Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for decon E-Walk
Summary of Contents for decon E-Walk
- Page 1 E-Walk User manual 2024-10 Rev1...
- Page 2 The undersigned, representing the following manufacturer Decon Wheel AB Org.No. 556618-9006 Södra Ekeryd 119, 314 91 Hyltebruk Sweden hereby declares that the product E-Walk with the basic UDI-DI 735001014MCGB3 and the following references MCG4055 MCG4755 is in conformity with the Medical Device Regulation (MDR) 2017/745 as a class 1 medical device based on Annex VIII.
- Page 3 Attaching the base unit to the wheelchair ..............15 Removing the base unit from wheelchair ..............16 Attachment of contoller ....................17 Running E-Walk.......................18 Transport and storage of E-Walk ................20 Battery and charger ...................... 22 Care ........................23 Cleaning ........................... 23 Corrosion ......................... 23 Repairs ..........................
- Page 4 Purpose and intended use E-Walk is an electric drive unit for manual wheelchairs that is intended for use both outdoors and indoors. E-Walk is exclusively intended for transport with the help of another person. E-Walk helps the accompanying person push and brake the wheelchair. With E-Walk you can handle longer excursions.
- Page 5 Serial number of the device Indication of the date of manufacture Name and adress of the manufacturer Catalogue number of the device Recycled as electronic waste. E-Walk and its accessories are subjected to the Euro- pean WEEE Directive. Page 5/26...
- Page 6 WARNING! To mount E-Walk to a wheelchair, a mounting set is required, which is ordered separately and is not included in deliveries of E-Walk. The mounting set must be assembled by a trained technician. WARNING! Be careful not to pinch your hand or fingers when using the handle to lower or raise the drive wheel.
- Page 7 Start with a low speed that feels safe for both you as the user and the patient. Then slowly increase the speed to the desired walking speed. WARNING! It is not permitted to drive E-Walk on slopes or ramps with a higher slope than 6 degrees (11.5%) with a user weight of 150 kg. WARNING! Avoid driving where the surface is soft or uneven (eg sand, mud, snow, ice or through deep puddles).
- Page 8 Storage and transport WARNING! Do not store E-Walk where it may get wet from rain or in places with high humidity. WARNING! Avoid storage in direct sunlight or high temperatures.
- Page 9 The warranty period for E-Walk is 2 (two) years from the date of purchase. If there is a material or manufacturing defect in your copy of E-Walk during this warranty period, the defective parts will be replaced or repaired free of charge. The warranty covers the base unit, controller and charger.
- Page 10 No condensation 1. Maximum speed is set via controller 2. With LiFePO4 battery. Driving style, surface and user weight affect the maximum driving distance. 3. Maximum gradient can be affected by the surface on which E-Walk is driven. Page 10/26...
- Page 11 The delivery of E-Walk includes the following: E-Walk base unit E-Walk controller User manual Charger incl. cables Mounting set INFO To mount E-Walk to a wheelchair, a mounting set is required, which is ordered separately and is not included in deliveries of E-Walk. Page 11/26...
- Page 12 E-Walk Product description User manual Overview E-Walk Battery Allen key S-Drive motor controller Charging socket Battery cover Lower handle Front pair of wheels Upper handle Drive wheel Throttle Front attachment Main switch Rear attachment Speed regulator Anchor point during transport...
- Page 13 Decon’s website, www.decon.se WARNING! To mount E-Walk on a wheelchair, a mounting set is required, which is ordered separate- ly and is not included in deliveries of E-Walk. The mounting set must be assembled by a trained technician. Page 13/26...
- Page 14 User manual Width adjustment E-Walk base unit can be adapted to different widths of wheelchairs. Allen key [O] for width adjustment is mounted on the base unit. Adjustment to different widths of wheelchairs is done by loosening the set screws [Y] using the Allen key [O] for width adjustment and then adjusting the side pieces [Z].
- Page 15 E-Walk Using E-Walk User manual Attaching the base unit to the wheelchair The base unit can be attached to the wheelchair in a few simple steps without the use of tools. This is done in the following steps. 1. Activate the wheelchair’s parking brakes 2.
- Page 16 E-Walk Using E-Walk User manual Removing the base unit from wheelchair The base unit can be detached from the wheelchair in a few simple steps without the use of tools. This is done in the following steps. 1. Activate the wheelchair parking brakes 2.
- Page 17 E-Walk Using E-Walk User manual Attachment of contoller General The controler can be mounted on the wheelchair’s handle or frame in just a few simple steps without the use of tools. The clamp [W] is opened and closed by screwing on the eccentric tensioner [AC] with its handle folded up.
- Page 18 E-Walk must under no circumstances be controlled by the patient sitting in the wheel- chair. In order to drive E-Walk, you must have first connected E-Walk’s base unit to the wheelchair according to the paragraph “Attaching the base unit to the wheelchair” and mounted the con- troller according to the paragraph “Attachment of controler”.
- Page 19 E-Walk may unintentionally start moving. WARNING! It is not permitted to drive E-Walk on slopes or ramps with a higher slope than 6 degrees (11.5%) with a user weight of 150 kg. WARNING! Avoid driving where the surface is soft or uneven (eg sand, mud, snow, ice or through deep puddles).
- Page 20 2. Remove the battery from E-Walk to prevent sudden power-on during storage or transport. 3. Load E-Walk into car. a. Lift E-Walk by the upper handle [R] and the front pair of wheels [H] when loading. b. Be careful not to damage the base unit when loading.
- Page 21 2. Store E-Walk in a place with normal indoor temperature and low humidity. 3. To wipe off dirt or stains before storage, use a tightly wrung-out towel. If E-Walk is not to be used for an extended period of time, check that E-Walk is working proper- ly every month.
- Page 22 Store the batteries in a cool and dry place (a place with a temperature between 10-25°C is optimal for storage). If you plan not to use E-Walk for an extended period of time (a month or more), charge the battery until six bars are displayed on the controller’s battery indicator [V] before storing it.
- Page 23 Care Cleaning If E-Walk becomes dirty due to normal use, clean E-Walk with a damp, tightly wrung out towel. If E-Walk is heavily soiled, use a towel and a neutral detergent. Make sure that no detergent remains on E-Walk after cleaning.
- Page 24 User manual Fuse replacement There are two replaceable fuses on E-Walk. One is a 25A main fuse which is located near the battery connector under the battery cover [G]. The second fuse for the controller is located on top of the S-drive motor control [F] and is rated at 2A.
- Page 25 Contact the service representative. Not in use Not in use The control unit is prevented from driving E-Walk. This may be due to the battery charger being plugged in. There is something wrong with the throttle signal. Make sure the throttle is off before starting E-Walk.
- Page 26 Decon Wheel AB Södra Ekeryd 119, 314 91 Hyltebruk Tel: +46 (0)345 40880 Fax: +46 (0)345 40895 E-mail: info@decon.se...
Need help?
Do you have a question about the E-Walk and is the answer not in the manual?
Questions and answers