Advertisement
Read all safety warnings and all instructions. Make yourself familiar with the controls and the proper use of the machine. Please keep the instructions safe for later use!
General hazard safety alert. Ensure no exits are blocked or obstructed by the machine. | |
![]() | Operate the isolator switch before working on or lifting the machine. |
![]() | Do not touch rotating blades. The blades are sharp. Beware of severing toes or fingers. |
![]() | Wait until all machine components have completely stopped before touching them. The blades continue to rotate after the machine is switched off, a rotating blade can cause injury. |
![]() | Make sure that bystanders are not injured by foreign objects being thrown away. |
![]() | Keep a safe distance to the product when operating. |
![]() | Do not ride on the machine. |
![]() | Battery charger contains a safety transformer. |
![]() | Do not use a high-pressure washer or a garden hose to clean the machine. |
![]() | Carefully check the area where the tool is to be used for wildlife and pets. Wildlife and pets may be injured while the machine is in operation. Thoroughly check the working area and remove any stones, sticks, wires, bones and foreign objects. When using the machine, ensure that no wildlife, pets or small tree stumps are hidden in the dense grass. Avoid using at dusk or in the dark to reduce the risk of encountering animals. |
Turn off the product using the isolator switch:
Clean the exterior of the machine thoroughly using a soft brush and cloth. Do not use water, solvents or polishes. Remove all grass and debris, especially from the ventilation slots.
Turn the mower upside down and clean the blade area and the swivel castors regularly. Use a stiff brush or scraper to remove compacted grass clippings (see figure I).
Blades are reversible.
Do not place other objects on the mower or docking station.
It is recommended to use the original packaging when transporting the Indego over long distances.
Protect the battery against heat (e.g., against continuous intense sunlight), fire, water, and moisture. There is a risk of explosion.
The power supply is double insulated for safety and requires no earth connection. The operating voltage is 230 V AC, 50 Hz (for non-EU countries 220 V, 240 V as applicable). Contact your Bosch Service Centre for details. If in doubt contact a qualified electrician or the nearest Bosch Service Centre.
The following symbols are important for reading and understanding the operating instructions especially the diagrams. Take note of the symbols and their meaning. The correct interpretation of the symbols will help you to use the garden product in a better and safer manner.
Symbol | Meaning |
![]() | Wear protective gloves |
![]() | Permitted action |
![]() | Prohibited action |
![]() | Accessories/Spare Parts |
The mower is intended for domestic lawn mowing.
Do not operate the mower indoors.
Do not use the mower for any other purpose because of the increased risk of accidents and damage to the mower. Never attempt to modify the mower in any way since this may result in accidents or damage to the mower.
Robotic Lawnmower | SI Unit | Indego S 500 | Indego S+ 500 | Indego M 700 | Indego M+ 700 |
Article number | 3600HB02.. | 3600HB03.. | 3600HB02.. | 3600HB03.. | |
Cutting width | cm | 19 | 19 | 19 | 19 |
Height of cut | mm | 30-50 | 30-50 | 30-50 | 30-50 |
Slope angle (max.) | °/% | 15/27 | 15/27 | 15/27 | 15/27 |
Size of lawn area | |||||
– maximal | m2 | 500 | 500 | 700 | 700 |
– per charge up toA) | m2 | 70 | 70 | 85 | 85 |
Operating frequency range (Inductive sensor) | kHz | − | 5 | − | 5 |
max. magnetic field strength (Inductive sensor) (at 10 m) | dBμA/m | − | 44 | − | 44 |
Operating frequency range (GSM) | MHz | − | 880-960 | − | 880-960 |
MHz | − | 1710-1880 | − | 1710-1880 | |
Max. transmit power (GSM) | dBm | − | 33 | − | 33 |
Weight according to EPTA‑Procedure 01:2014 | kg | 7.6 | 7.7 | 7.6 | 7.7 |
Protection type | IPX4 | IPX4 | IPX4 | IPX4 | |
