Advertisement
Quick Links
Assembly Instructions
Assembly Instructions
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt.
To report information regarding missing parts or damage, to purchase parts or
accessories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
Assembly Tips:
• Assemble the console in its final location.
• To facilitate assembly, keep the fasteners finger-tight until the
console is completely together. Then tighten securely.
• Do not tighten component fasteners completely until all have
been installed. Keeping them loose will help with alignment
between parts during assembly.
• When a corner module is used with two double worksurfaces that have equipment rack support, a mid-support leg usually is not necessary
• When a corner module is next to a double worksurface, an equipment rack or mid-support leg should be used to support the double worksurface
• Mid-support legs are used at the seam between two worksurfaces of the same height
• End-support legs are used at the end of a worksurface
Corner Module
worksurface
1
2 open
Equipment
spaces
Rack
Note: These instructions represent assembly of all the structural components available for the Elite Console. Due to the various console
configurations and order combinations available, some items shown may not be included with your particular unit, and some assembly steps
may not apply. Before beginning assembly, please review these instructions.
Important
Worksurface Support Guidelines
For adequate support, areas under worksurfaces generally should not
exceed a span of more than 2 open spaces (or wall filler panels) wide.
Mid-support leg at
worksurface connection
2
1
2
Equipment
Rack
2 open
spaces
Equipment
Rack
Elite Console
68XXX series
Mid-support leg at
worksurface connection
1
2
1
2
2 open
spaces
0108630R12 Page 1 of 10
4mm
Equipment
Rack
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Spectrum Elite Console 68 Series
Summary of Contents for Spectrum Elite Console 68 Series
- Page 1 To report information regarding missing parts or damage, to purchase parts or accessories, or if you have any questions, please contact us. www.spectrumfurniture.com 800-235-1262, 715-723-6750 Thank you for purchasing Spectrum products! Assembly Tips: • Assemble the console in its final location. • To facilitate assembly, keep the fasteners finger-tight until the console is completely together.
- Page 2 Product # Description Hardware (12) 1/4-20 x 5/8” PHMS - 026064 (8) 1/4-20 Flanged locknut - 0108896 36” Corner Module (4) 1/4-20 x 15mm JC bolt - 052605 68168 (2) 2” Grommet - 039622 (2) 5/16-18 x 1” Glide - 037779 29”...
- Page 3 Assembly / Setup Corner Module Assembly Corner-to-wall filler panel Corner-to-mid-support leg and wall filler panel Corner panel Corner panel 1/4-20 x 15mm JC bolts and 1/4-20 x 15mm locknuts JC bolts Mid-support Leveler bracket Assembly tip: Do not tighten fasteners completely until the unit is together.
- Page 4 Equipment Rack Assembly 1. Tip the equipment rack onto its back. 3. Tip the unit back upright, and open the rear door to attach the (2) 2. Install the (4) glides onto the bottom as shown. The adhesive bumpers to the equipment rack frame as shown. glides can be adjusted later to level the console.
- Page 5 End-Support Leg Assembly 1. Attach the side panel to the leg frame as shown with (6) 8-32 x 3. Align the assembled end-support leg and wall filler panel mounting holes. 1/2” PH thread-cutting screws and tighten securely. Note: The 4” Be sure the wall filler panel overlaps the end-support leg as shown.
- Page 6 Mid-Support Leg Assembly Worksurfaces 1. Install the (2) glides onto the bottom of the leg. The glides can be adjusted later to level the console. 2. Align the mid-support leg and wall filler panel mounting holes as shown. 3. Attach the mid-support leg to the wall filler panels with (4) 1/4-20 x Mid-support leg 15mm JC bolts.
- Page 7 Worksurface-to-top or Equipment Rack: Worksurface-to-worksurface w/ Equipment Rack: Note: This is the attachment of a worksurface Note: This is the connection between a worksurface of equal to the top of an equipment rack. height to another worksurface above an equipment rack. 1.
- Page 8 • New logos require a first time logo charge • Includes 2” grommet • Customer-installed • Mounting plate color configured • To get panel customized-contact Spectrum for details Weight capacity: 35 lb [15.9 kg] 29”W [73.7 cm] x 15”H Dimensions: Dimensions: 21.1875”W [53.8 cm] x 30”D [76.2 cm]...
- Page 9 Elift Workstation Accent Kit - 68161 • (2) Laminate panels • Panel dims: 20”W [50.8 cm] x 27”H [68.6 cm] x .5”D [1.27 cm] • Required for acrylic logo panel • Shipping weight: 18 lb [8.17 kg] Corner Module Accent Kit (36”H) - 68161 Corner Module Accent Kit (29”H) - 68161 •...
- Page 10 P.A.C.E. program (Product Assur- ance to meet Customer Expectations). We expressly warrant that Spectrum products will be of good quality and workmanship and free from defect for the period set out in the warranty from the date of delivery.
Need help?
Do you have a question about the Elite Console 68 Series and is the answer not in the manual?
Questions and answers