Subscribe to Our Youtube Channel
Related Manuals for ATEN VS1818T
Summary of Contents for ATEN VS1818T
- Page 1 4/8-Port HDMI over single Cat 5 Splitter VS1814T / VS1818T User Manual www.aten.com...
-
Page 2: Fcc Information
VS1814T / VS1818T User Manual FCC Information FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 3: User Information
VS1814T / VS1818T User Manual User Information Online Registration Be sure to register your product at our online support center: International http://eservice.aten.com Telephone Support For telephone support, call this number: International 886-2-8692-6959 China 86-10-5255-0110 Japan 81-3-5615-5811 Korea 82-2-467-6789 North America... -
Page 4: Package Contents
© Copyright 2015 ATEN® International Co., Ltd. Manual Date: 2015-12-17 ATEN and the ATEN logo are registered trademarks of ATEN International Co., Ltd. All rights reserved. All other brand names and trademarks are the registered property of their respective owners. -
Page 5: Table Of Contents
VS1814T / VS1818T User Manual Contents FCC Information ..........ii RoHS. - Page 6 VS1814T / VS1818T User Manual Read Commands ........16 Baud Rate Setting Commands .
-
Page 7: About This Manual
About this Manual This User Manual is provided to help you get the most from your VS1814T / VS1818T system. It covers all aspects of installation, configuration and operation. An overview of the information found in the manual is provided below. -
Page 8: Conventions
For information about all ATEN products and how they can help you connect without limits, visit ATEN on the Web or contact an ATEN Authorized Reseller. Visit ATEN on the Web for a list of locations and telephone numbers: International http://www.aten.com... -
Page 9: Chapter 1 Introduction
You can connect up to 4 (VS1814T) or 8 (VS1818T) HDMI Receivers (such as VE812R) to a unit. The built-in RS-232 port on the VS1814T / VS1818T rear panel allows connected units to be controlled through a high-end controller or PC. -
Page 10: Features
Supports resolutions of up to Ultra HD 4kx2k and 1080p Full HD Supports up to 340MHz bandwidth for high performance video Signaling rates up to 3.4 Gbits EDID mode selection Rack-mountable * The VS1814T / VS1818T AP operation instructions can be downloaded from the ATEN website (www.aten.com). -
Page 11: Requirements
If a DVI/HDMI adapter is used. audio is not supported. 3. If you wish to utilize the VS1814T / VS1818T’s high-end serial controller function, you will also need to purchase an appropriate RS- 232 cable. See Installing the RS-232 Controller, page 12. -
Page 12: Components
Lights green to indicate that the VS1814T / VS1818T is receiving power and is up and running. Note: The VS1818T’s front panel is shown on this page. It is similar to the front panel of VS1814T except for the number of HDBaseT Out port... -
Page 13: Rear View
Note: The VS1818T’s rear panel is shown on this page. It is similar to the rear panel of VS1814T except for the number of HDBaseT Out ports – the VS1814T has 4 HDBaseT Out ports. - Page 14 VS1814T / VS1818T User Manual This Page Intentionally Left Blank...
-
Page 15: Chapter 2. Hardware Setup
3. Make sure that all devices you will be installing are properly grounded. Rack Mounting For convenience and flexibility, the VS1814T / VS1818T can be mounted on system racks. To rack mount a unit do the following: 1. Using the screws provided in the Rack Mount Kit, screw the mounting... - Page 16 VS1814T / VS1818T User Manual 2. Screw the bracket into any convenient location on the rack.
