Download
Share
Print this page
HIKVISION DS-K1T344 Series User Manual
  1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. IP Access Controllers
  5. DS-K1T344 Series
  6. User manual
HIKVISION DS-K1T344 Series User Manual

HIKVISION DS-K1T344 Series User Manual

Face recognition terminal
Hide thumbs

Advertisement

Quick Links

Download this manual
DS-K1T344 Series Face Recognition Terminal
User Manual

Advertisement

loading
Need help?

Need help?

Do you have a question about the DS-K1T344 Series and is the answer not in the manual?

Questions and answers

Related Manuals for HIKVISION DS-K1T344 Series

Summary of Contents for HIKVISION DS-K1T344 Series

  • Page 1 DS-K1T344 Series Face Recognition Terminal User Manual...
  • Page 2 DS-K1T344 Series Face Recognition Terminal User Manual Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
  • Page 3 DS-K1T344 Series Face Recognition Terminal User Manual under the EMC Directive 2014/30/EU, RE Directive 2014/53/EU,the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points.
  • Page 4 DS-K1T344 Series Face Recognition Terminal User Manual Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Dangers and Cautions: Dangers: Neglecting any of the warnings may cause serious injury or death.
  • Page 5 DS-K1T344 Series Face Recognition Terminal User Manual 7. Improper replacement of the battery with an incorrect type may defeat a safeguard (for example, in the case of some lithium battery types). 8. Do not dispose of the battery into fire or a hot oven, or mechanically crush or cut the battery, which may result in an explosion.
  • Page 6 DS-K1T344 Series Face Recognition Terminal User Manual Improper use or replacement of the battery may result in hazard of explosion. Replace with the ● same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.
  • Page 7 DS-K1T344 Series Face Recognition Terminal User Manual Available Models Product Name Model Face Recognition Terminal DS-K1T344MBFWX-E1 DS-K1T344MFX-E1 DS-K1T344MBWX-E1 DS-K1T344MBWX-QRE1 DS-K1T344MX-E1 DS-K1T344EBFWX-E1 DS-K1T344EBWX-E1 DS-K1T344EBWX-QRE1 DS-K1T344EX-E1...
  • Page 8 DS-K1T344 Series Face Recognition Terminal User Manual Contents Chapter 1 Appearance ........................ 1 Chapter 2 Installation Description ....................3 2.1 Installing Environment ......................3 2.2 Flush Mounting with Gang Box ....................3 Chapter 3 Terminal and Wiring Description ................. 9 3.1 Wire Normal Device .......................
  • Page 9 DS-K1T344 Series Face Recognition Terminal User Manual 6.1.3 Forgot Password ......................35 6.1.4 Change Device Password .................... 35 6.2 Communication Settings ...................... 36 6.2.1 Set Wired Network Parameters .................. 36 6.2.2 Set Wi-Fi Parameters ....................38 6.2.3 Set RS-485 Parameters ....................40 6.2.4 Set Wiegand Parameters .....................
  • Page 10 DS-K1T344 Series Face Recognition Terminal User Manual 6.6.1 Enable/Disable Voice Prompt via Device ..............62 6.6.2 Set Device Time via Device ..................62 6.6.3 Set Sleep Duration via Device ..................62 6.6.4 Select Language ......................62 6.6.5 Set Device Number via Device ..................62 6.6.6 Set Privacy Parameters via Device ................
  • Page 11 DS-K1T344 Series Face Recognition Terminal User Manual 6.9.2 Theme ......................... 74 6.10 System Maintenance ......................75 6.10.1 View System Information ..................75 6.10.2 View Device Capacity via Device ................76 6.10.3 Upgrade ........................76 6.10.4 View User Manual ..................... 77 6.10.5 Restore Settings ......................
  • Page 12 DS-K1T344 Series Face Recognition Terminal User Manual 7.5.10 Set Face Parameters ....................98 7.5.11 Enable/Disable Masl Detection via Device ..............99 7.5.12 Set Privacy Parameters .................... 100 7.5.13 Set PIN Mode ......................101 7.5.14 System Upgrade & Maintenance ................101 7.5.15 View User Document ....................
  • Page 13 DS-K1T344 Series Face Recognition Terminal User Manual 8.7.5 Set Face Parameters ....................120 8.7.6 Card Settings ......................125 8.7.7 Linkage Settings ......................126 8.7.8 Set Working Mode via PC Web ................. 127 8.7.9 Privacy Settings ......................128 8.8 Call Settings ........................131 8.8.1 Device Management ....................
  • Page 14 DS-K1T344 Series Face Recognition Terminal User Manual 8.10.5 Set Prompt Schedule via PC Web ................151 8.10.6 Customize Prompt Voice via PC Web ..............153 8.10.7 Set Authentication Result Text via PC Web ............. 153 8.11 System and Maintenance ....................154 8.11.1 Reboot ........................
  • Page 15 DS-K1T344 Series Face Recognition Terminal User Manual Chapter 1 Appearance Figure 1-1 Appearance Description (Unit: mm) Note Parts of models support fingerprint function, refers to the actual product.
  • Page 16 DS-K1T344 Series Face Recognition Terminal User Manual Figure 1-2 Other Types Note For different device models, the device will support fingerprint, QR code, and keypad. Refers to actual products for details.
  • Page 17 DS-K1T344 Series Face Recognition Terminal User Manual Chapter 2 Installation Description 2.1 Installing Environment Avoid backlight, direct sunlight, and indirect sunlight. For better recognition, there should be light source in or near the installation environment. If you have to install the device outdoors, you should install a protective shield (optional) for the device.
  • Page 18 DS-K1T344 Series Face Recognition Terminal User Manual Figure 2-1 Gang Box is on Wall 2. Align the mounting plate holes with gang box holes, using 2 screws (KA4×25) to secure the mounting plate on the gang box.
  • Page 19 DS-K1T344 Series Face Recognition Terminal User Manual Figure 2-2 Secure Mounting Template 3. Complete wiring. For details, see the wiring diagram.
  • Page 20 DS-K1T344 Series Face Recognition Terminal User Manual Figure 2-3 Wiring 4. Remove screws on the back sheet, and remove the back sheet. Figure 2-4 Remove Back Sheet 5. Insert the terminals in the device. For details, see wiring diagram. Use 1 screw (KM3×8) to...
  • Page 21 DS-K1T344 Series Face Recognition Terminal User Manual Figure 2-5 Install Device 6. Arrange the cables and install the back sheet back. Apply silicone sealant among the cable wiring area to keep the raindrop from entering. Figure 2-6 Apply Silicone Sealant...
  • Page 22 DS-K1T344 Series Face Recognition Terminal User Manual 7. Complete installation. Figure 2-7 Complete Installation...
