Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Tormax Manuals
  4. Door Opening System
  5. iMotion 1301
  6. Installation and operating manual

Tormax iMotion 1301 Installation And Operating Manual

Swing door operator
Hide thumbs Also See for iMotion 1301:

Advertisement

Quick Links

Download this manual
Installation and Operating Manual
iMotion
TOR MAX TECHNOLOGIES, INC.
12859 Wetmore R oad
San Antonio, TX 78247
210-494-3551
210-494-5930 (FAX)
888-685-3707
WWW.TOR MAXUSA.COM
INFO@ TOR MAXUSA.COM
®
1301 Swing Door Operator
(V - 6.17)
ISSUEDATE: 09/10/10
P/N : US801279

Advertisement

loading
Need help?

Need help?

Do you have a question about the iMotion 1301 and is the answer not in the manual?

Questions and answers

Related Manuals for Tormax iMotion 1301

Summary of Contents for Tormax iMotion 1301

  • Page 1 (V - 6.17) Installation and Operating Manual iMotion ® 1301 Swing Door Operator TOR MAX TECHNOLOGIES, INC. 12859 Wetmore R oad San Antonio, TX 78247 210-494-3551 210-494-5930 (FAX) 888-685-3707 ISSUEDATE: 09/10/10 WWW.TOR MAXUSA.COM P/N : US801279 INFO@ TOR MAXUSA.COM...
  • Page 2 26 - 28 SET UP 1247 29 - 30 PRIMARY/SECONDARY APPLICATION 1319 ( SIMULTANEOUS PAIR OR DOUBLE EGRESS) PROGRAMMING TABLE 31 - 34 The companies Landert Motoren AG and Landert GmbH are cer Operating instructions iMotion 1301/ 1401 T-1305 e...
  • Page 3 Decal and walk test procedure, ask your service representative if you are not. Area of Application This document is applicable for swing doors with TORMAX automatic door operator of type: iMotion® 1301 Swing Door Operator iMotion® TN110 Swing Door Operator Explanation of Symbols In these instructions we have marked all positions which concern your safety with this symbol.
  • Page 4 Failure to do so may lead to improper use and could cause injury to persons or damage to the equipment. Tormax strongly recommends the end-user be familiar with the Daily Safety Check Decal and perform the walk test as instructed every day. If the equipment does not perform as described in the Daily Safety Check Decal turn power off to the equipment or place in P mode, immediately notify your service provider.
  • Page 5 Typical setting for normal operation. This setting allows interior, exterior activators, key switch and safety devices to operate door. Automatic 2 Mode Operates with the same characteristics as Automatic 1 O the operating cycle can be diffrent if taught in with teach in 2. Operating instructions iMotion 1301/1401 T-1305 e...
  • Page 6 AAADM daily safety check Decal, if any de ciencies are found turn the door system o and call your service provider , if no de ciencies are found the door system should now put in operation Operating instructions iMotion 1301/1401 T-1305 e...
  • Page 7 5 Trouble Shooting rror * No. Fault Reaction System Reset Frrmware incompatible to MC version /D Safety operating mode or only display eset, new version MC 32- AS Internal test negative Safety operating mode or only display eset IN to FCP 1 SIN- interrupted ast mode of operation remains Automatically if O IN to FCP 2 SIN- interrupted...
  • Page 8 6. Installation and programming T-1253 e Cable Plan 11803 Starcrest Drive Area of Application iMotion 1301 Swing Door Operator San Antonio,Tx 824 1-888-685-3 0 elease an 2009 www.tormaxusa.com c i f o i t iMotion 1301 10 A 110v AC...
  • Page 9 T-1252 e Technical Data 11803 Starcrest Drive Area of application iMotion 1301 Swing Door Operator San Antonio,Tx 824 1-888-685-3 0 elease March 2008 www.tormaxusa.com i f i o i t iMotion 1301 Swing Door Operator Operator type lectromechanical swing door operator with AC permanent magnet syn-...
  • Page 10 1-888-685-3 0 elease May 2008 www.tormaxusa.com Input / output terminal board Purpose Input, output and FCP connections for the iMotion 1301, 1401 operators and 2301, 2401 drives. 1 Inputs 2 Outputs 3 Safety sensors D I/O function 5 CAN bus...
