INX
700 Series Probe Microscope
Quick Start Guide
Safety instruc ons
CAUTION
Turn off the equipment, and disconnect all cables
connected to it before moving the equipment or
performing maintenance procedures.
WARNING
To prevent poten al fire or shock hazard, do not expose the
·
equipment to any source of excessive moisture.
Do not perform any opera ng or maintenance procedure that is
·
not described in the user documenta on. If the equipment is
used in a manner not specified by VIAVI, the protec on
provided by the equipment might be impaired.
Do not a empt to service this product yourself, as opening or
·
removing covers might expose you to dangerous high-voltage
points and other hazards. Refer all servicing to qualified VIAVI
service personnel.
Do not operate any equipment with its covers or panels
·
removed.
AVERTISSEMENT
Pour éviter tout risque d'incendie ou d'électrocu on, n'exposez
·
pas l'équipement à une source d'humidité excessive.
N'effectuez aucune opéra on ou procédure de maintenance qui
·
n'est pas décrite dans la documenta on u lisateur. Si
l'équipement est u lisé d'une manière non spécifiée par VIAVI,
la protec on fournie par l'équipement peut être altérée.
N'essayez pas de réparer ce produit vous-même, car l'ouverture
·
ou le retrait des panneaux latéraux peut vous exposer à des
points haute tension dangereux et à d'autres dangers. Confiez
tous les travaux d'entre en au personnel de service qualifié de
VIAVI.
N'u lisez aucun équipement dont les panneaux latéraux ont été
·
re rés.
Technical Assistance Center and Knowledge Base
To find the Technical Assistance Center phone number and email in
your region for the INX 700 Series Inspec on Probe Microscope or to
search the VIAVI Solu ons Knowledge Base, visit the VIAVI Solu ons
Technical & Product Support site at
support.viavisolu ons.com
INX 700 Series Probe Microscope Quick Start Guide, 22174568 R004, January 2025
INX 700 Series Probe Microscope features
Inspec on Tip Collar
Objec ve Lens
Ac on Wheel
Inspec on Tip
Autofocus/
Inspec on Trigger
Accessory Mount
Ba ery Cover
LED states
State
LED Ring
Off
Microscope powered OFF
Ÿ
Microscope powered ON,
Ÿ
no test in progress
Orange
―
Blue
―
Purple
Test in progress
(circula ng)
Red
Test failed
Green
Test passed
Blue Orange
―
Flashing
.
1.
Power Bu on
Touchscreen
LED Ring
·
Charging LED
1.
2.
Speaker
USB-C Interface
Charging LED
3.
Microscope powered OFF
Ÿ
Ba ery charger not
Ÿ
connected
Ba ery charging,
microscope powered OFF
Microscope powered ON
―
―
By default, the system language is set to English.
Portuguese, Spanish, French, German, Simplified Chinese,
Ba ery fully charged
and Japanese are also supported.
1.
Fully discharged ba ery
charging, microscope
powered ON
2.
(Power OFF microscope
3.
un l ba ery charged)
Powering the microscope ON
Press and hold the Power bu on for two (2) seconds:
Touchscreen lights, and start-up screen appears.
Ÿ
The charging LED lights blue.
Ÿ
The Home screen appears on the touchscreen.
Ÿ
The following image shows the state of the Home
screen while an inspec on p is installed on the
microscope but no fiber is connected to the p.
While an inspec on p is installed on the
Ÿ
microscope, the fiber illumina on LED emits a
blue light from the end of the objec ve lens.
Powering the microscope OFF
Press and hold the Power bu on un l the touchscreen
turns off.
Se ng the system date and me
Power ON the microscope.
On the Home screen, select the Main Menu, select
System Se ngs, and then select Date & Time.
On the Date & Time screen, use the controls to set
the date and me op ons for the microscope, and
then select OK.
Changing the system language
On the Home screen, select the Main Menu, select
System Se ngs, and then select Language.
On the Language screen, select a language se ng.
Power the microscope OFF and then ON to apply the
new language se ng.
Page 1 of 2 (See over for Page 2)
Need help?
Do you have a question about the INX 700 Series and is the answer not in the manual?
Questions and answers