Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for REVV Generator 100P MK3
Summary of Contents for REVV Generator 100P MK3
- Page 1 Generator 100P MK3 Owner’s Manual...
- Page 2 I quickly built a team of people as passionate about guitar as I am, and Revv was born. To be honest, it grew bigger and faster than I had ever hoped...
-
Page 3: Table Of Contents
R E V V | G E N E R A T O R 1 0 0 P M K 3 TABLE OF CONTENTS Warranty TUBES AND BIAS P14/15 Safety Instructions & Warnings Set up & Power up Power Tubes Power Tube Sockets FRONT PANEL LAYOUT P7/10... -
Page 4: Warranty
This warranty will be honored with original proof of purchase to the original owner only. Warranty work must be authorized by Revv Amplification Inc. in advance. All freight and duty (If applicable) are to be prepaid to and from Revv Amplification Inc. of all products that require and have been approved for warranty work. Revv Amplification Inc. -
Page 5: P5 Safety Instructions & Warnings
R E V V | G E N E R A T O R 1 0 0 P M K 3 SAFETY & WARNINGS Please read, understand and follow all safety instructions in this manual, as well as those on the rear panel of the amplifier. - Page 6 Channel 1 (default) or your favorite saved • • FX Loop amp setting. • • Guitar & Shielded Revv Cabinet Lighting • Cable Headphones • • MIDI Revv Foot Controller •...
-
Page 7: Front Panel Layout
R E V V | G E N E R A T O R 1 0 0 P M K 3 FRONT PANEL INPUT CHANNEL TWO (CRUNCH) 1⁄4” Instrument cable input. Selected by: 1. pushing the designated front panel button, 2. footswitch button #2 or a footswitch preset mode setting, 3. -
Page 8: Channel Three (High Gain)
R E V V | G E N E R A T O R 1 0 0 P M K 3 The controls can be toggled via the footswitch button CHANNEL THREE (HIGH GAIN) #4 (or programmed bank) or a MIDI device. Selected by: 1. -
Page 9: Gate Switch
R E V V | G E N E R A T O R 1 0 0 P M K 3 the Pre-amp, then the real tube power amp won’t color GATE SWITCH the sound and the digital tube types can be used from the Two Notes tech in all their tone glory. -
Page 10: Virtual Cabinet Switch
R E V V | G E N E R A T O R 1 0 0 P M K 3 Note: The power delivered by the headphones output is STANDBY & POWER SWITCH high enough to remain efficient even when using high- impedance headphones. -
Page 11: Back Panel
R E V V | G E N E R A T O R 1 0 0 P M K 3 BACK PANEL MAIN POWER CONNECTION POWER TUBE FAULT FUSES When plugging the amplifier into the mains A/C wall The power tubes are fused in pairs. Should a power receptacle, always make sure the amplifier power &... -
Page 12: Xlr Output Connectors
R E V V | G E N E R A T O R 1 0 0 P M K 3 The ground lift switch will defeat the ground on the REVERB LEVEL CONTROL amp should you encounter ground noise from other equipment you have connected. -
Page 13: Cabinet Lighting
Some examples: Simply use the 4 pin Din cable provided with all Revv cabinets and connect the amplifier to the cab lighting • 2 - 8 ohm cabinets would be plugged into the the connector on the cabinet. -
Page 14: Power Tubes
EL34 tubes. tubes - but will accept the following tubes & gladly display their tonal characteristics for you in your Revv. Note: While we designed the amplifier to be easy to maintain, we advise that all tubes be set up by a... -
Page 15: Setting The Bias
R E V V | G E N E R A T O R 1 0 0 P M K 3 3. Now plug the amplifier into the main power 3. Next, place the red lead into the other red bias test receptacle, unplug any guitar cables from the point &... -
Page 16: Midi
SETUP 2. Press & hold “Reverb” push button. 3. With the “reverb” push button being held, turn on Versatile & optional MIDI control helps Revv amps the power switch. seamlessly integrate into any rig. The amplifier will store 4. Release the reverb push button once the reverb up to 128 programs for program change commands as LED begins to flash. -
Page 17: Midi Program Change
R E V V | G E N E R A T O R 1 0 0 P M K 3 MIDI channel 1 has been selected. Simply continue number. The Store LED will flash 3 times & turn off to press the CH 1 button to get to the channel you verifying that the command has been received &... - Page 18 R E V V | G E N E R A T O R 1 0 0 P M K 3 a CC number & then designate whether it be turned to The following commands control functions that are on or off. (Consult the external equipment instruction turned on &...
-
Page 19: Torpedo Remote/Load
4. Input the pin code to pair the Torpedo in your Revv amplifier amplifier but no speaker cab plugged into the other end and your mobile device. -
Page 20: Settings & Saving Cabinets
With the main power in the OFF position: While we know a lot of people like the color-changing Revv logo and cabinet lighting, some do not. The 1. Press and Hold the FAT button then option to turn this feature on and off has been added power ON the amplifier. -
Page 21: Saving A Digital Cab To A Bank
R E V V | G E N E R A T O R 1 0 0 P M K 3 Now when you proceed to save your favorite settings 1. Select the channel, drive or aggression setting on each channel (using the “saving channels and you want to save a digital speaker cab to. -
Page 22: Foot Controller
5 PIN DIN Cable. The amplifier & footswitch will work with any 5 PIN DIN cable should you be in a BUTTON 4 pinch, but the Revv cable is always recommended for This button toggles between the two master volume best performance. -
Page 23: Preset Mode
Note: When a preset is set on the footswitch, it will not Note: This will erase all your settings from the foot be lost if power is removed from the amp. The Revv controllers memory! footswitch has memory & will retain the settings. Each button is identical in Preset mode &...
Need help?
Do you have a question about the Generator 100P MK3 and is the answer not in the manual?
Questions and answers