  • Page 23 DS-K1T344 Series Face Recognition Terminal User Manual Chapter 3 Terminal and Wiring Description You can connect to RS-485 card reader, door lock, exit button, door contact, alarm device, etc. via the terminals. You can connect the RS-485 terminal with the RS-485 card reader, connect the LOCK terminal with the door lock, connect the SEN and GND terminal with the door contact, the BTN/GND terminal with the exit button, and connect the Wiegand terminal with the access controller.
  • Page 24 DS-K1T344 Series Face Recognition Terminal User Manual Figure 3-1 Terminal and Wiring Description Note The wiegand interface shown in the figure is wiegand input interface, which can be connected to ● the wiegand card reader, and you need to set the wiegand transmission direction as “input”. If the device connects to the access controller, the wiegand interface is wiegand output interface, and you need to set the transmission direction as “output”.
  • Page 25 DS-K1T344 Series Face Recognition Terminal User Manual Figure 3-2 Connect the Terminals to the Interfaces Note Connect the cables according to the actual needs, and power cable must be connected. ● Supports PoE network interface, and it can be powered by PoE power supply.
  • Page 26 DS-K1T344 Series Face Recognition Terminal User Manual Note The secure door control unit should connect to an external power supply separately. The ● suggested external power supply is 12 V, 0.5 A. For scenarios with high safety requirement, use the secure door control unit wiring first. You can ●...
  • Page 27 Do not contain following characters in the password: the user name, 123, admin (case- ● insensitive), 4 or more continuously increasing or decreasing digits, or 4 or more consecutively repeated characters. Password cannot contain words such as hik, hkws, and hikvision (case insensitive). ● 3. Click Activate.
  • Page 28 DS-K1T344 Series Face Recognition Terminal User Manual 4. Edit the device IP address. You can edit the IP address via the SADP tool, the device, and the client software. 4.2 Activate via Device If the device is not activated, you can select to activate on the device after it is powered on.
  • Page 29 DS-K1T344 Series Face Recognition Terminal User Manual Figure 4-1 Activation Page Caution The password strength of the device can be automatically checked. We highly recommend you ● change the password of your own choosing (using a minimum of 8 characters, including at least...
  • Page 30 ● insensitive), 4 or more continuously increasing or decreasing digits, or 4 or more consecutively repeated characters. Password cannot contain words such as hik, hkws, and hikvision (case insensitive). ● 4.3 Activate via Web Browser You can activate the device via the web browser.
  • Page 31 Get the SADP software from the supplied disk or the official website http:// ● www.hikvision.com/en/ , and install the SADP according to the prompts. The device and the PC that runs the SADP tool should be within the same subnet.
  • Page 32 DS-K1T344 Series Face Recognition Terminal User Manual Status of the device becomes Active after successful activation. 5. Modify IP address of the device. 1) Select the device. 2) Change the device IP address to the same subnet as your computer by either modifying the IP address manually or checking Enable DHCP.
  • Page 33 DS-K1T344 Series Face Recognition Terminal User Manual Caution The password strength of the device can be automatically checked. We highly recommend you change the password of your own choosing (using a minimum of 8 characters, including at least three kinds of following categories: upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
  • Page 34 DS-K1T344 Series Face Recognition Terminal User Manual Chapter 5 Quick Operation 5.1 Set Password Change Type You can set the password change type as reserved email address or security questions. Once you forgot the device password, you can change the password via the selected change type.
  • Page 35 DS-K1T344 Series Face Recognition Terminal User Manual Figure 5-1 Select Network Note Disconnect the wired network before connecting a Wi-Fi. 2. Tap Next. Wired Network...
  • Page 36 DS-K1T344 Series Face Recognition Terminal User Manual Note Make sure the device has connected to a network. If enable DHCP, the system will assign the IP address and other parameters automatically. If disable DHCP, you should set the IP address, the subnet mask, and the gateway.
  • Page 37 DS-K1T344 Series Face Recognition Terminal User Manual Figure 5-2 Access to Hik-Connect 2. Tap Next. 3. Optional: Tap Skip to skip the step. 4. Optional: Tap Previous to go to the previous page.
  • Page 38 DS-K1T344 Series Face Recognition Terminal User Manual Note If you tap Previous to return to the Wi-Fi configuration page, you need to tap the connected Wi- Fi or connect another Wi-Fi to enter the platform page again. 5.4 Remote Operation via APP You can add the device to your mobile client for remote operation.
  • Page 39 DS-K1T344 Series Face Recognition Terminal User Manual Figure 5-3 Operate Remotely via APP 5.5 Privacy Settings You should set the privacy parameters, including the picture uploading and storage. Select parameters according to your actual needs. Upload Pic. When Auth. (Upload Captured Picture When Authenticating)
  • Page 40 DS-K1T344 Series Face Recognition Terminal User Manual Upload the pictures captured when authenticating to the platform automatically. Save Pic. When Auth. (Save Captured Picture When Authenticating) If you enable this function, you can save the picture when Authenticating to the device.
  • Page 41 DS-K1T344 Series Face Recognition Terminal User Manual Figure 5-4 Add Administrator Page 3. Select a credential to add. Note Up to one credential should be added.
  • Page 42 DS-K1T344 Series Face Recognition Terminal User Manual : Face forward at the camera. Make sure the face is in the face recognition area. Click capture and click to confirm. : Press your finger according to the instructions on the device screen. Click to confirm.
  • Page 43 DS-K1T344 Series Face Recognition Terminal User Manual Figure 5-5 Authentication Page Status Bar Instructions The device is armed/not armed.
  • Page 44 DS-K1T344 Series Face Recognition Terminal User Manual Wi-Fi is connected and signal is strong/Wi-Fi is enabled but not connected/Wi-Fi IP conflicts. Network is connected/not connected/connection error. SIP server is registered/registering failed/registered to door station but not to main station. Authentication Page Icon Note The displayed icon on the authentication page can be controlled.
