Safehold ADVANTAGE Instruction Manual

Harness
Hide thumbs Also See for ADVANTAGE:

Advertisement

Harness
Instruction Manual
Read and understand instructions before using this equipment
Do not throw instructions away
Designed in the UK
1
SHUM-060 Iss 01

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ADVANTAGE and is the answer not in the manual?

Questions and answers

Summary of Contents for Safehold ADVANTAGE

  • Page 1 Harness Instruction Manual Read and understand instructions before using this equipment Do not throw instructions away Designed in the UK SHUM-060 Iss 01...
  • Page 2 Contents About & Warning Description Harness Donning the harness Rescue Strop Waist-belt General use installation Diagrams Use & Shoulder & leg pad Limitations & Connections Applications Free-falls & operation installation & Inspection & Standards Swing fall compatibility Body support, Disposal, Maintenance, Labels Service Log Inspection...
  • Page 3: General Use

    Any equipment must be as the harness, rigger's harness maintenance, periodic contact SafeHold Ltd. for advice. manufacturer intended. Do not use and their associated accessories examination and for repair in the altered or modified equipment. including the waist belt, leg pads,...
  • Page 4 Always ensure a potential fall path it contains information important to Rigger's Harness is free from obstructions and has a the use of the device. If the label Lanyard parking large enough ground clearance. is missing remove the device from keeper Never remove a product's label as service immediately.
  • Page 5 DONNING THE HARNESS Unfasten leg and chest quick To Fasten the Buckle connectors / buckles. Hold the square buckle in one Hold up the harness by hand and the three bar buckle the dorsal D and check the in the other. Step 3 Step 2 webbing is not twisted.
  • Page 6 Rescue Strop use: Shoulder pad installation in the position shown. the fall arrest connector. Undo the Velcro securing the Detach the connector and Undo the zip and the popper Fold over the bottom retaining strop to the back strap of the raise or lower the user to buttons on the shoulder pad.
  • Page 7: Correct Connection

    As per EN360:2002, Anchorage Connectors self-locking snap hooks SafeHold equipment is designed carabiners required. for use with SafeHold approved anchorage to which the SRL/ components subsystems RTFA attaches must meet the only. Non-approved components requirements of EN362:2004. or subsystems may jeopardize the...
  • Page 8 STANDARDS The EU type-examination (Module into UK law and amended, and the B) and conformity assessment following harmonized standards. procedure (Module were The Safehold harness range has conducted CCQS Certification Services Limited, Block been designed to meet the Blanchardstown Corporate Park,...
  • Page 9 (dorsal) D-ring. to withstand falls. Pregnant women Do not use a body belt for free fall Some subsystem and component or minors must not use SafeHold Dual SRLs/RTFAs are connected applications. combinations may interfere with fall protection products. Failure to the operation of this equipment.
  • Page 10 Disposal: disposing of the harness, cut Labelling: the webbing in multiple places Dispose of the harness if it has See below for the a typical harness label. All labels on the harness must be or otherwise disable the harness been subjected to fall arrest forces present and fully legible.
  • Page 11: Service Log

    Component Inspection: User Competent Person SERVICE LOG Ensure webbing is free from cuts and abrasion, wear and Safehold LTD www.safe-hold.com tears Model #: User: Check webbing under buckles Date of first use: Serial No: for rubbing and deterioration. Webbing Date of manufacture:...
  • Page 12: Eu Declaration Of Conformity

    EU DECLARATION OF CONFORMITY EU DECLARATION OF CONFORMITY This declaration of conformity is issued under the sole responsibility of the manufacturer: SAFEHOLD LTD: 1-3 Eaves Court Bonham Drive, The EU type-examination (Module B) and conformity assessment Sittingbourne, ME10 3RY. procedure (Module D) were conducted CCQS Certification Services compliance@safe-hold.com +44 (0) 1795 668862...
  • Page 13: User Notes

    USER NOTES EU DECLARATION OF CONFORMITY This declaration of conformity is issued under the sole responsibility of the manufacturer: SAFEHOLD LTD: Unit 15, Regis Ind. Estate, Dorset Road, Sheerness, Kent, ME12 1LY. compliance@safe-hold.com +44 (0) 1795 668862 Module B & D is carried by APAVE Model No.
  • Page 14 USER NOTES USER NOTES...
  • Page 15 www.safe-hold.com...

Table of Contents