Related Manuals for Planet IFGS-620TF
Summary of Contents for Planet IFGS-620TF
- Page 1 Industrial 4-/8-port 10/100TX + 2-port 1000X SFP Ring Ethernet Switch IFGS-620TF/IFGS-624PTF/IFGS-1222TF User's Manual...
-
Page 2: Table Of Contents
Table of Contents 1. Package Contents ..................3 2. Hardware Introduction ................... 4 2.1 Switch Front Panel ................... 4 2.2 LED Definition ..................8 2.3 Switch Upper Panel ................10 2.4 Wiring the Power Inputs ................ 11 2.5 Wiring the Faulty Alarm Contact ............. 12 2.6 Grounding the Device ................ -
Page 3: Package Contents
1. Package Contents Thank you for purchasing PLANET Industrial 4-/8-port 10/100TX + 2-port 1000X SFP Ring Ethernet Switch, IFGS-620TF, IFGS-624PTF or IFGS-1222TF. The table below shows the models with the number of ports: 10/100TX 802.3at PoE 10/100/100T 1000X SFP Model Name... -
Page 4: Hardware Introduction
Switch Ring IFGS-620TF IFGS-1222TF Figure 1: IFGS-620TF/IFGS-624PTF/IFGS-1222TF Front View Ethernet Interfaces Fast Ethernet TP interfaces (Port 1 to port 4/8) 10/100BASE-TX copper, RJ45 twisted-pair: Up to 100 meters. Gigabit Ethernet TP interfaces (Port 9 to port 10) for IFGS-1222TF only 10/100/1000BASE-T copper, RJ45 twisted-pair: Up to 100 meters. - Page 5 DIP Switch The front panel of the Industrial Ring Ethernet Switch provides DIP Switch which is for configuring Ring function and PoE extension. IFGS-620TF The DIP Switch settings and descriptions: Max. Fault Alarm Loading: 24V, 1A DC Input: 9-48V , 1A max. AC Input: 24V , 0.8A max.
- Page 6 3. The active Ring function is not compatible with the IEEE 802.1p class of service function. Due to differences algorithm in design between the Industrial Ring Ethernet Switch One Key Ring and the ERPS Ring functions available on PLANET Industrial Managed Switch devices, the two functions are not compatible with each other.
- Page 7 PoE Extended Function (IFGS-624PTF Only) This mode makes the IFGS-624PTF operate on a per-port basis at 10Mbps full duplex operation but can support IEEE 802.3at PoE+ power output over a distance of up to 250 meters overcoming the 100m limit on Ethernet UTP cable. Default PoE Mode PoE+ IP Camera...
-
Page 8: Led Definition
Lights to indicate power 2 has power. Lights to indicate either power 1 or power 2 has no power. Alarm Red 10/100BASE-TX Interfaces (Port 1 to Port 4/8) (IFGS-620TF/IFGS-1222TF only) Color Function Lights to indicate the port is running at 10/100Mbps and successfully established. - Page 9 1000BASE-X Interfaces (Port 5/11 to Port 6/12) Color Function Light to indicate the port is running at 1000Mbps and successfully established. 1000 Green LNK/ACT Blinks to indicate that the switch is actively sending or receiving data over that port. ...
-
Page 10: Switch Upper Panel
, 0.8A max. 1 2 3 4 5 6 Fiber Mode Ring Switch PWR1 Alarm PWR2 Figure 3: IFGS-620TF Upper Panel Max. Fault Alarm Loading: 24V, 1A 1 2 3 4 5 6 DC Input: 12-54V , 7A max. PWR1 Alarm PWR2 Figure 4: IFGS-624PTF Upper Panel Max. -
Page 11: Wiring The Power Inputs
2.4 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of Industrial Ring Ethernet Switch is used for two redundant power inputs. Please follow the steps below to insert the power wire. When performing any of the procedures like inserting the wires or tight- ening the wire-clamp screws, make sure the power is OFF to prevent from getting an electric shock. -
Page 12: Wiring The Faulty Alarm Contact
2.5 Wiring the Faulty Alarm Contact The faulty alarm contacts are in the middle of the terminal block connector as the picture shows below. Inserting the wires, the Industrial Ring Ethernet Switch will detect the fault status of the power failure and then forms an open circuit. The following illustration shows an application example for wiring the faulty alarm contacts. -
Page 13: Installation
DIN rail and wall. Please read this chapter completely before continuing. The following pictures show how to install the device. However, the device in the picture is not Industrial Ring Ethernet Switch. 3.1 DIN-rail Mounting Installation IFGS-620TF DIN-rail Mounting Installation... -
Page 14: Wall-Mount Plate Mounting
IFGS-624PTF/IFGS-1222TF DIN-rail Mounting Installation 3.2 Wall-mount Plate Mounting 3.3 Side Wall-mount Plate Mounting You must use the screws supplied with the wall-mounting brackets. Damage caused to the parts by using incorrect screws would invalidate your warranty. -
Page 15: Product Specifications
4. Product Specifications This section describes the functionalities of the Industrial Ring Ethernet Switch’s components and guides you to installing the Switch. Model IFGS-1222TF IFGS-620TF IFGS-624PTF Hardware Specifications 8 x 10/100BASE-TX RJ45 TP Auto-MDI/ MDI-X, auto- 4 x 10/100BASE-TX RJ45 TP Auto-MDI/ negotiation... - Page 16 Provides one relay output for power failure Alarm Alarm Relay current carry ability: 1A @ DC 24V ±6KV air gap discharge ESD Protection ±6KV contact discharge Surge Immunity 6KV DC Enclosure IP30 metal case IP30 metal case IP40 metal case Installation DIN-rail kit and wall-mount ear Dimensions...
- Page 17 2 x LED for Per 4 x LED for PoE Copper Port Usage (W) (Port-9~Port-10): (Low to high): Green: LNK/ACT Amber: 30W, 60W, Amber: 1000 90W and 120W Switch Specifications Switch Processing Store-and-Forward Scheme Switch Fabric 9.6Gbps 4.8Gbps 4.8Gbps Throughput (packet per...
- Page 18 Max. Number of Class 4 PDs Standards Conformance IEEE 802.3 Ethernet 10BASE-T IEEE 802.3u Fast Ethernet 100BASE-TX IEEE 802.3ab Gigabit Ethernet 1000BASE-T (IFGS-1222TF) IEEE 802.3z Gigabit Ethernet 1000BASE-SX/LX Standards IEEE 802.3x Full-Duplex Flow Control Compliance IEEE 802.1p Class of Service (Works under Ring function disable) IEEE 802.3af Power over Ethernet (IFGS-624PTF) IEEE 802.3at Power over Ethernet Plus (IFGS-624PTF) PROFINET Traffic Pass-through with QoS...
-
Page 19: Customer Support
5. Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource on PLANET web site first to check if it could solve your issue. If you need more support information, please contact PLANET switch support team. - Page 20 FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Need help?
Do you have a question about the IFGS-620TF and is the answer not in the manual?
Questions and answers