Serial number | see type plate on garden tool | ||||
Battery | Li-Ion | Li-Ion | Li-Ion | Li-Ion | |
Rated voltage | VDC | 18 | 18 | 18 | 18 |
Capacity | Ah | 2.5 | 2.5 | 2.5 | 2.5 |
Number of battery cells | 5 | 5 | 5 | 5 | |
Operating time, averageA) | min | 60 | 60 | 75 | 75 |
Charging period (max.) | min | 60 | 60 | 60 | 60 |
Battery type | PBA 18V...W-. 2.5 Ah | PBA 18V...W-. 2.5 Ah | PBA 18V...W-. 2.5 Ah | PBA 18V...W-. 2.5 Ah | |
Perimeter wire | |||||
– wire supplied | m | 150 | 150 | 175 | 175 |
– minimum required length | m | 20 | 20 | 20 | 20 |
– maximum permissible length | m | 350 | 350 | 350 | 350 |
Docking station | |||||
Article number | 1 600 A02 546 | 1 600 A02 546 | 1 600 A02 546 | 1 600 A02 546 | |
Input voltage | VDC | 24 | 24 | 24 | 24 |
Power consumption charging/perimeter wire switched on | W | 73/2.6 | 73/2.6 | 73/2.6 | 73/2.6 |
Charging current (up to) | A | 2.3 | 2.3 | 2.3 | 2.3 |
Allowable charging temperature rangeB) | °C | 5-45 | 5-45 | 5-45 | 5-45 |
Weight according to EPTA‑Procedure 01:2014 | kg | 1.65 | 1.65 | 1.65 | 1.65 |
Protection type | IPX4 | IPX4 | IPX4 | IPX4 | |
Power supply unit | |||||
Article number | |||||
Switzerland | F 016 L90 934 | F 016 L90 934 | F 016 L90 934 | F 016 L90 934 | |
United Kingdom | F 016 L90 935 | F 016 L90 935 | F 016 L90 935 | F 016 L90 935 | |
Rest of Europe | F 016 L90 916 | F 016 L90 916 | F 016 L90 916 | F 016 L90 916 | |
Input voltage (AC) | V | 220-240 | 220-240 | 220-240 | 220-240 |
Protection class | ![]() | ![]() | ![]() | ![]() | |
Frequency | Hz | 50-60 | 50-60 | 50-60 | 50-60 |
Output voltage (DC) | V | 24 | 24 | 24 | 24 |
Protection type | IPX7 | IPX7 | IPX7 | IPX7 | |
Weight | kg | 1.25 | 1.25 | 1.25 | 1.25 |
A) Depends on cutting height, grass conditions and moisture
B) Internal battery temperature
Noise emission values determined according to EN 50636-2-107.
Typically the A-weighted noise levels of the product are:
Sound power level 61 dB(A). Uncertainty K = 2 dB.
Action | Figure |
Accessories | A |
Delivery scope/unpacking the mower | B |
Laying out perimeter wire | C |
Extending perimeter wire | D |
Laying perimeter wire around new inner object | E |
Lifting up and carrying the mower | F |
Setting the height of cut | G |
SpotMow | H |
Cleaning | I |
Maintenance | J |
Adding a further lawn area
| K |
Replacing the battery | L |
Software update | M |
Power supply unit connection | N |
With the following QR code, you can view a video on how to install the mower under www.bosch-diy.com/indego-help. Alternatively, follow the Installation Guide delivered with the product.
Check if the perimeter wire is fully pegged to the ground avoiding any slack lengths of wire. Any loose wire can be a trip hazard.
Remove stones, loose pieces of wood, wire, live mains cables and other foreign objects from the cutting area.
Make sure that the cutting area is even and has no ditches, grooves and steep slopes above 15°/27% that are clear obstructions for the mower.
The docking station must be positioned on the wire at an outer edge of the cutting area. It may not be positioned on the side of a tool or garden shed standing as an island within the lawn to be mowed.
It is recommended that you mow your lawn once with a conventional lawnmower before installing and before the first mowing of the new season and whenever the grass clippings would be longer than 5 mm.
The mower's cutting system is designed to cut small lengths of grass (30–50 mm). The clippings can remain as mulch to fertilize the lawn. The height of cut for mower can be adjusted to 30, 40 and 50 mm.
It is recommended to start with a higher setting and then gradually decrease the height of cut as the wire disappears under the grass. This prevents your Indego from cutting the wire.
Additional perimeter wire can be added using a wire connector (see figures D–E).
The perimeter wire can be extended up to a maximum length of 350 m.
The perimeter wire can be buried up to 5 cm under the ground (or under non-metallic slabs).