  • Page 11 T-1360 e Module Documentation Input / Output Module MCU32-INOU-A 11803 Starcrest Drive Area of application iMotion 1301, 1401, 2301, 2401 San Antonio,Tx 824 1-888-685-3 0 elease anuary 2010 www.tormaxusa.com Input/Output terminal board Purpose Additional inputs and outputs for automatic door drives with iMotion. Not suitable for time-critical applications such as secu- rity or safety functions.
  • Page 12 Installation The module is installed on the module carrier. LIN Connection ‡ Cut to length and assemble the IN connection cable on both ends with a FCC 6-pole plug article see TO MA price list . The polarity of the FCC-plug is not of importance. T1264 6 Max 98 FCC 6 pole...
  • Page 13 T-1264 e Module Documentation Function Control Panel (FCP) MCU32-USIN-7-A 1803 Starcrest Drive Area of application iMotion 1301, 1401 Operators and 2301, 2401 Drives San Antonio, T 1-888-685-3 0 elease October 2008 www.tormaxusa.com Purpose Programming and operating the TO MA iMotion universal processor.
  • Page 14 ‡ Switch mains 115 AC ON after the functional control panel FCP is connected. LIN Connection FCC plug is polarity sensitive T1264 6 98 Max Technical Data l l u Terminal cross section 0.5 mm strand or wire 122 F Ambient Temperature 16 inch 16 inch...
  • Page 15 Purpose To manage the function of all iMotion 1301,1401swing door operators and iMotion 2301,2401 sliding door drives. Function The base module is the central functional control system of the MC 32 module family. The module contains the processor system including a non-volatile i.e.
  • Page 16 Module Connections Power supply module MC 32-PS P Potentiometer ration card (close position MC 32-CONF Indicator) Motor unit Base module T erminal module MC 32-M OT MC 32-T MC 32- AS -40-200-A rake and motor ncoder T1261 2e rake module MC 32-T Commissioning Program using FCP see T-1248...
  • Page 17 Purpose This battery backup unit is desing to be used on the iMotion 1301 Swing Door Operator only. The module is used for limited - time operation of the system a nd/or for accomplishment of a nal motion into a de- termined position.
  • Page 18 Installation The battery unit can be ins talled on the left or right hand side of the operator if header space allows. ith the provided cable, connect the battery unit with the power supply module on the control unit. connector A1 or A2 . hen connecting the batteries make sure that the polarities are not interchanged and the contacts are not short circuited A sudden discharge may cause an explosion of the batteries The constituents are highly poisonous...
  • Page 19 Out swing /Standard Preload See Page 27 19 a...
  • Page 20 Outswing / Reduced Manual Opening Force Preload ! See section 3.2 of page 27 for programming instructions ! 19 b...
  • Page 21 Inswing Application...
  • Page 22 Double Egress Application...
  • Page 23 T-1262 e Connection Diagram Terminal Module MCU32-TERM-B 11803 Starcrest Drive Area of application iMotion 1301, 1401 Swing Door Operators San Antonio, T 1-888-685-3 0 October 2008 elease www.tormaxusa.com o i t Default terminal designation. Inputs C D and utputs are progra a le see progra ing ta le or options.
  • Page 24 -1262 e Page 2 / 12 Produ er...
  • Page 25 Green Blue Yellow Black Black Brn / Wht Blk / Wht Orange T-1262 e, Page 3/12 Producer TO MA A TOMATIC 22 c...
  • Page 26 Green Blue Yellow Black Black Brn / Wht Orange Blk / Wht T-1262 e, Page 4/12 Producer TO MA A TOMATIC 22 d...
  • Page 28 Brown / White Black Orange T-1262 e, Page 6 / 12 Producer TO MA A TOMATIC 22 f...
  • Page 29 Black Yellow Green Blk / Wht Blue T-1262 e, Page / 12 Producer TO MA A TOMATIC 22 g...
  • Page 30 Black Yellow Black Green Brn / Wht Blk / Wht Blue Orange T-1262 e, Page 8 / 12 Producer TO MA A TOMATIC 22 h...
  • Page 31 Black Yellow Green Blk / Wht rown / Blue Orange T-1262 e, Page 9 / 12 Producer TO MA A TOMATIC 22 i...
  • Page 32 Black Yellow Black Green Brn / Wht Blue Orange Blk / Wht T-1262 e, page 10/12 Producer TO MA A TOMATIC 22 j...
  • Page 34 Brown / White Black Orange T-1262 e, Page 12 / 12 Producer TO MA A TOMATIC...
