CyberPower BM100 Quick Start Manual

Battery Management System Battery Management System
BP100-12VT BP100-12VT
Quick Start Guide
Typical Scenario
Connect the Battery Manager to the utility power with an AC/DC
adapter cord whose output power is more than 60W.
Special Scenario
For battery string whose total voltage is between 15V and 60V, connect
the Battery Manager to the first and last terminal of the battery string
with the included power cable (L4). (WARNING: A battery can present a
high risk of short circuit current and electrical shock. Please pay
attention to the input voltage.)
8. Press the RESTART button for one second to restart the system.
9. IP address will show on the LCD interface once the Manager is powered
and the system is initialized, or you can find it through [About →
Network info. → IPv4 address]. Use the IP address to login to the Web
Interface. The factory default Username/Password is admin/admin.
Note: Once the number of battery string and connected battery has been
changed from last configuration, please configure it via web interface
on the [Battery → Configuration], select the number of string(s) and
batteries per string, and then click Apply. Or you can reset the system
to the factory default setting via LCD interface on the [Reset/Reboot
→ Reset → Confirm].
PRODUCT CONTENTS
Battery Manager
Power Cable*
(244cm; L4)
*For 4 or less batteries per string.
Copyright © 2021 Cyber Power Systems, Inc. All rights reserved.
BM100 BM100
Battery Manager
BM100
Communication Cable (x4)
(90cm; L1)
2
INSTALLATION GUIDE
Battery #1
Battery
Manager
L3
Black Red
Ethernet
CN3
D
CN1
Probe
C
B
L1 L2
A
Red
CN4
Adapter (Typical Scenario)
AC/DC
WARNING: Highly recommended to use insulated gloves when installing
the battery probes.
1. Connect the battery connecting cable (L3) to M8 or M10 ring washers
(L5). Besides, make sure that the M8 or M10 washers (L5) are installed
above the battery series connection wire.
Note: Please see below illustration for correct installation of the two black
cables. Besides, connect the red cable to the battery pole (+).
2. Connect the cable to each Battery Probe through battery connector (CN3).
3. Fix each Battery Probe to each battery with Loop tape.
Note: When fixing the Battery Probes to the batteries, make sure it is
easy to observe the LED indicators of the Battery Probe.
4. Connect the Battery Manager's 'A' (RJ25) port to the 'Left' ('In') RJ25
port (CN1) of the first Battery Probe with the communication cable (L1).
5. Connect Battery Probes with one another through RJ25 ports (CN1) of
Battery Probes with probe communication cables (L2), and up to 120
Battery Probes in a string.
6. Connect an Ethernet cable to the Ethernet port of the Manager.
7. Provide power to the Battery Manager through an AC/DC adapter. The
required Battery Manager input voltage is 15V min, 60V max.
2 Mounting Brackets
DB9/RJ45 Communication Cable (183cm)
Battery Probe
Battery Probe
BP100-12VT
Battery Connecting Cable
(250 terminal; 30cm; L3)
WARNING: This product can expose you to chemicals including Styrene,
which is known to the State of California to cause cancer, and Bisphenol-A,
which is known to the State of California to cause birth defects or other
reproductive harm.
For more information go to www.P65Warnings.ca.gov.
Battery #2 Battery #3
L3 L3
CN3 CN3
CN1 CN1
Probe Probe
L2 L2
L4 (Special Scenario)
Pole screw
Spring washer
Washer
250 terminal of battery NTC and negative cable (L3)
Battery connector
Battery pole (-)
1
4 Bracket Mounting Screws
Probe Communication Cable
(30cm; L2)
4 Ring Washers
(M8 Ring*2, M10 Ring*2; L5)
3
Max. 120 batteries
Battery #4
L3
CN3
CN1
Probe