ENGLISH Contents 1.0 Safety Precautions 2.0 Product Description 5.0 Description of Controls and Torch Connections 7.0 Setting the Machine for Welding 10-20 11.0 EC Declaration of Conformity 29-30...
When using an open arc process, it is necessary to use correct eye, head, and body protection. 2.0 Product Description FLYING METAL can injure eyes. BUILDUP OF GAS can injure or kill. HOT PARTS can cause severe burns. NOISE can damage hearing. www.parweld.com...
11. Multifunction Control Knob 12. Amperage / Wire Speed Adjustment 13. Voltage / Downslope / Arc Force Adjustment 14. Inductance / Post Gas Control 15. Digital Display TIG Torch Gas Connector 17. TIG Torch Trigger Connector Plasma torch connector www.parweld.com...
Page 8
ENGLISH MIG SYN Multifunction Control Knob. ntrol Knob. MIG MAN Plasma Cutting setup www.parweld.com...
Page 9
Note: There is a friction brake on the reel hub assembly to prevent the wire spool over running when welding stops; ensure this is slackened to the minimum setting. It can be adjusted by means of the nut visible when the plastic hand nut is removed. www.parweld.com...
ENGLISH MIG Torch Installation (continued) 7.2 MIG SYN Burn back Soft start 7.0 Setting the Machine for Welding 7.1 MIG Torch Selection www.parweld.com...
Page 11
ENGLISH Operating screen (MIG SYN) 7.4 Remote Control MIG Torch MIG SYN MIG MAN 7.3 MIG MAN Torch with OLED Display Torch with 4 Button Control www.parweld.com...
Page 13
ENGLISH 7.7.2 TIG Torch Installation 7.7.3 TIG Welding Set Up www.parweld.com...
Page 14
ENGLISH -2T -4T 2T mode www.parweld.com...
Page 15
Note:- shorting or dipping the electrode into the weld pool for more than 1 second will cause the machine to reduce the welding power to zero in order to protect the tungsten and minimise contamination. TIG welding guide ranges Tungsten electrode types www.parweld.com...
Page 16
Note:- shorting or dipping the electrode into the weld pool for more than 1 second will cause the machine to reduce the welding power to zero in order to protect the tungsten and minimise contamination. Note this function only operates in 4T switch mode www.parweld.com...
Page 17
ENGLISH 7.7.7 TIG welding (With Pulse) Note this function only operates in 4T switch mode. Note this function only operates in 4T switch mode. www.parweld.com...
Page 18
CAUTION: Before switching on the machine ensure all spares do so can result in the destruction of the torch head. Connect the air line to the rear of the machine and Switch on the machine. The air supply should be capable of supplying air delivery. www.parweld.com...
Page 19
To Air flow Cutting goes off starts Press Cutting Release trigger stops trigger Cutting stops air flows for 15 seconds www.parweld.com...
Page 20
ENGLISH 7.9 Saving to Memory 7.10 Process Switch www.parweld.com...
Page 21
ENGLISH Problem Cause/Corrective Action If error message is displayed allow machine to cool with Reduce welding current to prevent over current condition. If error remains contact your local service centre. www.parweld.com...
Page 22
ENGLISH Problem Cause/Corrective Action Problem Cause/Corrective Action www.parweld.com...
Page 23
ENGLISH Description Possible cause Remedy Description Possible cause Remedy www.parweld.com...
Page 24
ENGLISH Description Possible cause Remedy Description Possible cause Remedy www.parweld.com...
Page 25
Possible cause Remedy Air pressure is set to low Adjust air pressure illuminates when trigger power source pressed Outer nozzle or other re-assemble front consumable not installed end spares to trigger pressed correctly ensure outer nozzle is seated fully. source www.parweld.com...
Need help?
Do you have a question about the XTM 221Di and is the answer not in the manual?
Questions and answers