To avoid causing damage to the perimeter wire, do not verticut or rake the area where it is positioned.
When laying out the wire avoid angles of less than 45°. This can affect the performance.
The display switches into sleep mode, if no input is made for 10 minutes.
(see figure K)
To install the Indego to an additional lawn area, please follow the instructions in the Installation Guide.
Separate lawn area with separate docking station (see figure K, right side): The mower can be used on up to three different lawn areas. For an additional lawn area, a separate docking station (see figure A) and the necessary perimeter wire and pegs are required. If a schedule or the "Bosch AUTO" calendar function or the Bosch "SmartMowing" functionality is set, the grass of the area it is in will be cut, within the defined time slots.
Switch off the mower when transporting it between the individual lawn areas.
Note: software updates have to be carried out on the mower in every docking station.
To ensure remembering which docking station belongs to which lawn area, it is recommended to label the docking stations with the lawn area number and description when storing them for winter.
Without separate docking station: It is possible to connect the lawn areas by placing the perimeter wire between the two lawn areas parallel to each other as close as possible (see figure K, top left). The additional lawn area without docking station is not recorded in the map memory and the mower will not use the LogiCut cutting strategy in this lawn area without the docking station. The maximum recommended lawn area without docking station is 45/50 m2 (for Indego 500/700 models). The mower will mow until it runs out of battery and will need to be carried back to the docking station for charging.
Only with Indego S 500 and M 700: After successful installation you can either immediately begin to mow by confirming "Mow now" on the display, or wait for the next scheduled cutting period, as programmed by the "Bosch AUTO" Calendar Function (previous setting required). A manual mowing schedule can also be set up according to your specific needs.
Only with Indego S+ 500 and M+ 700: After successful installation, you can begin mowing immediately by confirming "Mow now" on the display, or on the free Bosch Smart Gardening App by pressing "mow". You could also set up a programmed schedule, using the Bosch "SmartMowing" functionality, which can also plan future cutting sessions based on when it is forecasted to rain. You could also set up a programmed schedule in the calendar using the display or the Bosch Smart Gardening App.
The mower must mow a lawn area 3 times completely (do 3 full cuts) to learn the lawn area. During the learning phase, the visual result may not be optimal.
Approximate runtimes for complete lawn area coverage using LogiCut are listed below. Please note that the runtimes will vary depending on the lawn complexity and number of objects within the lawn area.
100 m2 | 4 h |
500 m2 | 16 h |
700 m2 | 22 h |
Set a schedule with frequent repetitions. This achieves good mowing results, the battery charge will last longer and you avoid debris on the lawn.
In "manual" mode, the mower works until the lawn is mowed. Mowing is interrupted only for charging the battery.
When the lawn area is mowed, the mower returns to the docking station.
In the programmable "Schedule" mode, with the "Bosch AUTO" calendar function or with the Bosch "SmartMowing" functionality, the mower operates continuously for a set period of time. Mowing is interrupted only for charging the battery. If the lawn area is mowed before the time period expires, the mower returns to the dock.
To stop mowing prematurely, press the Stop button or send the mower back to the docking station pressing the confirm button ✓.
With Indego S+ 500 and M+ 700 you can send the mower back to the docking station, by pressing the "Dock" button on the free Bosch Smart Gardening App.
The mower reduces its energy consumption by automatically switching off the power in the perimeter wire when it is not mowing and not being charged.
To wake up the mower manually from the energy saving mode, press the confirm button ✓and afterwards select either "Mow now" or another "Mowing mode", while the mower is in the docking station.
With Indego S+ 500 and M+ 700 you can wake up the mower remotely from the energy saving mode, by pressing the "mow" button on the free Bosch Smart Gardening App.
For mowing based on an active schedule or with the "Bosch AUTO" calendar function or with the Bosch "SmartMowing" functionality, the energy saving mode is automatically ended.
SpotMow is intended for mowing small areas that require special treatment without having to mow the whole lawn, such as the area under a piece of garden furniture that has been removed. The mower is positioned at the lower left corner of the intended area to mow (see figure H). The final mowed area depends on the lawn conditions; it will not necessarily be an exact square. After completion of „SpotMow", follow the instructions on the screen.
Note: For safety reasons, „SpotMow" cannot be used outside the perimeter wire.
