REVV Generator 100R MK3 Owner's Manual page 11

R E V V | G E N E R A T O R 1 0 0 R M K 3
Now when you proceed to save your favorite settings
on each channel (using the "saving channels and
settings" method in this manual), you can also save
the FX Loop and either of the master volume controls
specifically.
Note: To toggle between the master controls and the
FX Loop on or off, you can either use the foot controller
or the GATE and REVERB buttons on the amp front
panel. If using the GATE and REVERB buttons, pressing
each button for 2 seconds will toggle these functions:
1. Reverb will toggle the FX loop on and off.
2. Gate will toggle between master 1 & 2
SAVING A DIGITAL CAB TO A BANK
When you want to save a cab to a bank along with your
favorite channels and settings to be recalled when you
press the bank button, the save must be performed in
the following order:
1. Select the bank you plan to make the save to.
2. Select the channel as well as drive or aggression
modes you plan to save to the bank.At this point the
bank LED on the foot controller will begin to flash.
3. Next you will need to select the cab you want saved
to the bank. If channel functions (Fat, Bright etc) are
selected first, the cab will not be saved.
4. Once you have selected your cab, you may proceed to
then select the functions you plan to save to the bank.
5. Once completed, press the bank button to store
these settings, the bank LED will stop flashing
confirming the save.
SAVING A DIGITAL CAB TO A CHANNEL
One cool feature of your amplifier is the ability to save
digital cabs to each channel, drive and aggression
settings! This will allow you to have many different
sounds with every channel, drive or aggression setting
change.
In order to save a cab to a channel, drive or aggression
setting:
20
1. Select the channel, drive or aggression setting
you want to save a digital speaker cab to.
2. Select the digital speaker cab bank you would
like saved with the 6 position rotary switch or
two notes remote software.
3. Press and hold the store button until the LED
flashes.
Now everytime you switch to that channel, drive or
aggression setting, the digital speaker cab you have
saved will be loaded by the Two Notes technology
inside!
DISABLE/ENABLE CAB SPEAKER
For those that have no desire to save digital speaker
48
cabinets, this feature can be disabled so that only
the same cab will be used no matter what channel or
setting you change.
With the main power in the OFF position.
1. Press and Hold the PRE-POST button then power
ON the amplifier.
2. When the Pre-Post LED begins to flash, release the
button.
3. If the PRE-POST LED flashes 5 times, the cab save
option is disabled. If the Pre-Post LED flashes 4
times, the cab save feature is enabled.
FACTORY RESET
If you would like to clear the amp's memory of all saved
program patches & restore all of the amps settings
to the factory default, which includes MIDI channel
(restored to CH1), OMNI Mode, FX Loop (Restored to
49
off at power-up) & a full memory clear, proceed with the
procedure below:
With power OFF, press & hold CH3 button & the CH3
BRIGHT button together & turn the power switch to the
ON position. The amplifier will flash the CH3 & CH3
BRIGHT LEDs to confirm that the factory defaults have
been restored.
Note: When resorting to the factory reset, just remember
that ALL settings in the amps memory will be erased.
FOOT
CONTROLLER
The Revv footswitch can be configured to either
operate as a normal footswitch (with some bonuses) or
a tool to quickly recall presets on the amplifier.
50
Control Mode: Select between all three channels,
drive, aggression modes, fx loop on/off, master
volumes, and a master mute function.
Preset Mode:
Select combinations of channel and
functions + master volume select & FX Loop on/off that
can be recalled with one button press.
Note: To switch between modes, press & hold the
footswitch button 1 for 2 seconds. The LEDs will all
illuminate then switch to the settings in the other mode. All
settings will be retained when switching between modes.
HOOK UP
The footswitch is connected to the rear of the amplifier
with a 5 PIN DIN Cable. The amplifier & footswitch
51
will work with any 5 PIN DIN cable should you be in a
pinch, but the Revv cable is always recommended for
best performance.
It is recommended that the footswitch be connected
to the amp with the power off, but should you plug it
in during amplifier use, it will power up & automatically
set itself to the amps current settings. Upon power-
up, all LEDs will turn on for a couple of seconds as it
initializes. Once complete, the foot pedal will set itself
to the amplifier's current configuration.
CONTROL MODE
The foot pedal will always power up in control mode.
This mode works similarly to most other foot pedals - it
simply controls the functions of the amp. Here is how
the buttons respond in control mode:
R E V V | G E N E R A T O R 1 0 0 R M K 3
BUTTON 1
This button has 3 functions, it switches to channel
one when the amp is not in channel one, switches
between clean and clean wide & switches between
foot pedal modes when held for 2 seconds (control
& preset).
BUTTON 2
This button will switch to channel two when the amp is
not in channel two. It will also toggle through Channel
2 drive modes when in the amp is in channel 2.
BUTTON 3
This button has two functions, it will switch to channel
52
3 when the amp is not in channel three, & cycle
through aggression levels when in channel 3.
BUTTON 4
This button toggles between the two master volume
controls.
BUTTON 5
This button toggles FX Loop In/Out.
BUTTON 6
This button turns mute on and off when pressed.
53
21