-
Page 17: Grounding
To prevent damage to your installation, it is important that all devices are properly grounded. 1. Use a grounding wire to ground the VS1814T / VS1818T by connecting one end of the wire to the grounding terminal, and the other end of the wire to a suitable grounded object. -
Page 18: Installation
HDMI source device to the VS1814T / VS1818T’s HDMI Input port. 2. Use up to 4 (VS1814T) / 8 (VS1818T) Cat 5e cables to connect up to four / eight HDMI Receiver units (i.e. VE812R) to the HDBaseT Out ports. -
Page 19: Chapter 3. Operation
Chapter 3 Operation Overview The VS1814T / VS1818T offers easy and flexible EDID learning and mode selection through pushbuttons located in the unit’s front and rear panels. EDID Learn Pushbutton The VS1814T / VS1818T can automatically learn a display’s EDID by pressing the EDID Learn Pushbutton located on the front panel. -
Page 20: Edid Mode Selection
In order to use the RS-232 serial interface to attach a high-end controller (such as a PC) to the VS1814T / VS1818T, use a serial cable such as a modem cable. The end connecting to the VS1814T / VS1818T should have a 9-pin male connector. -
Page 21: Chapter 4. Rs-232 Commands
In order to use the RS-232 serial interface to attach a high-end controller (such as a PC) to the VS1814T / VS1818T, use a serial cable such as a modem cable. The end connecting to the VS1814T / VS1818T should have a 9-pin male connector. -
Page 22: Switch Port
VS1814T / VS1818T User Manual Switch Port The available formulas for Switch Port commands are as follows: Switch Command + Output Command + Port Number + Control [Enter] 1. For example, to turn on output port 02, type the following: sw o02 on [Enter] 2. -
Page 23: Cec Commands
Chapter 4. RS-232 Commands CEC Commands Consumer Electronics Control (CEC) allows interconnected HDMI devices to communicate and respond to one remote control. The formula for CEC mode selection commands is as follows: CEC Command + Output Command + Port Number + Control [Enter] For example, to enable CEC function on output port 1, type the following: cec o01 on [Enter]... -
Page 24: Read Commands
VS1814T / VS1818T User Manual Read Commands View information from the device using the following command: Read Command + Control [Enter] The following tables show the possible values and formats for the Control command: Command Description read Reads and displays information from the VS1814T /... -
Page 25: Baud Rate Setting Commands
Chapter 4. RS-232 Commands Baud Rate Setting Commands You can set up the VS1814T / VS1818T baud rate via RS-232. The formula for Baud Rate setting commands is as follows: Baud + Baud Rate Setting value [Enter] For example, to set the baud rate to 9600, input the following:... -
Page 26: Reset Commands
VS1814T / VS1818T User Manual Reset Commands Reset the VS1814T / VS1818T to default factory settings using the following command: Reset Command [Enter] The following tables show the possible value for the Control command: Command Description reset Resets to factory default settings... -
Page 27: Appendix
Appendix Safety Instructions General Read all of these instructions. Save them for future reference. Follow all warnings and instructions marked on the device. This product is for indoor use only. Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious damage will result. - Page 28 VS1814T / VS1818T User Manual Never push objects of any kind into or through cabinet slots. They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock. Do not attempt to service the device yourself. Refer all servicing to qualified service personnel.
-
Page 29: Rack Mounting
Appendix Rack Mounting Before working on the rack, make sure that the stabilizers are secured to the rack, extended to the floor, and that the full weight of the rack rests on the floor. Install front and side stabilizers on a single rack or front stabilizers for joined multiple racks before working on the rack. -
Page 30: Technical Support
VS1814T / VS1818T User Manual Technical Support International For online technical support – including troubleshooting, documentation, and software updates: http://eservice.aten.com For telephone support, see Telephone Support, page iii: North America Email Support support@aten-usa.com Online Troubleshooting http://www.aten-usa.com/support Technical Documentation Support Software Updates... -
Page 31: Specifications
Appendix Specifications Function VS1814T VS1818T Connectors HDMI In 1 x HDMI Type A Female (Black) HDMI Out 1 x HDMI Type A Female (Black) HDBaseT Out 4 x RJ-45 Female 8 x RJ-45 Female Power Jack 1 x 3-prong AC socket... -
Page 32: Limited Warranty
VS1814T / VS1818T User Manual Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THE PRODUCT, DISK, OR ITS DOCUMENTATION.
Need help?
Do you have a question about the VS1818T and is the answer not in the manual?
Questions and answers