Table of Contents
Advertisement
Quick Links
CROSSWAVE
MULTI-SURFACE HARD FLOOR CLEANER
3930, 3933, 3934 SERIES
1. Get Ready
Assemble and charge machine (pg 5). If dry cleaning,
strainer could be removed for increased tank capacity (pg 6).
If wet cleaning, fill the clean water tank (pg 7).
2. Choose Your Cleaning Mode
Press (C) to power on. Choose mode with (B). View selection
on (D). When using both modes in one cleaning session,
start with Power Vac Mode for dry cleaning and then switch
to Power Mop Mode.
Power Vac Mode
Great for dry debris on
hard floors and area rugs.
3. Start Cleaning
Recline machine with your foot to start brush roll.
For extra fluid and suction, use Turbo Mode (A).
For dry and wet cleaning against walls and
baseboards, use ZeroGap™ Edge Cleaning (E),
located on the right side of the foot.
CLEANING TIPS
• For best results, use on hard floors and large/heavy area rugs.
Follow manufacturer's instructions for small/lightweight rugs.
• If planning to store for over 6 months, ensure the battery is
fully charged before storage.
Scan the QR code for product videos, tips, and support.
OMNIFORCE
®
QUICK START GUIDE
Power Mop Mode
Efficiently clean wet and
dry messes together.
EDGE
™
E
A
B
C
D
Advertisement
Table of Contents
Related Manuals for Bissell CROSSWAVE OMNIFORCE EDGE 3930 Series
Summary of Contents for Bissell CROSSWAVE OMNIFORCE EDGE 3930 Series
- Page 1 CROSSWAVE OMNIFORCE EDGE ™ ® MULTI-SURFACE HARD FLOOR CLEANER 3930, 3933, 3934 SERIES QUICK START GUIDE 1. Get Ready Assemble and charge machine (pg 5). If dry cleaning, strainer could be removed for increased tank capacity (pg 6). If wet cleaning, fill the clean water tank (pg 7). 2.
-
Page 2: Important Safety Instructions
See the “Power Mop Mode & • Follow all charging instructions and do not charge the appliance Compatible BISSELL Formulas” section of this guide. outside of the temperature range specified in the instructions. • Do not allow to be used as a toy. Close attention is necessary when Charging improperly or at temperatures outside of the specified used by or near children. -
Page 3: Table Of Contents
Supplier’s Declaration of Conformity 47 CRF Section 2.1077 Compliance Information Charger for BISSELL model CONTACT: BISSELL Homecare Inc., 2345 Walker Ave. NW, Grand Rapids, MI 49544. Visit support.BISSELL.com or call 1-800-237-7691. This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Page 4: Product Overview
1. Dirty Tank Full 2. Error Indicator 3. Charging 4. Low Battery 5. Battery % Remaining 6. Clog Detected 7. Suction Level 8. Fluid Level 9. Brush Roll Stuck 10. Clean-Out Cycle Indicator 11. Clean Tank Empty 4 BISSELL.com... -
Page 5: Assembly & Charging The Battery
Let charge for 4 hours or until battery reaches 100% charge. WARNING To reduce the risk of fire and electric shock due to internal component damage, use only BISSELL cleaning formula intended for use with this machine. BISSELL.com 5... -
Page 6: Power Vac Mode
4. Pull the strainer tab up and 5. Replace strainer and place 6. Insert bottom of tank first. remove debris. Empty tank filter into lid. Return lid to dirty Tilt tank towards machine until into trash can. tank. it clicks into place. 6 BISSELL.com... -
Page 7: Power Mop Mode
Power Mop Mode For optimal performance, use genuine BISSELL formulas in your machine*. Other formulas or household cleaners may cause defects or damage to the machine. When using both modes in one cleaning session, start with Power Vac Mode for dry cleaning and then switch to Power Mop Mode since parts need to dry for 24 hours after use. - Page 8 Power Mop Mode (continued) Sanitizing Hard Floors BISSELL Hard Floor Sanitize formula is for use on hard, sealed floors only. Do not use on carpet or area rugs. Read formula container label fully prior to use. 1. Follow cleaning instructions on page 7 to 2.
-
Page 9: Using The Clean-Out Cycle
Note: If brush roll is still dirty, it can be hand washed with mild detergent and place in brush roll holder on charging tray to dry. For best results, replace brush roll every 3 months. BISSELL.com 9... -
Page 10: After-Cleaning Care
Tilt tank towards locked in place. machine. Press down until machine until it clicks into window clicks into place. place. Note: Any other maintenance or servicing not included in this manual should be performed by an authorized service representative. 10 BISSELL.com... -
Page 11: Troubleshooting
Remove any accumulated hair from brush roll. Fan error Contact BISSELL Consumer Care. Battery communication error Contact BISSELL Consumer Care. The battery is to be disposed of safely. See support.BISSELL.com for battery removal instructions. BISSELL.com 11... - Page 12 BISSELL proudly supports BISSELL Pet Foundation® and its mission to help save homeless pets. When you buy a BISSELL® product, you help save pets, too. We’re proud to design products that help make pet messes, odors and pet homelessness disappear.
Need help?
Do you have a question about the CROSSWAVE OMNIFORCE EDGE 3930 Series and is the answer not in the manual?
Questions and answers