  • Page 35 T-1248 e Programming with Function Control Panel (FCP) 11803 Starcrest Drive Area of application iMotion 1301, 1401 Operators and 2301, 2401 Drives San Antonio, T 1-888-685-3 0 uly 2008 elease www.tormaxusa.com Contents ey 1 increase value Symbols for of code 0..9...
  • Page 36 Programming with the FCP ith key 1 the value of the number is always increased 0 to 9 and back to 0 ith key 2 the displayed number is always confirmed. Start Access Code etter C is shown Code Indication of operating mode Press keys 1 and 2 Press key 2 simultaneously until...
  • Page 37 Programming Example Disable Push n Pull feature with code 3 0 See programming table for other adjustments. xample 1 egin by entering the access code Display on FCP Pr e ss both keys simultaneously until displays, Press key 2 and will display, select will display...
  • Page 38 The area of the door leaves has to be safeguarded during the programming process. The control system uses an to indicate which program step is needed next. 11 displayed on FCP not yet programmed 1. Operator Type Code 015 for operator iMotion 1301 Swing Door Operator. T-124 e, page 1/3 Producer TO MA A TOMATIC...
  • Page 39 12 displayed on FCP not yet programmed 2. Door Leaf Weight rogram the code 0 .. and e code 0 .. Width Door corresponding value for the 27” 32” 36” 40” 44” 48” 50” 56” 60” proper estimated door `Weight Code 07 ..
  • Page 40 5. Automatic Configuration automatic configuration not yet completed nter Code 021 for the automatic con¿guration of ‡ Safety inputs A sf1, A sf2, sf3 and hen Code 021 is entered the contact type will be automatically detected NO or NC , make sure sensors are not in detection.
  • Page 41 T-1319 e Application Primary / Secondary Area of application iMotion 1301, 1401 Swing Door Operators 11803 Starcrest Drive San Antonio,Tx 824 1-888-685-3 0 elease November 2008 www.tormaxusa.com r 1401 a t l Purpose The application is suitable The purpuose of this wiring is to synchroni e the 1301 or 1401 paired operators.
  • Page 42 Commissioning and Configuration After wiring the operators, start-up the systems in the sequence described below. * See page no. 38 for Access code and Factory reset code 1. Operator type Code 015 Door leaf eight Code 0 8 Standard preload or Manual reduced Opening force See page 39 Automatic system configuration when the Code 021...
  • Page 43 05 March 2010 www.tormaxusa.com Planning, Start- p, Maintenance Function Note Door operator type iMotion 1301 Automatic configuration S 2 till 1. sign Contains 030... Start Teach-In 1 A TO 1 Start Teach-In 2 A TO 2 --Detect reference way / Delete Teach-In 1 --Detecting and storing of safety facillities 1-4 S 2 till 3.sign...
  • Page 44 Programming Table 11803 Starcrerst Dr Area of application iMotion 30 FW- ersion 06. San Antonio, T 1-888-685-3 0 Download 05 March 2010 www.tormaxusa.com Planning, Start- p, Maintenance Code Function 0...9 Speed opening / Speed limit opening imitation only valid for Teach-In 1 code degree / s 0...9...
  • Page 45 Programming Table 11803 Starcrerst Dr Area of application iMotion 30 FW- ersion 06. San Antonio, T 1-888-685-3 0 Download 05 March 2010 www.tormaxusa.com Planning, Start- p, Maintenance Code Function 1...4 Tension pwm out code in1 Operation mode OFF Contact NO. NC detect with code 038. in1 Operation mode MAN A Contact NO.
  • Page 46 Programming Table 11803 Starcrerst Dr Area of application i otion e sion San Antonio, T 1-888-685-3 0 Download 05 March 2010 www.tormaxusa.com Planning, Start- p, Maintenance Function Note I/O Module 1 out1 Mode of op. A TOMATIC 1 I/O Module 1 out1 Mode of op. A TOMATIC 2 I/O Module 1 out1 Mode of op.
  • Page 47 Your First Choice for Automatic Doors. TORMAX Sliding Doors TORMAX Swing Doors Sales, Installation and Service. Automatic and Manual Doors. T ormax Automatic 12859 etmore oad San Antonio, T 888-685-3 0 www.tormaxusa.com TO MA is a Division and a registered trademark of andert Motoren A...