NexiGo NXG-PS5D-0515BWHT Manual

Table of Contents

Contents

1 Product Introduction
2 Product Function and Usage Diagram
3 Product Features
4 Charging Process Instruction
5 Electrical Specifications of the Unit
6 Electrical Parameters of the Unit
7 Environment Conditions
8 Attentions
9 Contact Info
10 Documents / Resources
- 10.1 References
- 10.2 Download manual

Product Introduction

The P-5 charging station is specially designed for P-5 controllers. It can charge up to two P5 wireless controllers simultaneously. The charging indicators will turn red or green to show the charging status of controllers. It is on red when the controller is charging. and on green when it is fully charged or on standby. The top of the front panel also shows the LOGO after power on. The intelligent chip is adopted in this charging station to check the charging status. This charger comes with a special charging cable, which can provide a large-current with the input power supply of 5V/2.6A for fast charging. The brief color and aesthetic appearance also perfectly match with your P-5 console. It is a must-have for game players.

Product Function and Usage Diagram

Product Function and Usage Diagram
See Figures 1-2.

Product Features

The intel ligent micro control technology is adopted in charging indicator management;
It can charge two P-5 controllers simultaneously;
The indicator will turn red or green to show charging status. which you can know the charging state at a glance;
Aesthetic appearance with convenient placement;
Low power consumption in standby, energy saving and environment protection.

Charging Process Instruction

Plug the Type-C charging cable of this product into the Type-C power supply port on the back of the charging dock, and connect it with the back USB ports of the console or a wall charger with current and voltage at least 5V/2.6A to supply power. At this time, the LOCO in the front panel is in white. and the indicator shows red and green once respectively, then shows green pattern.
The LOCO indicator will be in white after power on, and will turn off when the power is cut off; the indicator in the middle shows the charging status of No.2 controller. and the bottom indicator shows the charging status of No.1 controller.
Refer to the attached drawing 2 of "Product Function Diagram and Usage Diagram" above, place the P 5 controller at a certain angle on the charging slot of the desktop charger for charging (note: when placing the controller, make the round rubber column on the charger align with the headphone hole of the controller, and then gently push into it).
The corresponding charging status indicator on the charging dock will be in red when the P-5 controller is undercharging; when the controller is charged up to about 90% power (about 1 hour), the indicator will turn to green, which means that the fast charging is completed; the rest 10% power will be charged by slow charging mode (about 1 hour to fully power).

Note: The indicator of the charging dock will be in green when in the slow charging mode. The orange indicator on the P-5 controller stops flashing means the controller has been fully charged. The indicator on the charging dock will briefly alternately flashes in red and green several times when the charging mode is switching.

Notice:

When the battery level of the controller reaches above 80% or more, if you remove the controller and put it back, the controller will not be charged due to the battery protection function. The dock wil continue to charge only after the battery level of the controller is below 80%.
There are specific requirements on input voltage of this product, therefore, please conntect to the back USB ports of the console or a wall charger with current and voltage at least 5V/2.6A to supply power.

Electrical Specifications of the Unit

Rated input voltage of power supply	DC 5.0V
Rated input current of power supply	2.6 A
Charging current of controllers (output current)	1000mA*2
Remarks	"*2" means that parameters of both charging channels are the same

Electrical Parameters of the Unit

Input Property
Item	Technical Parameters	Unit
Rated input voltage	5.0	Vdc
Scope of input voltage	4.75-5.60	Vdc
Rated input current	2.6	A
Maximum power consumption of standby	0.3	W
Output Property
Testing tem	Charging Current of Controllers	Unit	Remarks
Maximum charging current scope of P-5 controllers	800-1300	mA	The charging current may change in different charging stages
Charging duration of the P-5 controller	3	H	Charging to 90% by 1 hour; full charging by 2-2.5 hours

Environment Conditions

Item	Technical Indicators	Unit
Working temperature	-10~45	°C
Storage temperature	-40~70	°C
Heat-dissipating method	Natural air cooling

Attentions

The power adapter should be unplugged when the controller is fully charged or the station is not in use for a long time.
This product cannot be used and stored in a humid environment.
This product should be kept out from the dust and heavy oads to reach the maxirnum life-cycle.
Please do not use the product when it is soaked, crashed, or damaged.
Keep this product away from children.

Contact Info

Brand: NexiCo
Website: www.nexigo.com
Manufacturer: Nexight INC
Email: cs@nexigo.com
Tel: +1(458)215-6088
Address: 11075 SW 11th St Beaverton, OR 97005, US

If you have any problems please contact us at cs@nexigo.com at any time for further assistance. This product is covered by our generous 1 year manufacturers warranty, please visit www.nexigo.com for more warranty information and register on www.nexigo.com/warranty for an EXTRA ONE YEAR warranty.