Black & Decker BEG110 Original Instructions Manual
Hide thumbs
Also See for BEG110:
- User manual ,
- Original instructions manual (33 pages) ,
- Manual (17 pages)
Subscribe to Our Youtube Channel
Related Manuals for Black & Decker BEG110
Summary of Contents for Black & Decker BEG110
- Page 1 English (original instructions) BEG110 BEG120 KFBEG110 KFBEG125 ADBEG125 BEG210 BEG220 www.blackanddecker.eu...
- Page 2 Fig. A Copyright BLACK+DECKER...
- Page 3 Fig. B Fig. C Fig. D Fig. E Fig. G Fig. F...
- Page 4 Fig. H Fig. I Fig. J Fig. K Fig. L Fig. M...
-
Page 5: Safety Instructions
) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part Your BLACK+DECKER BEG110, BEG120, KFBEG110, KFBEG125, of the power tool may result in personal injury. -
Page 6: Kickback And Related Warnings
English • Do not use accessories which are not specifically designed nOTE: The above warning does not apply for power tools and recommended by the tool manufacturer. Just because specifically designed for use with a liquid system. the accessory can be attached to your power tool, it does not Kickback and Related Warnings assure safe operation. -
Page 7: Additional Safety Warnings Specific For Abrasive Cutting-Off Operations
English Residual Risks Flanges for cut-off wheels may be different from grinding wheel flanges. Additional residual risks may arise when using the tool which • Do not use worn down wheels from larger power tools. may not be included in the enclosed safety warnings. These Wheel intended for larger power tool is not suitable for the higher risks can arise from misuse, prolonged use etc. - Page 8 English Voltage Drops towards the disc (A in Fig. D). When fitting a cutting disc, the raised centre on the outer flange must face away from the disc Inrush currents cause short-time voltage drops. Under (B in Fig. D). unfavourable power supply conditions, other equipment may •...
- Page 9 English • Place the sanding disc onto the backing pad. - No children or pregnant women should enter the work area where the paint sanding is being done until all clean up • Place the outer flange onto the spindle with the raised is completed.
-
Page 10: Maintenance
English • Continuously move the tool in a forward and back motion to • Remove the tool from work surface before turning tool off. avoid creating gouges in the work surface. Allowing the tool to Allow the tool to stop rotating before setting it down. rest on the work surface without moving, or moving the tool in a circular motion causes burning and swirling marks on the work WARNING! Let the tool work at its own pace. -
Page 11: Protecting The Environment
When using segmented diamond wheels, use only diamond wheels with a Weight peripheral gap not greater than 10 mm and negative rake angle. Level of sound pressure according to EN 62841: BEG110, BEG120, KFBEG110, KFBEG125, Sound pressure (L ) 92 dB(A), uncertainty (K) 3 dB(A) ADBEG125... -
Page 12: Ec Declaration Of Conformity
Caution! Applications such as wire brushing may have different vibration emissions. EC DECLARATION OF CONFORMITY MACHINERY DIRECTIVE BEG110, BEG120, KFBEG110, KFBEG125, ADBEG125,BEG210, BEG220 Angle grinder BLACK+DECKER declares that these products described under "technical data" are in compliance with: 2006/42/EC, EN 62841-1:2015+A11:2022;... - Page 16 Australia & new Zealand Australia & New Zealand Stanley Black & Decker Tel.1800 338 002 (Aust) www.blackanddecker.com.au 810 Whitehorse Road Box Hill Tel. 0800 339 258 (NZ) www.blackanddecker.co.nz VIC 3128, Australia België/Belgique/luxembourg Stanley Black & Decker Belgium BVBA Tel. NL +32 15 47 37 65 www.blackanddecker.be Egide Walschaertsstraat 16...
Need help?
Do you have a question about the BEG110 and is the answer not in the manual?
Questions and answers