Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Black & Decker BEG010A5
Summary of Contents for Black & Decker BEG010A5
- Page 1 ® BEG010 ADBEG115 www.blackanddecker.eu...
- Page 2 English (original instructions)
-
Page 5: Intended Use
(Original instructions) ENGLISH unavoidable, use a residual current device (RCD) Intended use protected supply. Use of an RCD reduces the risk of Your BLACK+DECKER BEG010, ADBEG115 angle grinders electric shock. have been designed for grinding, cutting, sanding and wire brush- ing metal or masonry/concrete, using appropriate type of discs. - Page 6 ENGLISH (Original instructions) starting the power tool accidentally. tool. Accessories running faster than their rated speed d. Store idle power tools out of the reach of children and can break and fly apart. do not allow persons unfamiliar with the power tool or ♦...
-
Page 7: Kickback And Related Warnings
(Original instructions) ENGLISH ♦ Regularly clean the power tool’s air vents. The selected wheel. Wheels for which the power tool was not motor’s fan will draw the dust inside the housing and designed cannot be adequately guarded and are unsafe. excessive accumulation of powdered metal may cause The grinding surface of centre depressed wheels electrical hazards. -
Page 8: Safety Warnings Specific For Sanding Operations
ENGLISH (Original instructions) the cut. The wheel may bind, walk up or kickback if the and the implementation of safety devices, certain residual power tool is restarted in the workpiece. risks can not be avoided. These include: Support panels or any oversized workpiece to Injuries caused by touching any rotating/moving parts. - Page 9 (Original instructions) ENGLISH If the supply cord is damaged, it must be replaced by the Place the disc (11) onto the spindle (5) as shown (fig. B). manufacturer or an authorised BLACK+DECKER Service If the disc has a raised centre (12), make sure that the Centre in order to avoid a hazard.
- Page 10 ENGLISH (Original instructions) Edge grinding wheels are not designed to withstand side Begin with coarse grit discs for fast, rough material removal. pressures caused by bending. Move to a medium grit paper and finish with a fine grit disc for Remove the tool from the work surface before turning the optimal finish.
- Page 11 (Original instructions) ENGLISH All surfaces in the work area should be vacuumed and available. Diamond blades for concrete cutting can also be thoroughly cleaned daily for the duration of the sanding used. NOTE: A closed, 2-sided Type 41 cutting wheel guard is sold project.
-
Page 12: Troubleshooting
ENGLISH (Original instructions) Troubleshooting Warning! Let the tool work at its own pace. Do not overload. Problem Possible cause Possible solution Carefully guide the cable in order to avoid accidentally Unit will not Cord not plugged Plug tool into a cutting it. -
Page 13: Technical Data
(Original instructions) ENGLISH Technical data Additional Information for Guards and Accessories BEG010 Type 2 ADBEG115 Type 2 ≤10 mm Input voltage Power input Rated speed 12000 12000 Disc bore Max disc thickness When using segmented diamond wheels, Grinding Wheel diameter use only diamond wheels with a peripheral Grinding wheel thickness gap not greater than 10 mm and negative... -
Page 14: Ec Declaration Of Conformity
ENGLISH (Übersetzung der ursprünglichen DEUTSCH (Original instructions) Anweisungen) file and makes this declaration on behalf of Terms and conditions of the Black & Decker 2-year guarantee Black & Decker. and the location of your nearest authorised repair agent can be obtained on the Internet at www.2helpU.com, or by contacting your local Black &... - Page 16 Australia & New Zealand Australia & New Zealand Stanley Black & Decker Tel. 1800 338 002 (Aust) www.blackanddecker.com.au 810 Whitehorse Road Box Hill Tel. 0800 339 258 (NZ) www.blackanddecker.co.nz VIC 3128, Australia België/Belgique/Luxembourg Stanley Black & Decker Belgium BVBA Tel. NL +32 15 47 37 65 www.blackanddecker.be Egide Walschaertsstraat 16...
Need help?
Do you have a question about the BEG010A5 and is the answer not in the manual?
Questions and answers