Related Manuals for Safehold FALSLK
Summary of Contents for Safehold FALSLK
- Page 1 Shock Absorbing Lanyard Instruction Manual Note: For Declaration of Conformity See Page 19 Read and understand instructions before using this equipment Do not throw instructions away Designed in the UK SHUM-065 Iss 01...
- Page 2 Contents About & Warning Description Lanyard General use Diagrams Applications & Ground Appropiate Standards clearance Service Log Inspection Table Declaration Conformity...
- Page 3 Using the lanyard Limitations, Inspection Compatibility & Connections Labelling Post Fall, Maintenance, Connections, Servicing & Inspection, Storage Product Life & Disposal...
- Page 4 This manual covers all variants language of the country in which within the SafeHold fall arrest the product is to be used. lanyard range. If there is reason to doubt your fitness to safely absorb the shock...
-
Page 5: General Use
Failure to use the equipment properly can result in Any equipment must be as the serious injury or death. If in doubt, manufacturer intended. Do not use contact SafeHold Ltd. for advice. altered or modified equipment. All authorised users must reference product that... - Page 6 large enough ground clearance. is missing remove the device from Never remove a product's label as service immediately. it contains information important for the use of the device. If the label DESCRIPTION Single, Dual, Dual Single rebar carabiner carabiner rebar Material Polyester webbing / zinc plated steel connectors EN355:2002,...
- Page 7 Single leg User attachment Shock Pack hook Velcro shock Pack Cover with zip and label pack. Anchor attachment hook Elasticated polyester webbing Dual leg User attachment Dual Shock Pack hook anchor Anchor hooks for Anchor attachment 100% tie attachment hook hook...
-
Page 8: Using The Lanyard
USING THE LANYARD The SafeHold fall arrest lanyard is IMPORTANT deigned for use with the SafeHold Never use the lanyard with an fall arrest range. extension device this will A suitable assessment must be increase free fall. made of the work site, taking into... - Page 9 As per EN355:2002, Anchorage Connectors self-locking snap hooks SafeHold equipment is designed carabiners are required. for use with SafeHold approved components subsystems only. Non-approved components or subsystems may jeopardise the COMPATIBILITY Connecting component or if any connector does not lock, limitations: do not use the system.
-
Page 10: Correct Connection
CORRECT CONNECTION INSPECTION Fall arrest lanyards shall inspection schedule and checking inspected authorised list appropriate inspection person or rescuer before each use. intervals and procedures. The inspection shall be conducted The competent person should by a competent person other than keep a log of their inspection in the user. - Page 11 D-ring of the SHBH. made in case of a fall and made available to everyone on site. Fall arrest lanyards are designed STANDARDS The EU type-examination (Module Safehold harness range B) and conformity assessment hasbeen designed to meet the procedure...
- Page 13 Pregnant women or Some subsystem and component minors must not use SafeHold self- combinations may interfere with retracting lifelines. Failure to heed the operation of this equipment. this warning may result in serious Use caution when using this injury or death.
- Page 14 Snap hooks and carabiners used disengagement cannot occur. with this equipment must be self- SafeHold connectors (snap hooks locking. Ensure all connections and carabiners) are designed to are compatible in size, shape, and be used only as specified in each strength.
- Page 15 MAINTENANCE, SERVICING & STORAGE Cleaning: and water to clean the fall arrest lanyard and allow to dry naturally. Ensure the fall arrest lanyard is kept A clean fall arrest lanyard is easier free of excess paint, grease, dirt to inspect and will prolong its life. or other contaminants as this may cause the damage to the fall arrest DO NOT use heat to dry.
- Page 16 Labelling: See below for a typical lanyard label. All labels on the fall arrest lanyard must be present and fully legible. Label No.32101 (Rev. 1) WARNING *SHFAL - Fall Arrest Lanyard *Prior to use, understand all manufacturer instructions included with equipment at time of shipment.
-
Page 17: Service Log
SERVICE LOG Safehold LTD www.safe-hold.com Model #: User: Date of first use: Serial No: Date of manufacture: Pass Fail Date Results/Condition: Inspected by: Next Inspection Date:... - Page 18 Competent Component Inspection: User Person Ensure webbing is free from cuts, abrasion, wear and tears Check webbing under buckles for rubbing and deterioration. Check the tear pack has not Webbing deployed and shows no sign of wear or abrasion. Check the weave of the webbing for distortion resulting from loading.
-
Page 19: Eu Declaration Of Conformity
EU DECLARATION OF CONFORMITY This declaration of conformity is issued under the sole responsibility of the manufacturer: SAFEHOLD LTD: 1-3 Eaves Court Bonham Drive, Sittingbourne,ME10 3RY. compliance@safe-hold.com +44 (0) 1795 668862 Model No. FALSLK, FALSLR, FALTLK, FALTLR Product Description Model No. - Page 20 www.safe-hold.com...
Need help?
Do you have a question about the FALSLK and is the answer not in the manual?
Questions and answers