Page 1
Operation Manual No: 501095100002-EN Manual Version: A January 2025 Manual 产品说明书 Translated version Preface to 0808E All Operation Manual PRODU C T MAN U AL 0808E All (0808E All/2732E All) 0109500100 to current 0608E (2132E) G T JZ 0808E (2732E)
Page 3
Operating, servicing and maintaining this vehicle or equipment can expose you to chemicals including engine exhaust, carbon monoxide, phthalates and lead, which are known to cause cancer and birth defects or other reproductive harm. To minimize exposure and avoid breathing exhaust, do not idle the engine except as necessary, service your vehicle or equipment in a well- ventilated area and wear gloves or wash your hands frequently when servicing.
Page 5
To Users Thank you for choosing and using the machinery of Hunan Sinoboom In- telligent Equipment Co., Ltd. Use this machine only to transport tools to work locations and for performing tasks on the work platform. Only authorized personnel who have received appropriate MEWP training may operate this machine.
Page 6
Manual Revision History: Version Date Description January 2025 Original issue...
Page 7
The manual applies to the following models and serial numbers: Metric Trade Imperial Trade Model Serial No. Name Name 0808E All 0808E All 2732E All 0109500100 to current Note: • Check the machine model and serial number on the machine nameplate. The location of the name- plate can be found in the Decals Diagram section of the Operation Manual.
Without the written permission of Hunan Sinoboom Intelligent Sinoboom cannot foresee all the potential hazards re- Equipment Co., Ltd., this machine shall not be used in lated to this machine, so all parties involved should place high importance on safety issues.
3.3 TRAINER’S RESPONSIBILITIES • The trainer must be accredited by Sinoboom, have comprehensive knowledge training on the machine, and must have the required skills related to machine repair and maintenance. •...
CONTROLLERS AND INDICATORS 6.2 PLATFORM CONTROLLER (SINOBOOM CONTROL SYSTEM) Fig. 2 Platform Controller (Sinoboom Control System) Table 6-2 Description Name Keep holding the switch – all functions will be enabled to Enable switch operate. Left turn thumb button Press the button to steer the machine to the left.
Activate Drive and Steer Mode • Sinoboom Control System: Move the lift and lower/ drive and steer function enable switch down, the in- dicator under the switch will illuminate. The machine Fig. 1 will enter drive and steer mode.
8.1 REPORTING ACCIDENTS emergency stop button to stop the machine. In case of any accident involving Hunan Sinoboom Intel- 8.3 EMERGENCY LOWERING ligent Equipment Co., Ltd. products, Hunan Sinoboom Intelligent Equipment Co., Ltd. must be notified immedi- ately.
• The machine is not equipped with a brake for Method 2 (for Sinoboom Control System): towing control, so the towing vehicle must be able to control the machine at all times, other- 1. Park the machine on solid level ground.
Replace the tire if necessary. choose not to use the replacement tires recommended • Check each rim for damage, deformation or cracked by Hunan Sinoboom Intelligent Equipment Co., Ltd., the following specifications should be adhered to: welds. Replace the rim if necessary. •...
Hunan Sinoboom Intelligent Equipment Co., Ltd. recommends this task be per- formed by a factory-trained service technician, a person recognized by Sinoboom as one who, by qualification, certificate and training, has successfully demonstrated the ability and proficiency to service, repair and maintain the Sinoboom model in question.
Page 63
Preventive Maintenance Responsible Persons and Qualifica- tions for Performing Inspection and Preventive maintenance procedures shall be performed by qualified Sinoboom technicians. The frequency of the Maintenance inspection and maintenance must be increased as re- quired by environmental conditions, requirements and frequency of usage.
Page 69
Phone: +61 484 118 324 E-mail: sales@sinoboom.com Korea Subsidiary Mexican Subsidiary Sinoboom Korea Co., Ltd. SINOBOOM LATIN AMERICA, S. DE R. L. DE C. V. E-mail: sales@sinoboom.com Camino a Napoles Km. 2+370(Ll) Phone: +82-10-2533-1831 entronque a brecha Km.1(Ll) del Ejido San...
Need help?
Do you have a question about the 0808E All and is the answer not in the manual?
Questions and answers