  • Page 45 DS-K1T344 Series Face Recognition Terminal User Manual Chapter 6 Basic Operation 6.1 Login Login the device to set the device basic parameters. 6.1.1 Login by Activation Password You should login the system before other device operations. If you do not configure an administrator, you should follow the instructions below to login.
  • Page 46 DS-K1T344 Series Face Recognition Terminal User Manual Figure 6-1 Home Page 6.1.2 Login by Administrator If you have added an administrator for the device, only the administrator can login the device for device operation.
  • Page 47 DS-K1T344 Series Face Recognition Terminal User Manual Steps 1. Long tap on the initial page for 3 s and slide to the left/right by following the gesture to enter the admin login page. Figure 6-2 Admin Login 2. Authenticate the administrator's face, fingerprint or card to enter the home page.
  • Page 48 DS-K1T344 Series Face Recognition Terminal User Manual Figure 6-3 Home Page Note The device will be locked for 30 minutes after 5 failed fingerprint or card attempts. 3. Optional: Tap and you can enter the device activation password for login.
  • Page 49 DS-K1T344 Series Face Recognition Terminal User Manual 6.1.3 Forgot Password If you forget the password during authentication, you can change the password. Steps 1. Hold the initial page for 3 s and slide to the left/right by following the gesture and log in the page.
  • Page 50 Do not contain following characters in the password: the user name, 123, admin (case- ● insensitive), 4 or more continuously increasing or decreasing digits, or 4 or more consecutively repeated characters. Password cannot contain words such as hik, hkws, and hikvision (case insensitive). ● 5. Tap OK. 6.2 Communication Settings 6.2.1 Set Wired Network Parameters...
  • Page 51 DS-K1T344 Series Face Recognition Terminal User Manual Figure 6-4 Wired Network Settings 3. Set IP Address, Subnet Mask, and Gateway. - Enable DHCP, and the system will assign IP address, subnet mask, and gateway automatically. - Disable DHCP, and you should set the IP address, subnet mask, and gateway manually.
  • Page 52 DS-K1T344 Series Face Recognition Terminal User Manual Note The device's IP address and the computer IP address should be in the same IP segment. 4. Set the DNS parameters. You can enable Auto Obtain DNS, set the preferred DNS server and the alternate DNS server.
  • Page 53 DS-K1T344 Series Face Recognition Terminal User Manual Figure 6-5 Wi-Fi Settings 3. Enable the Wi-Fi function. 4. Configure the Wi-Fi parameters. - Select a Wi-Fi from the list, and enter the Wi-Fi's password. Tap OK. - If the target Wi-Fi is not in the list,tap Add Wi-Fi. Enter the Wi-Fi's name and password. And...
  • Page 54 DS-K1T344 Series Face Recognition Terminal User Manual Note Only digits, letters, and special characters are allowed in the password. 5. Set the Wi-Fi's parameters. - By default, DHCP is enable. The system will allocate the IP address, the subnet mask, and the gateway automatically.
  • Page 55 DS-K1T344 Series Face Recognition Terminal User Manual Note If you select Access Controller: If connect the device to a terminal via the RS-485 interface, set the RS-485 address as 2. If you connect the device to a controller, set the RS-485 address according to the door No.
  • Page 56 DS-K1T344 Series Face Recognition Terminal User Manual 6.2.5 Set ISUP Parameters Set ISUP parameters and the device can upload data via ISUP protocol. Before You Start Make sure your device has connect to a network. Steps 1. Tap System → Comm. → ISUP (Communication Settings) on the Home page to enter the settings page.
  • Page 57 DS-K1T344 Series Face Recognition Terminal User Manual Address Type Select an address type according to your actual needs. IP Address Set the ISUP server's IP address. Port No. Set the ISUP server's port No. Note Port No. Range: 0 to 65535.
  • Page 58 DS-K1T344 Series Face Recognition Terminal User Manual 6.2.7 Set AP Mode You can enable AP mode, and add the device to Hik-Connect to set network. Steps 1. Tap System Settings → Comm. (Communication Settings) on the Home page to enter the Communication Settings page.
  • Page 59 DS-K1T344 Series Face Recognition Terminal User Manual 3. Edit the employee ID.
  • Page 60 DS-K1T344 Series Face Recognition Terminal User Manual Note The employee ID should be less than 32 characters. And it can be a combination of lower ● letters, upper letters, and numbers. The employee ID should not be duplicated. ● 4. Tap the Name field and input the person name on the soft keyboard.
  • Page 61 DS-K1T344 Series Face Recognition Terminal User Manual Note The supported USB flash drive format is FAT32 or exFAT. ○ The system supports the USB flash drive with the storage of 1 G to 256 G. Make sure the free ○...
  • Page 62 DS-K1T344 Series Face Recognition Terminal User Manual 2. Tap Export Data in the Data Management page. 3. Select Person Data or Face Data. 4. Optional: Create a password for exporting. When you import those data to another device, you should enter the password.
  • Page 63 DS-K1T344 Series Face Recognition Terminal User Manual 2. Tap Person → + to enter the Add Person page. 3. Edit the employee ID. Note The employee ID should be less than 32 characters. And it can be a combination of lower ●...
  • Page 64 DS-K1T344 Series Face Recognition Terminal User Manual Figure 6-10 Add Face Picture 6. Look at the camera.
  • Page 65 DS-K1T344 Series Face Recognition Terminal User Manual Note Make sure your face picture is in the face picture outline when adding the face picture. ● Make sure the captured face picture is in good quality and is accurate. ● For details about the instructions of adding face pictures, see Tips When Collecting/ ●...
  • Page 66 DS-K1T344 Series Face Recognition Terminal User Manual Note The employee ID should be less than 32 characters. And it can be a combination of lower ● letters, upper letters, and numbers. The employee ID should not be duplicated. ● 5. Tap the Name field and input the person name on the soft keyboard.
  • Page 67 DS-K1T344 Series Face Recognition Terminal User Manual Note Numbers, upper case letters, lower case letters, and special characters are allowed in the ● person name. The suggested person name should be within 32 characters. ● 5. Tap the Fingerprint field to enter the Add Fingerprint page.
  • Page 68 DS-K1T344 Series Face Recognition Terminal User Manual Note Numbers, upper case letters, lower case letters, and special characters are allowed in the user ● name. The suggested user name should be within 32 characters. ● 5. Tap the PIN code and create a PIN for the user.
  • Page 69 DS-K1T344 Series Face Recognition Terminal User Manual Figure 6-11 Add Person 2. Tap Employee ID and you can edit the Employee ID.