The mower is equipped with the following sensors:
When one of the sensors is activated, e.g. the lift-up sensor, the drive motors and cutting blades are stopped. A message is indicated in the display, e.g. "lift-up".
The battery is equipped with temperature monitoring that allows charging only if the battery internal temperature is in the range between 5°C and 45°C.
The lithium-ion battery is supplied partially charged. It is recommended to charge the mower during installation of the perimeter wire in the docking station.
The lithium-ion battery can be charged at any time without reducing its service life. Interrupting the charging procedure does not damage the battery.
When the battery is run flat or discharged, the mower is shut off by means of a protective circuit: the blades no longer move.
(see figure L)
Note: The battery only needs to be replaced when it is exhausted. It is not intended to charge the battery outside the mower.
Note: Always wear protective gloves when handling or working near the sharp blades.
Switch off the mower by the isolator switch.
Remove the 5 screws of the battery compartment cover with a Torx T-20 screwdriver.
Pivot the used battery with the guide rail out of the battery compartment until the battery unlocking button can be seen and accessed. Press the battery unlocking button and remove the battery.
Insert the new battery into the guide rail until the locking mechanism can be heard to engage. Pivot back the battery with the guide rail into the battery compartment. Mount the battery compartment cover and screw it tight with the 5 screws.
The battery compartment cover protects the battery against moisture during operation.
(see figure M)
To update the software, you need a USB.org stick (FAT 32 formatted) and a USB OTG cable.
When a new software version is available, you can find it on the Internet under "www.bosch-diy.com/indego-help". Load the "IN8xxxx.bin" file onto the USB.org stick.
Turn the mower over and remove the cover from the USB port. Connect the USB OTG cable with the USB.org stick.
Place the mower in the docking station and make sure that the docking station is connected to mains (LED on docking station is on). The mower must be switched on, the display alight and the battery must be at least 70% charged.
When the update starts, the following message appears in the display "Do you want to update from version x to version y?"
Confirm by pressing the confirm button ✓. During the update, both LEDs in the mower will flash.
At the end of the update, the mower restarts.
Remove the USB OTG cable and the USB.org stick. Close the cover of the USB port.
Additionally for Indego S+ 500 and M+ 700: You can download the software via the Bosch Smart Gardening app.
The table below explains the various menu items.
Online Support
http://www.bosch-diy.com/indego-help
Problem | Possible Cause | Corrective Measure |
The LED on the docking station flashes | The perimeter wire is interrupted, too long or too short. Wire not connected and mower not in the docking station. | Check that the perimeter wire is not interrupted and is between 20 and 350 meters in length. Then switch power supply off and then on again.![]() Follow instructions in Installation Guide to install the mower. |
Excessive vibrations/noise | Blade bolt loose | Tighten blade bolt to torque of 2.5 Nm. |
Cutting blade damaged/bent | Replace cutting blade (see figure J).![]() | |
Mower not docking reliably | Perimeter wire not properly layed out around docking station | Follow instructions in Installation Guide on layout of perimeter wire. |
Perimeter wire close to a source of interference | Remove any excess (e.g. coiled up) perimeter wire around the docking station. Change perimeter wire ID in the menu. | |
Wrong docking station position setting | Change setting in the "Advanced" menu. | |
Mower fails to operate | Isolator switch not turned on | Remove mower out of docking station, turn isolator switch on and place mower back into docking station (ensure docking station is on – LED lights up green). |
Possible clogging | Always turn isolator switch off first, then check underneath the mower. Clear out as necessary (always wear protective gloves). | |
Battery not fully charged | Place mower in the docking station to allow to charge. Docking station must be on. | |
Grass too long | Mow lawn with conventional lawnmower to its lowest height-of-cut setting before using the mower. | |
Battery too hot/cold | The mower operates when the battery internal battery temperature is between 5°C – 45°C. Allow mower to cool down/warm up. If the error occurs frequently, the docking station should be positioned in the shade. | |
Mower standing on lawn with the display switched off | Operational problems | Press confirm button for screen to light up, or place mower in docking station. |
Mower does not charge | Battery too hot/cold | The mower operates when the battery internal temperature is between 5°C – 45°C. Allow mower to cool down/ warm up. If the error occurs frequently, the docking station should be positioned in the shade. |
