Related Manuals for Aethlabs microAeth AL30
Summary of Contents for Aethlabs microAeth AL30
- Page 1 AL30 ® Quick Start Guide © 2025 AethLabs microAeth AL30 Quick Start Guide AethLabs ® https://aethlabs.com Jan 2025, rev00...
- Page 2 Filter Strip Installation/Exchange To install/exchange filter strip: The model and serial number of the microAeth AL30 is located on the bottom and back of Performing Measurements the instruments adjacent to the USB-C port. Refer to the full serial number whenever you To Start Sampling and Measurements: contact AethLabs for service.
- Page 3 Important Information Before Getting Started Installation & Environmental Considerations 1) Always make sure that a filter strip is installed in the microAeth AL30 when it is The microAeth instrument is specifically designed to be used in a wide range of operating.
- Page 4 Recommendations and Best Use Practices and producing quality measurements. We recommend, at a minimum, Standard Maintenance Service at AethLabs or an authorized service center on at least an Instrument Settings: We recommend getting started using the 60 seconds timebase and annual basis.
- Page 5 7. Notification Indicator 8. Charging Indicator 9. USB-C Charging port 10. WiFi Mode button Download Quick Start Guide (download via AethLabs website) 11. 4-pin 3.3V TTL serial port 12. Filter strip release button Download Manual (download via AethLabs website) 13. Serial number label...
- Page 6 Symbol Color Illumination Description Important: Stop / Idle Mode -Always make sure that a filter strip is installed in the microAeth AL30 when it is Green & Synchronous 1 Startup - Beeping, Not collecting data until operating. & blink every 1 sec ready -Do not install previously used filter strips.
- Page 7 Filter Strip Installation/Exchange The AL30 uses the ALx Filter Strip (ALX-FS), each with 1 sampling location. Important: -Always make sure that a filter strip is installed in the microAeth AL30 when it is To Start Sampling and Measurements: operating. A) Using the front panel power button -Do not install previously used filter strips.
- Page 8 4 digits of the AL30 serial number. Example: “AL30-0001pass” automatic sampling restart ii) The unique AL30 WiFi password that the user set for the device after initial setup. Enter Default or User Set Password AL30 Quick Start Guide AL30 Quick Start Guide microAeth AethLabs microAeth AethLabs ® ®...
- Page 9 Password, the microAeth interface webpage can also be accessed over the local WiFi network as long as the “WiFi” setting in the Communications section is enabled. AL30 Quick Start Guide AL30 Quick Start Guide microAeth AethLabs microAeth AethLabs ® ®...
- Page 10 2) Automatically every 60 seconds (the hourglass icon will turn orange when a refresh will happen within the next 5 seconds). 3) When the ‘Refresh now’ button is clicked. AL30 Quick Start Guide AL30 Quick Start Guide microAeth AethLabs microAeth AethLabs ® ®...
- Page 11 (e.g. computer, tablet, phone) Associate people with AL30-<xxxx> (expandable menu item): Use this section to invite people to manage this device and view data on the AethLabs Dashboard website. • Your name: Input your name and organization to inform the invitee(s) who their invitation is from.
- Page 12 7) Click the “X” at the top right corner to close the “Data management” window. 3) The data files stored on the instrument are listed in the new window that opens. AL30 Quick Start Guide AL30 Quick Start Guide microAeth AethLabs microAeth AethLabs ® ®...
- Page 13 AethLabs MAx/ALx Series Flow Calibration Kit. Only the external mass flowmeter provided Flow Unstable measurement period. Flow deviates from in the AethLabs MAx/ALx Series Flow Calibration Kit is compatible with the AL30. target flow setpoint by more than ±5%. Optical Calibration Error...
Need help?
Do you have a question about the microAeth AL30 and is the answer not in the manual?
Questions and answers