Doss SoundBox Plus - Wireless Bluetooth Speaker Manual

Packing Content

• 1 x SoundBox Plus
• 1 x USB-C charging cable
• 1 x User manual

Specifictiaon

• Output power: 8W x 2
• lnput: DC 5V 2A
• Battery: 3.7V 3200mAh
• Unit dimension: 7.6 x 3.3 x 3.1 inches
• Play me: Up to 20 hours (50% volume without lights)
• Warranty: One-year limited
• Bluetooth distance: 66ft.

Illustration

Buttons and Controls

Indicators

Preparation

• Use the supplied charging cable to charge your portable speaker directly from your computer micro USB port or the cellphone adapter. (please confirm its output is 5V)
• Make sure that the speaker is fully charged before using it for the first me.
• The LED light will remain RED when charging and turn off once fully charged.
  Note:
  1. If the speaker beeps every few seconds, please recharge it for 3-4 hours.
  2. The speaker has a built-in battery-saver mode, which will automatically power off if not in use for 15 minutes. This function can be disabled via touch control. Please see the operations page. For further assistance, please contact: support@dossav.com

Operations

Multifunctional buttons

Pair your speaker with your smart device

1. Place your speaker and the smart device no more than 1 meter away.
2. Press the power button for a few seconds to turn the speaker on. Upon powering on, a tone will be heard, the blue LED starts flashing.
3. Turn on Bluetooth on your device and choose SoundBox Plus in the list.
4. If the pairing is successful, the LED will change to solid blue. If the pairing fails after 60 seconds, please press and hold the play/hand-free button for 5 seconds and try again.
5. Long press the play/hand-free button to disconnect the Bluetooth.
   Note: if your device cannot discover the SoundBox Plus, please long press the play/hand-free button and then try again.

Have problems connecting via Bluetooth?

1. Make sure that your device is within 1 meter from the speaker.
2. Clear the Bluetooth pairing list on your device.
3. Reset your device.
4. Try the pairing steps above again.
5. Problem still not resolved? Contact DOSS customer service at support@dossav.com for assistance.

Pair your device with the speaker via audio in cable

1. When using the audio input mode, control audio playback via the connected device.
2. When the auxiliary cable is plugged, the play mode will automatically switch to AUX IN mode.

Play music via SD card mode

1. Card capacity: 32G or below. If your micro SD card is larger than 32G, please format it to FAT32 or FAT.
2. Support files: MP3、WAV、WMA、APE、FLAC
3. Play order: music will play in the download/copy order

Answer or end a call using your speaker

1. Briefly tap the play/hand free button to pick up.
2. Speak with a clear voice right into the built-in microphone located on the front second of the speaker.
3. Tap the play/hand free button again to end the call.

Set true wireless stereo pairing

Start the first speaker
Turn on the speaker, press and hold the ADD button for 2 seconds.

Start the second speaker
Turn on the second speaker, press and hold the ADD button for 2 seconds.

Notes:

• Start the second speaker within 60 seconds, otherwise the stereo pairing setting of the first speaker will be canceled.
• If the pairing succeeds, the volume control ring of the master speaker is in solid blue, and the slave will flash blue every 5 seconds.
• The speaker will have stereo pairing automatically if they used to be paired.
• Press and hold the Play/hand free button for 3 seconds to cancel the stereo pairing mode.
• Under wireless stereo pairing, you can only change the modes( Bluetooth/ audio-in) on the master speaker.

Use your speaker with Echo Dot

You can connect the Dot with SoundBox Plus via a 3.5mm auxin cable or Bluetooth. Please follow the steps below to set up via Bluetooth:

1. Download the Alexa app and follow the standard setup procedure to get the dot connected to your home Wi-Fi network.
2. Set your speaker to Bluetooth mode. You can press the "Play/hand free" button for 5 seconds to keep it in pairing status.
3. Turn on the Alexa app, tap Menu, and then tap Settings.
4. Tap the Echo Dot in your list of Alexa devices and tap Bluetooth.
5. The SoundBox Plus should appear in the list of Bluetooth devices. If it does not, then press the "Play/hand free" button for 5 seconds and try again. Once listed, tap on the speaker to complete the pairing process.
6. To remove the device, return to Bluetooth > tap the name of the speaker > tap "Forget device".

Trouble shooting

Safety Instructions

• Do NOT drop, hit, or shake the device.
• Do NOT disassemble, repair, or modify the speaker.
• Do NOT use cleaning stuff that contains benzene, solvents, or alcohol.
• Do NOT expose the speaker to excessive heat or direct sunlight for prolonged periods.
• Do NOT store the device in a place with high humidity or dust.
• Do NOT place heavy objects on the speaker.
• Do NOT use the speaker near a microwave oven or wireless LAN products.

Notice
This product complies with the radio interference requirements of the European Community.

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

Documents / Resources

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Doss SoundBox Plus - Wireless Bluetooth Speaker Manual