Alamo Industrial BUILT SHARPER AF60 Operator’s Manual With Parts Listing

1. PRINT FIRMLY. 2. REMOVE WHITE COPY FOR CUSTOMER RECORDS.
ALAMO INDUSTRIAL
A F
Alamo Ind. Model
Purchaser
Last Name
Street & No., RFD,
Box, &/or Apt. No.
City
Dealer
City
•
I have informed the Purchaser of this product of Warranty terms, provisions, and procedures that are applicable, reviewed the contents of the Operator's Manual
including safety equipment, safe operation, and maintenance, reviewed the Safety Signs on implement (and tractor if possible), and Purchaser's responsibility to
train his operators in safe operation.
•
IMPLEMENTS: I have explained that Deflectors, Chain Guards, or Solid Skirts must be maintained in good repair and installed except in areas where persons,
vehicles, livestock, or other property will not be endangered by thrown objects and where such safety equipment would prevent the mower's reasonable performance
of its assigned task.
•
DRIVELINES: I have made certain that all driveline, gearbox, and other shields are in good repair and fastened securely in place to prevent injuries from
entanglement or thrown objects.
•
HYDRAULIC MACHINES: I have explained the necessity of using clean hydraulic oil, changing filters as instructed, stopping leaks, damage caused by
operating with over-heated oil, caring for hoses, using hoses of proper rating, the necessity of maintaining the specified operating pressure, and the potential hazard
of oil's penetrating the skin.
•
BOOM-TYPE or FOLDING-TYPE IMPLEMENTS: I have explained that it is not possible to guard against thrown objects when the head is lifted off ground
and that operator is responsible to watch out for persons in the area. I have explained that the lifted mower head or boom can contact overhead obstructions with
damage to cables and telephone lines and possible injury. I have explained that the extended head or boom or retracted boom can contact power lines with resulting
electrocution injury or death and that operator is responsible for keeping clear of such hazards.
I have been instructed on the paragraphs above, received and have been instructed in the contents of the Operator's Manual including safety signs, safety
equipment, safe operation, maintenance, and the potential hazards of unauthorized alteration or modification of the product. I have been informed of the warranty
provisions and know that the warranty is not in effect until this form is received by Alamo Group.
I understand the Implement Guarding statements above and the potential hazards of operating without such guards. I understand that the operator is responsible for
the safety of others in the area. I have examined the product and accept it as being complete and in satisfactory condition with all required guards.
CUSTOMER COPY
Inspection Performed - Warranty and Safety Procedures Explained - Installation Complete
LUBRICATION & HYDRAULICS
o Gearbox Speed Increaser (Oil Levels)
o Hydraulic Oil Level (External. Tank)
o Tractor Hydraulic Oil Level
o Hydraulic Hoses (Not Kinked Tighten Connections)
o Front Pump Drive (Assembly Is Tight And Shaft Properly Aligned)
MOWER
o Spindle And Motor Bolts Properly Torqued
o Spindle Oil Level
o Blade Carrier Bolts Properly Torqued / Retaining Pin In Place
o Mower Cutting Height And Level Adjusted
o Belt Alignment And Tension Adjusted
o Cutting Shaft Bearings Lubricated
o All Hardware Properly Torqued
o Tire And Air Pressure / Lug Nuts (Correct Torque)
o Wheel Bearings (Check, Grease, And Preload)
ATTACHMENTS & INSTALLATION
o Deflectors Front And Rear
o Shredding Attachments
o Correct Blade Rotation Direction
o Axle Arms And Beams
o Tongue And Control Rods (Installed And Adjusted)
o All Bolts - Pins And Nuts (Proper Torque)
Purchaser's Signature _________________________ Date __________ Dealer's Signature ________________________ Date __________
3. REMOVE YELLOW COPY FOR DEALERS RECORDS.
®
WARRANTY REGISTRATION INFORMATION
Serial No.
Dealer's Signature ___________________________________ Date ______________
Purchaser's Signature ___________________________________ Date ______________
PRE-DELIVERY SERVICE
CHECK AND ADJUST OR LUBRICATE AS REQUIRED
See Operator's Manual for Details
MONTH
Purchase Date
First Name
State or
Province
State or
Province
MOWER TO TRACTOR CONNECTION
o Draw Bar Length (Check And Set)
o A-Frame Pivot & Links
o Control Rods (Adjusted Equal)
o Axle Height (Adjusted)
o Cutting Height (Adjust)
o Mount Kit Pre-Operation Check Complete
o Mower Wing (Adjust Level With The Center)
o Mower Wing (Check For Proper Raising Operation)
o C.V. Drivelines (Check Max Turn Radius)
o Pull Type Hitch (Height Adjustment)
o Mounting Hardware Properly Torqued
SAFETY ITEMS
o Protective Shields (Operation And Installation)
o Driveline Clutch (Torque Limiter) (Adjust And Run In)
o Safety Decals (Installed)
o Operator's Manual (Supplied)
o Tractor PTO Shield (Installed)
o S.M.V. Emblem (Installed If Needed)
o Neutral Safety & Cut - Off Switches
o Safety Tow Chain (Installed)
4. MAIL LAST CARD POSTAGE FREE.
DAY YEAR
M.I.
ZIP
ZIP