Page 3
C O N T E N T S Introduction Limited Warranty (USA Only) Warranty Registration | Features Safety Precautions Overview Installation Instructions Accessory Installation Aria Remote Device Management (RDM) Control Panel System Menu DMX Set Up DMX Traits Color Temperature Color Macros Dim Speeds Dim Modes...
Page 4
I N T R O D U C T I O N Unpacking: Thank you for purchasing the COB Cannon LP200X by ADJ Products, LLC. Every device has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping.
Page 5
L I M I T E D W A R R A N T Y ( U S A O N L Y ) A. ADJ Products, LLC hereby warrants, to the original purchaser, ADJ Products, LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse).
Page 6
W A R R A N T Y R E G I S T R A T I O N Please fill out the enclosed warranty card to validate your purchase. All returned service items, whether under warranty or not, must be freight pre-paid and accompanied by a return authorization (R.A.) number.
Page 7
S A F E T Y P R E C A U T I O N S PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED. THERE ARE NO USER SERVICEABLE PARTS INSIDE THIS UNIT. DO NOT ATTEMPT ANY REPAIRS YOURSELF, AS DOING SO WILL VOID YOUR MANUFACTURER’S WARRANTY.
Page 8
O V E R V I E W Display Screen Setup Button Button Mode Down Button Button Mounting Bracket Safety 2.4Ghz Cable Antenna Sub-Gig Attachment Antenna Point Fuse POWER OUT: AC 100V-240V 250VAC Max 9A Max.power linking:5 units Max.lien de puissance:5 unites Omega Power Power...
Page 9
I N S T A L L A T I O N I N S T R U C T I O N S DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO! Fixture MUST be installed following all local, national, and country commercial electrical and construction codes and regulations.
Page 10
I N S T A L L A T I O N I N S T R U C T I O N S CLAMP MOUNTING This fixture features a mounting hole for the attachment of mounting clamp on top of the mounting bracket.
Page 11
I N S T A L L A T I O N I N S T R U C T I O N S OMEGA BRACKET MOUNTING This fixture features mounting holes for the attachment of Omega clamps on the rear face near the control panel.
Page 12
I N S T A L L A T I O N I N S T R U C T I O N S The unit is fully operational in three different mounting positions: hanging upside-down from the ceiling or trussing, sideways on trussing, or set on a flat level surface. Be sure this fixture is kept at least 12m (40ft) away from any flammable materials (decorations, etc).
Page 13
I N S T A L L A T I O N I N S T R U C T I O N S POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS External sources of light beams from direct sunlight, lighting and moving head fixtures, and lasers, which are focused directly towards the exterior housing and/or penetrate the front lens opening of Elation lighting fixtures, can cause severe internal damage including burning of optics, dichroic color filters, glass and metal gobos, prisms, animation wheels, frost filters, iris, shutters, motors, belts,...
Page 14
A C C E S S O R Y I N S T A L L A T I O N LENSES This fixture can be fitted with either a 40° or 50° lens. To remove the lens, remove the lens retainer ring from its groove inside the lens frame, as shown below.
Page 15
A R I A To set up wireless control, follow the steps below: 1. Navigate to Personality > Aria in the system menu. Press SETUP to select this menu. 2. Use UP and DOWN to scroll to the “Aria Enable” option, then press SETUP to select. Use UP and DOWN to toggle this setting to ON, then press SETUP to confirm.
Page 16
R E M O T E D E V I C E M A N A G E M E N T ( R D M ) R E M O T E D E V I C E M A N A G E M E N T ( R D M ) NOTE: In order for RDM to work properly, RDM enabled equipment must be used throughout the entire system, including DMX data splitters and wireless systems.
Page 17
C O N T R O L P A N E L This unit features a display screen with a 4-button control pad, which can be used to easily adjust any device settings. Pressing the MODE button will cycle through the various Main Menu options. When the desired Main Menu option is displayed on the screen, press the SETUP button to enter the sub-menu, then use the UP and DOWN buttons to scroll through sub-menu options.
Page 18
S Y S T E M M E N U MENU OPTION OPTIONS/VALUES Address 001 - 512 8ch-A 8ch-B 10ch-A Ch Mode 10ch-B DMX Set 12ch 13ch 16ch 20ch Hold Blackout No DMX Manual Int Prog Primary/Secondary Primary / Secondry DMX or Aria Signal Aria In / DMX Out...