  • Page 70 DS-K1T344 Series Face Recognition Terminal User Manual Note The employee ID cannot be more than 32 characters. It can be a combination of upper case letters, lower case letters, and digits. 3. Tap Name and create a name. Enter the person’s name according to the pop-up keyboard.
  • Page 71 DS-K1T344 Series Face Recognition Terminal User Manual 6.3.9 Search and Edit Person After adding the person, you can search the person and edit it. Search Person On the Person Management page, Tap the search area to enter the Search Person page. Tap Card on the left of the page and select a search type from the drop-down list.
  • Page 72 DS-K1T344 Series Face Recognition Terminal User Manual Note If you want to transfer all person information from one device (Device A) to another (Device ● B), you should export the information from Device A to the USB flash drive and then import from the USB flash drive to Device B.
  • Page 73 DS-K1T344 Series Face Recognition Terminal User Manual 6.5.1 Authenticate via Single Credential Set the user authentication type before authentication. For details, see Set Authentication Mode . Note The function are different according to different device models, refers to actual products.
  • Page 74 DS-K1T344 Series Face Recognition Terminal User Manual Note The card can be normal IC card, or encrypted card. ● If the QR Code Scanning function is enabled, you can put the QR code in front of the device ● camera to authenticate via QR code.
  • Page 75 DS-K1T344 Series Face Recognition Terminal User Manual Figure 6-12 Basic Settings Page...
  • Page 76 DS-K1T344 Series Face Recognition Terminal User Manual 6.6.1 Enable/Disable Voice Prompt via Device You can enable/disable the voice prompt function and adjust the voice volume. Login the device. For details, see Login . Tap System Settings → Basic → Sound Settings.
  • Page 77 DS-K1T344 Series Face Recognition Terminal User Manual Tap System Settings → Basic. And set Community No., Building No., and Unit No. 6.6.6 Set Privacy Parameters via Device Set the picture uploading parameters. Note Different device models support different functions. Refers to actual model.
  • Page 78 DS-K1T344 Series Face Recognition Terminal User Manual 25 frames per second. Suitable for mainland China, Hong Kong (China), the Middle East countries, Europe countries, etc. NTSC (60HZ) 30 frames per second. Suitable for the USA, Canada, Japan, Taiwan (China), Korea, the Philippines, etc.
  • Page 79 DS-K1T344 Series Face Recognition Terminal User Manual Figure 6-13 Face Settings 6.7.1 Set Face Liveness Level via Device After enabling face anti-spoofing function, you can set the matching security level when performing live face authentication.
  • Page 80 DS-K1T344 Series Face Recognition Terminal User Manual Login the device. For details, see . Tap System → Biometrics. Select a face liveness level. You can select from general, advanced, and professional. The higher the level, the fault acceptance rate will be lower and the false rejection rate will be higher.
  • Page 81 DS-K1T344 Series Face Recognition Terminal User Manual Set the matching threshold when authenticating via 1:1 matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. The maximum value is 100. 6.7.6 Enable/Disable ECO Mode via Device If the ECO mode is enabled, you can authenticate faces in the low light or dark environment with IR camera.
  • Page 82 DS-K1T344 Series Face Recognition Terminal User Manual Set face with mask 1:N matching threshold. The larger the value, the smaller the false accept rate and the larger the false rejection rate. The maximum value is 100. ECO Mode (1:1) Threshold After enabling the ECO mode, you can set the face with mask function.
  • Page 83 DS-K1T344 Series Face Recognition Terminal User Manual Figure 6-14 Access Control Settings 6.8.1 Set Terminal Authentication Mode via Device Select the face recognition terminal's authentication mode. You can select different combination to authenticate. Login the device. For details, see Login .
  • Page 84 DS-K1T344 Series Face Recognition Terminal User Manual If all persons on the device’s authentication mode is Device Mode, all persons on the device will use the device authentication mode. For detail about person authentication mode settings, see Set Authentication Mode .
  • Page 85 DS-K1T344 Series Face Recognition Terminal User Manual 6.8.4 Enable/Disable M1 Card Enable or disable M1 card function. Login the device. For details, see Login . After login, tap ACS. Tap Enable M1 Card, and the device can read M1 card.
  • Page 86 DS-K1T344 Series Face Recognition Terminal User Manual The PIN is set on the device or PC Web. 4. Go back to the previous page to save the settings. 6.8.8 Set Door Contact via Device Select door contact status according to the door contact’s wiring method.
  • Page 87 DS-K1T344 Series Face Recognition Terminal User Manual Figure 6-15 Preference Settings 6.9.1 Set Shortcut Key via Device Choose the shortcut key that displayed on the authentication page, including the QR code function, the call function, call type, and the password entering function.
  • Page 88 DS-K1T344 Series Face Recognition Terminal User Manual Figure 6-16 Shortcut Key Settings Password Enable this function and you can enter the password to authenticate via password. Tap the authentication page to verify. QR Code You can use the QR code scanning function on the authentication interface. The device will upload the information associated with the obtained QR code to the platform.
  • Page 89 DS-K1T344 Series Face Recognition Terminal User Manual Login the device. For details, see . Tap System → Preference → Theme Mode. Select a theme mode. Authentication The live view will be displayed in authentication, and in the meanwhile, the person's name, employee ID, face pictures will all displayed as well.
  • Page 90 DS-K1T344 Series Face Recognition Terminal User Manual After enabling this function, the device will lock automatically when anti-spoofing detection failed. Locking Duration Set the lock duration after enabling Lock Face for Anti-Spoofing Protection when anti- spoofing detection failed. Version Information You can view the device version.
  • Page 91 DS-K1T344 Series Face Recognition Terminal User Manual 6.10.4 View User Manual You can view the QR code of the user manual. Tap System Maintenance → User Manual , scan the QR code to view the user manual. 6.10.5 Restore Settings Restore to Factory Settings via Device All parameters will be restored to the factory settings.
  • Page 92 DS-K1T344 Series Face Recognition Terminal User Manual 6.11.1 Call Client Software from Device Steps 1. Get the client software from the supplied disk or the official website, and install the software according to the prompts. 2. Run the client software and the control panel of the software pops up.
