Page 1
SUPER 4000 ICE sQ AA36075 RIB يتم ضمان التشغيل الصحيح للمشغل فقط في حالة إدارته بواسطة لوحة تحكم The correct operation of the operator is guaranteed only if it is managed by a RIB control panel 3 / الصفحة العربيةENGLISH page 5...
Page 2
الحد األدنى وsqmm 1،5 معH05RN -F برقية نوعRIB 2 ° - لل قسم ونوع من النصائح الستخدام الكابالت 3° - Positioning of a possible couple of photoelectric cells: the radius of the photoelectric cells ....
Page 3
من أجل التمكن من فتح البوابة يدويا من الضروري فتح الكارتير بالمفتاح الصحيح، ثم إدخال مفتاح . في برغي الفتح وإدارته 3 مرات بعكس اتجاه عقارب الساعةRIB )آلين (مفتاح مسدس األضالع ” كام هو موضح باألسفل، ثم قمA“ قم بفتح وحدة التحريك باستخدام املقبض...
Page 4
.هام: يجب أن يتطا بق النظام مع كل ا ملعا يري والتوجيهات ا ملعمول بها حال ي ً ا .L1 لالستفادة من جميع الوظائف املتقدمة التي ميكن أن يقدمها لك مجلسRIB GATE App + مع وحداتها) واستخدام هاتفك الذيك مع تطبيقAPP (أو بطاقةAPP تنبيه: • قم بتثبيت بطاقة...
The sump with the appropriate key must be opened. below, therefore releasing the G nuts. Insert the RIB hex key in the release screw and turn it 3 times anti-clockwise. Move the mobile part manually to establish the To restore the electric functioning, operate in the opposite direction.
Page 6
IMPORTANT: The system must comply with all the standards and Directives currently in force. ATTENTION: Install the APP card (or the APP+ card with its modules) and use your smartphone with the RIB GATE App to take advantage of all the advanced features that the...
SYSTEM LAY-OUT A - SUPER 4000 operator B - Photoelectric cells (external) C - Rack D - Key selector E - Tuned aerial F - Flashing lamp H - Galvanized column for P.E. cells I - Photo electric cells (internal)
Page 8
INSTALLATION SUPER 4000 CHECKING BEFORE THE INSTALLATION !! THE GATE SHALL MOVE FRICTIONLESS !! N.B.: Gate features must be uniformed with the standards and laws in force. The door/gate can be automated only if it is in a good condition and its conditions comply with the EN 12604 norm.
ELECTRIC SAFETY DEVICES For a sliding gate weighing more than 300 kg it is obligatory to fit 2 pairs of photocells and mobile sensors in such a way as to protect any potentially dangerous openings in the gate (fig. 6). The photocells must be located at a height of between 40 cm and 60 cm. One pair of photocells must be located inside the premises and adjusted so that they cover the entire travel distance of the gate, while the other pair must be located externally between the gateposts.
ELECTRIC CONNECTIONS L1 code AC08082 Interactive online manuals...
Page 11
+ 24 Vdc accessories power supply / Common contacts RADIO Connector for radio module ACG8069 - 24 Vdc accessories power supply RADIO Connector for radio receiver RIB, 24 Vdc supply A+ TEST + 24 Vdc photocells self-test power supply 433 MHz Radio antenna COM A+ Common contacts / Positive 24 Vdc PROG.
Page 12
POINT B - SETTINGS OPEN OPEN command (NO) (green) DIP 1 MAINTENANCE CHECK (See Page 14) PROBE DIP 2 TIMES PROGRAMMING (See Point C) IS NOT AVAILABLE DIP 2-1 PROGRAMMING OF PEDESTRIAN OPENING (See Point D) DIP 1-2 SAVE/DELETE RADIO CODES FOR COMPLETE OPENING (DIP 1 ON followed by DIP 2 ON) POINT C - TIMES PROGRAMMING (POINT E) DIP 1-3...
Page 13
2 - Immediately then press the same button once on the new remote control(s) you want ALL RADIO CODES FOR TOTAL OPENING CANCELLATION PROCEDURE to register. The buzzer will sound 1 time to confirm the registration of each new remote Cancellations can only be performed when gate is stationary.
DIP 4 ON => if an obstacle is placed in range of the photocells when the gate is closed and VISUAL AND SOUND ALARMS the command to open is given, the gate opens (the photocells do not work while opening). Photocells work only during closing (with reverse motion restored after BLINKER a second, even if they are still engaged).
If the motor is working properly, check the safety devices. TROUBLE SHOOTING After having carried out all connections, by carefully following the layout and having positioned the gate in intermediate position, check the correct ignition of red LEDS DL6, DL7, DL8, DL9 and DL10.
Page 16
FAULT SOLUTION After having carried out the various connections and having supplied voltage, all the LEDS are On the board there are resettable fuses which intervene in the event of a short circuit, switched OFF. interrupting the output assigned to them. In the event of troubleshooting, it is advisable to disconnect all the removable connectors and insert them one at a time in order to more easily identify the cause of the fault.
Page 17
ACCESSORIES - For the connections and the technical data of the optional equipments follow the relevant handbooks. APP8050 APP card APP8054 APP+ card to manage the control panel using to manage the control panel using Bluetooth 4.2 transmission Bluetooth 4.2 transmission APP8064 Wi-Fi module for APP+ card APP8066 RJ45 module for APP+ card to manage the control panel using the...
Page 18
PHOTOCELLS CONNECTIONS 4 FIT SLIM / FIT SYNCRO photocells with self-test and infrared signal synchronizer 2 photocells FIT SLIM, FIT SYNCRO with self-test TX SYNCRO COM A+ COM A+ cod. ACG8028 A+ TEST A+ TEST PHOT1 PHOT2 PHOT1 PHOT2 cod. ACG8029 A*D+ A*D+ A*D+...
Page 19
CPL1022 Semiscatola inferiore CVA1300 Tappo sfiato 20x1,5 CAL1002 Piastra base Super CPL1023 Guarnizione CVA1361 Ventola motore SUPER CCA1005 Piastra rinforzo SUPER 4000 CPL1119 Ingranaggio Z22 CVA1391 Copriv. SUPER CCA1215 Protezione ingranaggio SUPER CTC1012 Chiavetta 8x7x20 CZM6008 Cuscinetto motore 6008ZZ CCU6207...
Need help?
Do you have a question about the SUPER 4000 and is the answer not in the manual?
Questions and answers