Docking station not switched on | Switch on power supply to docking station. If docking station does not start, contact your Bosch Service Centre. | |
Charging pins corroded | Clean the charging pins. | |
Battery not fitted, incorrectly fitted or incorrect battery for mower | Insert battery correctly (see figure L). Use the appropriate Bosch battery. | |
Mower out of perimeter wire | Perimeter wire on a slope | Leave 30 cm between the perimeter wire and the slope. |
Obstacle near perimeter wire | Remove obstacle. | |
Parts of the lawn area left uncut | Mower requires more cuts to finish garden | Allow mower to run for 3 full cuts to cover whole lawn area. Alternatively use the "Intensive mode" under "Mowing mode". |
Time slot not long enough for garden size | Increase mowing time slot or:
| |
Distance between perimeter wires too small | Increase distance between the perimeter wires to a minimum of 75 cm. | |
Rough mowing conditions | Select "uneven ground/low sensitivity" option from menu item "lawn condition/bump sensor". Flatten garden/remove/bumps/mark out unsuitable areas with the perimeter wire – Please follow the instructions in the Installation Guide. | |
Grass too long | Select "uneven ground/low sensitivity" option from menu item "lawn condition/bump sensor". | |
Slopes in garden too steep | Ensure mower only operates on slopes of 15 degrees or less and full garden is not on a slope. | |
Mower gets stuck in garden | Objects/obstacles not marked out | Use the perimeter wire to mark off obstacles where the mower often gets stuck. |
Newly laid turf | Allow a few weeks for the soil to settle before using the mower. Change setting in menu item "lawn condition / bump sensor" to low sensitivity / uneven. After watering, wait as long as possible until you start the mower. | |
Mower unintentionally cuts flowers, etc. or runs over certain obstacles | Objects/obstacles below 5 cm not marked out | Mark obstacle using perimeter wire leaving 30 cm from object or remove objects/obstacles. |
Mower does not appear to cut logically | LogiCut system depends on the garden conditions. Mower does not necessarily have to continue in the next uncut area. | Further information can be found on the Installation Guide. If behaviour re-occurs often, remap garden. |
Mower does not always go in a straight line when travelling between areas | No corrective action needed. | |
Mower frequently does not find right position or turns on the spot | Change wire ID. | |
Wire crossed while marking an object | Follow instructions in the Installation Guide. | |
Mower runs in random paths in an additional lawn without docking station. | Normal behaviour. The LogiCut system only works in areas with docking station. | |
Perimeter wire keeps being cut | Wire is not taut between pegs Distance between pegs is more than 75 cm | Make wire taut and ensure distance between pegs is maximum 75 cm. Follow instructions in the Installation Guide. Use the wire connectors to repair the cut. |
Mower leaves ragged finish/poor quality of cut | The mower does not mow often enough | Mow more frequently for a good result (e.g. by means of more/longer slots in schedule). |
Cutting blades blunt | Reverse or replace cutting blades (see figure J). | |
Possible clogging | Always turn isolator switch off first, then check underneath the mower. Clear out as necessary (always wear protective gloves). | |
Perimeter wire not detected | No power at the docking station | Check if the docking station is powered up (LED is on). |
Perimeter wire damaged/cut | Check perimeter wire for damage. | |
Wrong installation (e.g. not enough distance between wires) | Follow instructions in the Installation Guide. | |
Perimeter wire close to a source of interference | Remove any excess (e.g. coiled up) perimeter wire around the docking station. Change perimeter wire ID in the menu. | |
Height-of-cut button stuck | Possible clogging | Always turn isolator switch off first, then check underneath the mower. Clear out as necessary (always wear protective gloves). |
www.bosch-garden.com
In all correspondence and spare parts orders, please always include the 10-digit article number given on the type plate of the mower.
It is possible, that the software version of your mower is required (see „Menu > Settings > Info").
If the mower is requested to be sent to the service centre, the mower and docking station must always be sent together. Do not remove the battery.
Before sending in, remove any personalised top cover that may have been fitted and any accessory cover.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch-pt.com.au
www.bosch-pt.co.nz
Robert Bosch Power Tools GmbH
70538 Stuttgart
GERMANY
www.bosch-pt.com
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Bosch Indego S 500, Indego S+ 500, Indego M 700, Indego M+ 700 Manual
Advertisement
Need help?
Do you have a question about the Indego S 500 and is the answer not in the manual?
Questions and answers