  • Page 93 DS-K1T344 Series Face Recognition Terminal User Manual Note The device will call the main station in priority. 6.11.3 Call Device from Client Software Steps 1. Get the client software from the supplied disk or the official website, and install the software according to the prompts.
  • Page 94 DS-K1T344 Series Face Recognition Terminal User Manual 6.11.5 Call Mobile Client from Device Steps 1. Get the mobile mobile client from the supplied disk or the official website, and install the software according to the prompts. 2. Run the mobile client and add the device to the mobile client.
  • Page 95 DS-K1T344 Series Face Recognition Terminal User Manual Chapter 7 Configure Device via Mobile Web 7.1 Login You can login via mobile browser. Note Make sure the device is activated. For details, see . ● Enable the device Wi-Fi function and set an IP for the device. Make sure the device and the ●...
  • Page 96 DS-K1T344 Series Face Recognition Terminal User Manual Steps Note Only the device and the phone are in the same LAN, can you see the settings. 1. Tap → User Management → → Account Security Settings. 2. Select a password reset method and start to edit.
  • Page 97 DS-K1T344 Series Face Recognition Terminal User Manual 7.5.2 Set Device Time Set the time zone of the device and the device current time. → System Settings → Time Settings. Figure 7-1 Time Settings Time Zone Tap to select a time zone for the device.
  • Page 98 DS-K1T344 Series Face Recognition Terminal User Manual 7.5.4 Network Settings Set Wired Network Parameters Set wired network parameters of the device. Before You Start The device is connected to a wired network. Steps 1. On the home page, tap → Communication Settings → TCP/IP .
  • Page 99 DS-K1T344 Series Face Recognition Terminal User Manual 2) Tap WLAN Settings. 3) Set the WLAN parameters. Enable DHCP Enable DHCP to Auto DNS, the device will allocate the IP and DNS automatically. Disable DHCP Manually set the IP and DNS server.
  • Page 100 DS-K1T344 Series Face Recognition Terminal User Manual Cloud Service Accessing The device can communicate via cloud service. You can add the device to mobile client and operate. Steps 1. Tap → Device Access → Hik-Connect → Guarding Vision . 2. Check Enable.
  • Page 101 DS-K1T344 Series Face Recognition Terminal User Manual Figure 7-2 ISUP Settings Page Set OTAP Protocol You can access the device to the maintenance platform by OTAP protocol to realize searching and gaining device information, uploading device running status and exceptions, rebooting and upgrading.
  • Page 102 DS-K1T344 Series Face Recognition Terminal User Manual Figure 7-3 OTAP 2. Slide Enable. 3. Set server address, port, device ID and encryption key. 4. Tap Test, and make sure the device can connect to the server and registration completed. 5. Tap Save.
  • Page 103 DS-K1T344 Series Face Recognition Terminal User Manual Create person employee ID, name, floor No., and room No. Tap Save. Set Person Permission → Person Management → +. Enable Long-Term Effective User and set the start time and end time of the person.
  • Page 104 DS-K1T344 Series Face Recognition Terminal User Manual or edited on the device or on the web, and cannot be set on other platforms; If it is a platform- applied personal PIN, it can be created or edited on the platform, and issued to the device before it can be used.
  • Page 105 DS-K1T344 Series Face Recognition Terminal User Manual When the terminal is online, it will display the terminal's model, or it will display offline. (Read-only) Enable Authentication Device If enable the function, you can authenticate credential on the terminal; or you cannot use credential to authenticate.
  • Page 106 DS-K1T344 Series Face Recognition Terminal User Manual Terminal Model When the terminal is online, it will display the terminal's model, or it will display offline. (Read-only) Enable Authentication Device If enable the function, you can authenticate credential on the terminal; or you cannot use credential to authenticate.
  • Page 107 DS-K1T344 Series Face Recognition Terminal User Manual Set Door Parameters Set door parameters, including door name, open duration, exit button type, door remain open duration with first person, door open timeout alarm, door contact, extended open duration, duress code, super password.
  • Page 108 DS-K1T344 Series Face Recognition Terminal User Manual Set Terminal Parameters You can set terminal parameters for accessing. → Access Control → Terminal Parameters. Working Mode You can set Working Mode as Access Control Mode. Access Control Mode The access control mode is the device normal mode. You should authenticate your credential for accessing.
  • Page 109 DS-K1T344 Series Face Recognition Terminal User Manual Set the output type according to your actual needs. Set Card Security Set the device card parameters. → 禁配置 → 卡片安全。 在手机网 端主 点 配置卡片相关参数，点 保存。 Enable NFC Card The device can read NFC card. If the data of access control devices is obtained by mobile devices, the situation of unauthenticated access may occur.
  • Page 110 DS-K1T344 Series Face Recognition Terminal User Manual 7.5.9 Video Intercom Settings Set Device No. via Mobile Web The device can be used as access control device, door station, or outer door station. You can set the device number for video intercom.
  • Page 111 DS-K1T344 Series Face Recognition Terminal User Manual Customize device No. Note If the device type is Outer Door Station, the No. should be between 1 and 99. ● After changing the device type or No., you should reboot the device to take effect.
  • Page 112 DS-K1T344 Series Face Recognition Terminal User Manual Number Settings Set SIP number for the room. The rooms can communicate with each other via SIP number. Steps 1. Tap → Intercom → Number Settings. 2. Enter Room No. and SIP Number1.
  • Page 113 DS-K1T344 Series Face Recognition Terminal User Manual Face 1:N Security Level Set the matching threshold when authenticating via 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. The maximum value is 100.
  • Page 114 DS-K1T344 Series Face Recognition Terminal User Manual Set None、Reminder of Wearing, and Must Wear. None If the person do not wear a face mask when authenticating, the device will not prompt a notification. Reminder of Wearing Face Mask If the person do not wear a face mask when authenticating, the device prompts a notification and the door will open.
  • Page 115 DS-K1T344 Series Face Recognition Terminal User Manual 7.5.13 Set PIN Mode Make sure the PIN is platform-applied personal PIN or device-set personal PIN before settings. If it is a device-set personal PIN, it can be created or edited on the device or on the web, and cannot be set on other platforms;...