Page 19
S Y S T E M M E N U MENU OPTION OPTIONS/VALUES IR Function On / Off 000 - 255 Green 000 - 255 Button 0 Blue 000 - 255 Amber 000 - 255 Lime 000 - 255 000 - 255 Green 000 - 255 IR Button Colors...
Page 20
S Y S T E M M E N U MENU OPTION OPTIONS/VALUES 000 - 255 Green 000 - 255 Blue 000 - 255 Amber 000 - 255 Lime 000 - 255 Clr Macro 000 - 255 Clr Temp 000 - 255 Manual Clr Temp Pr Off, 2300k, 2400k...9900k...
Page 21
D M X S E T U P DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu- nication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN”...
Page 22
2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will reduce the risk of erratic behavior. DMX ADDRESSING.
Page 23
D M X T R A I T S 10-A 10-B FUNCTION VALUES 0 - 255 0 - 100% Red Fine 0 - 255 Fine adjustment, 16-bit Green 0 - 255 0 - 100% Green Fine 0 - 255 Fine adjustment, 16-bit Blue 0 - 255 0 - 100%...
Page 24
D M X T R A I T S 10-A 10-B FUNCTION VALUES Auto Programs (continued) 144 - 160 Auto Program 9 161 - 176 Auto Program 10 177 - 193 Auto Program 11 194 - 210 Auto Program 12 211 - 226 Auto Program 13 227 - 255 No Function Auto Programs Speed...
Page 25
C O L O R T E M P E R A T U R E COLOR GREEN BLUE AMBER LIME TEMP VALUES 0 - 15 No Function No Function No Function No Function No Function 2300K 16 - 31 2600K 32 - 47 2800K...
Page 26
C O L O R M A C R O S MACRO NO. DMX VALUES COLOR TEMP GREEN BLUE AMBER LIME 1 - 4 5 - 8 9 - 12 13 - 16 17 - 20 21 - 24 25 - 28 29 - 32 33 - 36 37 - 40...
Page 27
C O L O R M A C R O S MACRO NO. DMX VALUES COLOR TEMP GREEN BLUE AMBER LIME 169 - 172 173 - 176 177 - 180 181 - 184 185 - 188 189 - 192 193 - 196 197 - 200 2300K >...
Page 28
D I M S P E E D S DMX VALUES TIME 0.1s 0.2s 0.3s 0.4s 0.5s 0.6s 0.7s 0.8s 0.9s 1.0s 1.5s 2.0s 3.0s 4.0s 5.0s 6.0s 7.0s 8.0s 9.0s 10.0s...
Page 29
D I M M O D E S DIMMER DIMMER 100% 100% Time (ms) Time (ms) Rise Time Down Time 0 Sec 0 Sec Rise Time Down Time 0 sec Fade Time 1 sec Fade Time 0 sec Fade Time 1 sec Fade Time Dimming Curve Dimming Curve...
Page 30
R E M O T E C O N T R O L F U N C T I O N S This unit can be operated using the ADJ UC IR24 remote control. The unit can only be controlled when it has been set to Primary mode.
Page 31
I R D E FA U LT VA L U E S BUTTON GREEN BLUE AMBER LIME E D I T I N G I R B U T T O N VA L U E S These fixtures allow the user to create custom RGBAL values and assign them to the numbered keys (0-15) on the remote control.
Page 32
P R I M A R Y - S E C O N D A R Y S E T U P This function allows you to link units together to run in a Primary-Secondary set-up, in which one unit will act as the controlling unit and the others will react to the controlling unit’s built-in programs.
Page 33
Regular inspections are recommended to ensure proper function and extended life. There are no user serviceable parts inside this fixture. Please refer all other service issues to an authorized ADJ service technician. Should you need any spare parts, please order genuine parts from your local ADJ dealer.
Page 34
O R D E R I N G I N F O R M A T I O N SKU (US) SKU (EU) DESCRIPTION COB240 ADJ COB Cannon LP200X BAR001 COB Cannon Wash Barn Doors...
Page 35
D I M E N S I O N A L D R A W I N G S 13.9 in (353mm) 7.5 in (190mm) 10.3 in (262mm) 7.5 in (190mm)
Page 36
DMX • 64 built-in color macros • 4-button OLED digital DMX display on rear panel • Compatible with the ADJ UC IR remote con- trol (included) • LED pulse and strobe effect • Electronic Dimming: 0 - 100% •...
Page 37
F C C S T A T E M E N T Please note that changes or modifications to this product that are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Need help?
Do you have a question about the COB CANNON LP200X and is the answer not in the manual?
Questions and answers