the tool without the guard. The following pictograms, along with the date code, are shown Fitting the side handle on the tool: Screw the side handle (4) into one of the mounting holes Warning! To reduce the risk of injury, the user in the tool.
- Page 10 ENGLISH (Original instructions) Edge grinding with grinding discs flange (13) using the two-pin spanner (14) (fig. D). Remove the outer flange (13), the sanding disc (16) and Wheels used for cutting and edge grinding may break or kick the backing pad (15). back if they bend or twist while the tool is being used to do cutoff work or deep grinding.
- Page 11 (Original instructions) ENGLISH contains lead without a chemical analysis, we recommend and for smoothing irregular surfaces. the following precautions when sanding any paint: Note: The same precautions should be taken when wire No children or pregnant women should enter the work brushing paint as when sanding paint.
-
Page 12: Maintenance
ENGLISH (Original instructions) Maintenance Mounting cutting wheels Place the unthreaded backing flange on spindle with the Your BLACK+DECKER cordedpower tool has raised section (pilot) facing up. The raised section (pilot) on been designed to operate over a long period of time with a the backing flange will be against the wheel when the minimum of maintenance. -
Page 13: Troubleshooting
(Original instructions) ENGLISH Troubleshooting Additional Information for Guards and Accessories Problem Possible cause Possible solution ≤10 mm Unit will not Cord not plugged Plug tool into a start. working outlet. Cord or switch is Have cord or switch damaged. replaced at a BLACK+DECKER service center or When using segmented diamond wheels,... -
Page 14: Technical Data
BEG010 ADBEG115 Input voltage Power input Rated speed 12000 12000 BEG010, ADBEG115 Angle grinder Disc bore Black & Decker declares that these products described under "technical data" are in compliance with: Max disc thickness 2006/42/EC, EN 62841-1:2015+A11:2022; Grinding Wheel diameter EN IEC 62841-2- 3:2021+A11:2021. - Page 16 Australia & New Zealand Stanley Black & Decker www.blackanddecker.com.au www.blackanddecker.co.nz Tel.1800 338 002 (Aust) or Tel. 0800 339 258 (NZ) 810 Whitehorse Road Box Hill VIC 3128, Australia 03/2024 NA272891...
Need help?
Do you have a question about the ADBEG115 and is the answer not in the manual?
Questions and answers