  • Page 116 DS-K1T344 Series Face Recognition Terminal User Manual 7.5.15 View User Document View the user document. Note Only when you enter the mobile web by IP address, can you view the user document. Login by hot spot does not support the function.
  • Page 117 Answer the security questions. E-mail Verification 1. Export the QR code and send it to pw_recovery@hikvision.com as attachment. 2. You will receive a verification code within 5 minutes in your reserved email. 3. Enter the verification code into the verification code field to verify your identification.
  • Page 118 DS-K1T344 Series Face Recognition Terminal User Manual 8.3.2 View Online Help Document You can view the help document for Web configuration. Click → Online Document on the upper right of the Web page to view the document. 8.4 Logout Log out the account.
  • Page 119 DS-K1T344 Series Face Recognition Terminal User Manual 8.5.2 Select Language You can select a language for the device system. Click in the top right of the web page to enter the Device Language Settings page. You can select a language for the device system from the drop-down list.
  • Page 120 DS-K1T344 Series Face Recognition Terminal User Manual Figure 8-2 Privacy Settings Picture Uploading and Storage Save Picture When Authenticating Save picture when authenticating automatically. Upload Picture When Authenticating Upload the pictures when authenticating to the platform automatically. Save Registered Picture The registered face picture will be saved to the system if you enable the function.
  • Page 121 DS-K1T344 Series Face Recognition Terminal User Manual Note The uploaded picture should be within 200 K, in JPG、JPEG、PNG format. 2) Click Add Card to enter the Card No. and select the property of the card. Note Up to 5 cards can be supported.
  • Page 122 DS-K1T344 Series Face Recognition Terminal User Manual Note The main door station No. is 0, and the sub door station No. ranges from 1 to 16. Outer Door Station No. Set the device installed outer door station No. Note The No. ranges from 1 to 99.
  • Page 123 DS-K1T344 Series Face Recognition Terminal User Manual Enable Long-Term Effective User, or set Long-Term Effective User, and the person can only has the permission within the configured time period according to your actual needs. Set the door permission. Click Save to save the settings.
  • Page 124 DS-K1T344 Series Face Recognition Terminal User Manual Authentication Settings Click Person Management → Add to enter the Add Person page. Set the authentication type. Click Save to save the settings. Delete Person On the person management page, check the person need to delete and click Delete.
  • Page 125 DS-K1T344 Series Face Recognition Terminal User Manual Figure 8-3 Live View Page Function Descriptions: Door Status Click on the video to view the device live video. Set the volume when starting live view. Note If you adjust the volume when starting two-way audio, you may hear a repeated sounds.
  • Page 126 DS-K1T344 Series Face Recognition Terminal User Manual Select the streaming type when starting live view. You can select from the main stream, sub stream or third stream. Full screen view. Controlled Status You can control the door to be opened, closed, remaining open or remaining closed according to your actual needs.
  • Page 127 DS-K1T344 Series Face Recognition Terminal User Manual Figure 8-4 Search Event Enter the search conditions, including the event type, the employee ID, the name, the card No., the start time, and the end time, and click Search. The results will be displayed on the right panel.
  • Page 128 DS-K1T344 Series Face Recognition Terminal User Manual Click Access Control → Parameter Settings → Door Parameters to enter the settings page. Set the open duration, that is the action time after the door is unlocked. If the door is not opened within the set time, the door will automatically lock.
  • Page 129 DS-K1T344 Series Face Recognition Terminal User Manual Set Extended Open Duration via PC Web The door contact can be enabled with appropriate delay after person with extended access needs swipes her/his card. Click Access Control → Parameter Settings → Door Parameters to enter the settings page.
  • Page 130 DS-K1T344 Series Face Recognition Terminal User Manual 8.7.4 Authentication Settings Figure 8-5 Authentication Settings Select Main or Sub Card Reader via PC Web Set the terminal for person authentication. Click Access Control → Parameter Settings → Authentication Settings to enter the settings page.
  • Page 131 DS-K1T344 Series Face Recognition Terminal User Manual Enable Authentication Device via PC Web After enabling, the authentication terminal can be used for card swiping. Steps 1. Click Access Control → Parameter Settings → Authentication Settings to enter the settings page.
  • Page 132 DS-K1T344 Series Face Recognition Terminal User Manual Click Access Control → Parameter Settings → Authentication Settings to enter the settings page. When you select the terminal as main or sub card reader, slide to enable Alarm of Max. Failed Attempts, and set Max. Authentication Failed Attempts.
  • Page 133 DS-K1T344 Series Face Recognition Terminal User Manual Set Timeout Duration of Entering Password via Web Client Set the maximum interval of entering two characters of the password. After entering one character, if the next character is not entered within the set interval, the entered characters will all be automatically cleared.
  • Page 134 DS-K1T344 Series Face Recognition Terminal User Manual 8.7.5 Set Face Parameters Figure 8-6 Set Face Parameters Enable/Disable Face Anti-spoofing via Web Browser When enabled, the device can recognize whether the person is a live one or not. Click Access Control → Parameter Settings → Smart to enter the settings page.
  • Page 135 DS-K1T344 Series Face Recognition Terminal User Manual Enable or disable the live face detection function. When enabled, the device can recognize whether the person is a live one or not. If the face is not a live one, authentication will fail.
  • Page 136 DS-K1T344 Series Face Recognition Terminal User Manual Set Face Picture Quality Grade for Applying via PC Web The grade for face authentication needs to be higher than the threshold to be successful. Click Access Control → Parameter Settings → Smart to enter the settings page.
  • Page 137 DS-K1T344 Series Face Recognition Terminal User Manual Set Face Recognition Timeout Value Configure the timeout period for face recognition. If the face recognition time exceeds the configured value, the device will prompt the face recognition timeout. Click Access Control → Parameter Settings → Smart to enter the settings page.
  • Page 138 DS-K1T344 Series Face Recognition Terminal User Manual Set the matching threshold when authenticating via ECO mode 1:N matching mode. The larger the value, the smaller the false accept rate and the larger the false rejection rate. The maximum value is 100.
  • Page 139 DS-K1T344 Series Face Recognition Terminal User Manual 8.7.6 Card Settings Enable/Disable NFC Protection via PC Web After enabling, the device can read NFC card. Click Access Control → Parameter Settings → Card Settings to enter the settings page. Click to Enable NFC Card and click Save. After enabling, the device can read NFC card. If the data of access control devices is obtained by mobile devices, the situation of unauthenticated access may occur.
  • Page 140 DS-K1T344 Series Face Recognition Terminal User Manual Enable/Disable CPU Card via Web Client After enabling, the device can recognize CPU card and users can swipe CPU card via the device. Click Access Control → Parameter Settings → Card Settings to enter the settings page.
  • Page 141 DS-K1T344 Series Face Recognition Terminal User Manual Figure 8-7 Linkage Settings 2. Click + . 3. Set event source. Select the linkage type as Event Linkage, Card Linkage or Link Employee ID. - Select Linkage Type as Event Linkage, you can select event types according to your actual needs.
  • Page 142 DS-K1T344 Series Face Recognition Terminal User Manual You can set the working mode as access control mode. Access Control Mode The access control mode is the device normal mode. You should authenticate your credential for accessing. 8.7.9 Privacy Settings Figure 8-8 Privacy Settings...
  • Page 143 DS-K1T344 Series Face Recognition Terminal User Manual Set Event Storage Type via PC Web Browser You can configure the event storage type. Click Access Control → Parameter Settings → Privacy Settings to enter the settings page. You can select Event Storage Type as Delete Old Events Periodically, Delete Old Events by Specified Time or Overwriting.
  • Page 144 DS-K1T344 Series Face Recognition Terminal User Manual Save Registered Picture The registered face picture will be saved to the system if you enable the function. Save Pic. After Linked Capture If you enable this function, the captured pictures will be saved to the device automatically.
  • Page 145 DS-K1T344 Series Face Recognition Terminal User Manual 8.8 Call Settings 8.8.1 Device Management You can view the device No., type, IP, serial No., model, version, floor No., room No., No., arming status, user name, network status and operation. You can also add indoor station and sub door station on the device management page, and manage, upgrade or delete devices.
  • Page 146 DS-K1T344 Series Face Recognition Terminal User Manual Figure 8-9 Device No. Settings If set the device type as Door Station, you can set the Floor No., Door Station No., Community No., Building No., and Unit No. Device Type The device can be used as a door station or outer door station. Select a device type from the drop-down list.
  • Page 147 DS-K1T344 Series Face Recognition Terminal User Manual Note If you change the No., you should reboot the device. Click Save to save the settings after the configuration. If set the device type as Outer Door Station, you can set outer door station No., and community Outer Door Station No.
  • Page 148 DS-K1T344 Series Face Recognition Terminal User Manual Figure 8-10 Video Intercom Network After configuration, you can achieve communication between access control devices and video intercom door station, indoor station, main station, platforms, etc. Click Save. 8.8.4 Set Communication Time via PC Web Set the max.
  • Page 149 DS-K1T344 Series Face Recognition Terminal User Manual 3. Enable Link Authentication to Call according to your needs. After enabled, when person passes authentication, the door will be remotely opened by the target that is configured with button for automatic calling.
  • Page 150 DS-K1T344 Series Face Recognition Terminal User Manual Click System and Maintenance → System Configuration → System → System Settings → Time Settings . Figure 8-13 Time Settings Click Save to save the settings after the configuration. Time Zone Select the device located time zone from the drop-down list.
  • Page 151 DS-K1T344 Series Face Recognition Terminal User Manual 8.9.3 Change Administrator's Password Steps 1. Click System and Maintenance → System Configuration → System → User Management → User Management . 2. Click 3. Enter the old password and create a new password.
  • Page 152 DS-K1T344 Series Face Recognition Terminal User Manual 8.9.6 Network Settings Set Basic Network Parameters via PC Web Click System and Maintenance → System Configuration → Network → Network Settings → TCP/IP . Figure 8-14 TCP/IP Settings Page Set the parameters and click Save to save the settings.
  • Page 153 DS-K1T344 Series Face Recognition Terminal User Manual DHCP If uncheck the function, you should set the IPv4 address, IPv4 subnet mask, IPv4 default gateway, Mac address, and MTU. If you check the function, the system will allocate the IPv4 address, IPv4 subnet mask, the IPv4 default gateway automatically.
  • Page 154 DS-K1T344 Series Face Recognition Terminal User Manual 5. Click Save. Set Device Hotspot After enabling the device hotspot, you can use the mobile phone to connect the hotspot and set. Go to System and Maintenance → System Configuration → Network → Network Settings →...
  • Page 155 DS-K1T344 Series Face Recognition Terminal User Manual View the Port. Set WebSocket(s) via PC Web View WebSocket and WebSockets port. Go to System and Maintenance → System Configuration → Network → Network Service → WebSocket(s) . View WebSocket and WebSockets port.
  • Page 156 DS-K1T344 Series Face Recognition Terminal User Manual Figure 8-16 Set OTAP 2. Click to Enable OTAP. 3. Set Server IP Address, Port, Device ID and Encryption Key. 4. Click Test to ensure the device can connect to the server and register successfully. Refresh the page or restart the device to see the Register Status.
  • Page 157 DS-K1T344 Series Face Recognition Terminal User Manual Note 8 to 32 letters (a to z, A to Z) or numbers (0 to 9), case sensitive. You are recommended to use a combination of no less than 8 letters or numbers.
  • Page 158 DS-K1T344 Series Face Recognition Terminal User Manual The device displayed call number and user name. 4. Click Save. 8.9.7 Set Video and Audio Parameters via PC Web Configure Video Parameters via Web Browser You can set quality, resolution and other parameters of device camera.
  • Page 159 DS-K1T344 Series Face Recognition Terminal User Manual 8.9.8 Image Parameter Settings Figure 8-19 Display Settings Figure 8-20 OSD Settings...
  • Page 160 DS-K1T344 Series Face Recognition Terminal User Manual Set Brightness/Contrast/Saturation/Sharpness via PC Web You can set picture information such as brightness, contrast, saturation and sharpness of live view page. Click System and Maintenance → System Configuration → Image → Display Settings to enter the settings page.
  • Page 161 DS-K1T344 Series Face Recognition Terminal User Manual 8.9.9 Alarm Settings via PC Web Set the alarm output parameters. Steps 1. Click System and Maintenance → System Configuration → Event → Alarm Settings → Alarm Output . 2. Set Alarm Name and mode of Alarm Duration.
  • Page 162 DS-K1T344 Series Face Recognition Terminal User Manual Note After the peripheral is changed and saved, the device will reboot automatically. RS-485 Address Set the RS-485 Address according to your actual needs. Note If you select Access Controller: If connect the device to a terminal via the RS-485 interface, set the RS-485 address as 2.
  • Page 163 DS-K1T344 Series Face Recognition Terminal User Manual Note If you change the peripheral, and after you save the device parameters, the device will reboot automatically. 8.10 Preference Settings 8.10.1 Set Standby Image via PC Web Set the standby image parameters, including the time to enter standby, and sleep time.
  • Page 164 DS-K1T344 Series Face Recognition Terminal User Manual 8.10.3 Customize Authentication Desk via PC Web Customize the modules on the authentication page/desk. Steps 1. Go to System and Maintenance → Preference → Custom Home Page. 2. Select Application Mode. Figure 8-25 Select Application Mode...
  • Page 165 DS-K1T344 Series Face Recognition Terminal User Manual Figure 8-26 Notice Publication Material Management You can click + Add Theme, and set Theme Name and Theme Type. Click Upload, and click + to upload the picture or video from the local PC.
  • Page 166 DS-K1T344 Series Face Recognition Terminal User Manual Figure 8-27 Prompt Schedule 2. Enable the function. 3. Set the appellation. 4. Select time schedule. 5. Set the time period when authentication succeeded. 1) Click Add Time Duration. 2) Set the time duration.
  • Page 167 DS-K1T344 Series Face Recognition Terminal User Manual Note If authentication is failed in the configured time duration, the device will broadcast the configured content. 3) Set the audio content. 4) Optional: Repeat substep 1 to 3. 5) Optional: Click to delete the configured time duration.
  • Page 168 DS-K1T344 Series Face Recognition Terminal User Manual Figure 8-29 Authentication Result Text 2. Enable Customize Authentication Result Text. 3. Enter custom texts. 4. Click Save. 8.11 System and Maintenance 8.11.1 Reboot You can reboot the device. Click System and Maintenance → Maintenance → Restart to enter the settings page.
  • Page 169 DS-K1T344 Series Face Recognition Terminal User Manual If the device is connected to the network and added to Hik-Connect App, you can tap Device Upgrade → Online Upgrade on device for upgrading when there is an updated version in Hik- Connect App.
  • Page 170 DS-K1T344 Series Face Recognition Terminal User Manual 8.11.6 Device Debugging You can set device debugging parameters. Enable/Disable SSH via Web Browser You can enable SSH to perform remote debugging. Click System and Maintenance → Maintenance → Device Debugging → Log for Debugging.
  • Page 171 DS-K1T344 Series Face Recognition Terminal User Manual Figure 8-30 Protocol Testing Select a protocol address, and enter the protocol. Click Execute. Debug the device according to the response header and returned value. 8.11.7 View Log via PC Web You can search and view the device logs.
  • Page 172 DS-K1T344 Series Face Recognition Terminal User Manual Enable Lock Face for Authentication, and set Lock Duration. The face will be locked for the set lock duration after the failed attempt limit of anti-spoofing detection has been reached. Click Save. Version Information You can view the different version information here.
  • Page 173 DS-K1T344 Series Face Recognition Terminal User Manual 2) Select a certificate type in the Import Communication Certificate area, and select a certificate from the local, and click Import. Import Other Authorized Certificate If you already has an authorized certificate (not created by the device), you can import it to the device directly.
  • Page 174 DS-K1T344 Series Face Recognition Terminal User Manual Appendix A. Tips for Scanning Fingerprint Recommended Finger Forefinger, middle finger or the third finger. Correct Scanning The figure displayed below is the correct way to scan your finger: You should press your finger on the scanner horizontally. The center of your scanned finger should align with the scanner center.
  • Page 175 DS-K1T344 Series Face Recognition Terminal User Manual Environment The scanner should avoid direct sun light, high temperature, humid conditions and rain. When it is dry, the scanner may not recognize your fingerprint successfully. You can blow your finger and scan again.
  • Page 176 DS-K1T344 Series Face Recognition Terminal User Manual Appendix B. Tips When Collecting/Comparing Face Picture The position when collecting or comparing face picture is as below: Positions (Recommended Distance: 0.5 m) Expression Keep your expression naturally when collecting or comparing face pictures, just like the ●...
  • Page 177 DS-K1T344 Series Face Recognition Terminal User Manual Size Make sure your face is in the middle of the collecting window.
  • Page 178 DS-K1T344 Series Face Recognition Terminal User Manual Appendix C. Tips for Installation Environment 1. Light Source Illumination Reference Value Candle: 10Lux Bulb: 100~850Lux Sunlight: More than 1200Lux 2. Avoid backlight, direct and indirect sunlight...
  • Page 179 DS-K1T344 Series Face Recognition Terminal User Manual Appendix D. Dimension Figure D-1 Dimension (Unit: mm)
  • Page 180 ● Products described in this Document, which may include licenses obtained from third parties. Any part of the Document, including text, pictures, graphics, etc., belongs to Hikvision. No part ● of this Document may be excerpted, copied, translated, or modified in whole or in part by any means without written permission.
  • Page 181 LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY ●...
  • Page 182 DS-K1T344 Series Face Recognition Terminal User Manual Appendix F. Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a hazardous situation which, if not avoided, will or could Danger result in death or serious injury.
  • Page 183 UD37803B...

This manual is also suitable for:

Ds-kit344mbfwx-e1Ds-kit344mfx-e1Ds-kit344mbwx-e1Ds-kit344mbwx-qre1Ds-kit344mx-e1Ds-kit344ebfwx-e1 ... Show all
Save PDF