Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Parweld XTM 201Di
Summary of Contents for Parweld XTM 201Di
- Page 1 XTM 201Di OPERATOR MANUAL ISSUE 1...
- Page 2 European directives and the product specific standards where they apply. Further Information Parweld is the UK’s leading supplier of MIG, TIG and Plasma torches and consumables. For more information about Parweld’s complete range visit: www.parweld.com...
-
Page 3: Table Of Contents
8.2 MMA Welding Problems 8.3 TIG Welding Problems 9.0 Control Torch Schematic 10.0 Accessories 10.1 Feed Rolls 10.2 Torch Spares 10.3 Gas Equipment 11.0 EC Declaration of Conformity 11.1 RoHS Compliance Declaration 11.2 WEEE Statement 11.3 Statement of Warranty www.parweld.com... -
Page 4: Safety Precautions
Use only well-maintained equipment. Repair or replace damaged explosion, overheating, or fire. Check and be sure the area is safe parts at once. Maintain unit according to manual. before doing any welding. Wear a safety harness if working above floor level. www.parweld.com... -
Page 5: Product Description
HOT PARTS can cause severe burns. Do not touch hot parts with bare handed. The XTM 201Di is a multi-mode welding machine using inverter Allow cooling period before working on gun or torch. technology. A micro controller allows the machine to be quickly and easily configured for MIG, TIG and MMA welding operations. -
Page 6: Technical Specifications
Specifications Read entire installation section before starting installation. SAFETY PRECAUTIONS The XTM 201Di, is a compact type machine with integrated wire feed • ELECTRIC SHOCK can kill. unit for use with single phase 110/230V supply with smart • Only qualified personnel should perform this installation. -
Page 7: Description Of Controls
6. Wire Spool Holder 7. Wire Feed Unit 8. Polarity Changeover 9. Burn Back Control 10. Multifunction Control Knob 11. Amperage / Wire Speed Adjustment 12. Voltage / Downslope / Arc Force Adjustment 13. Inductance / Post Gas Control 14. Digital Display www.parweld.com... -
Page 8: Operation
Short press at end of menu returns to start menu MIG MAN Manual MIG Welding Setup 6.2 Language of Operation TIG Synergic TIG Welding Setup MMA Synergic MMA Welding Setup Short Press (1 sec) to return to start menu www.parweld.com... -
Page 9: Mig Welding Preparing The Machine
MIG Torch Installation 2. Release the pressure on the idle roll by swinging the adjustable Your Parweld MIG/MAG Welding Torch has been supplied ready to pressure arm down towards the front of the machine. Lift the idle weld. It has been supplied with the standard consumables denoted roll assembly and allow it to sit in an upright position. -
Page 10: Setting The Machine For Mig Welding
Soft start The machine has a pre-set soft start system. 7.0 Setting the Machine for MIG Welding 7.1 MIG SYN Synergic MIG Welding Allows Simple and Rapid Setup. Follow the screen prompts to complete the machine setup. Example setting. www.parweld.com... -
Page 11: Mig Man - Manual Mig Welding
Follow the screen prompts to complete the machine setup. Example setting. Adjust Wire Speed Value Adjust Voltage Value Adjust Inductance (short circuit current) In manual mode you can adjust the parameters using the controls indicated. Wire Speed Voltage Inductance www.parweld.com... -
Page 12: Tig Welding
7.5 TIG Welding Follow the screen prompts to complete the machine setup. Example setting. Adjust Amperage Value Adjust Arcforce Value www.parweld.com... -
Page 13: Tig Welding Operation Guide
• If error message is displayed allow machine to cool with power off for 10 minutes. • If error remains switch off and on again. • Reduce welding current to prevent over current condition. • If error remains contact your local service centre. www.parweld.com... -
Page 14: Mig Welding Problems
Dirty welding wire. Use clean, dry welding wire. Eliminate pickup of oil or lubricant on welding wire from feeder or liner. Wire feed unit operates but no Gas cylinder empty gas flow . Gas regulator closed Faulty solenoid Restriction in torch cables www.parweld.com... -
Page 15: Mma Welding Problems
(d) Travel speed of current electrode is too high (c) Adjust (e) Scale or dirt on joint angle so the surface welding arc is directed more into the base metal (d) Reduce travel speed of electrode (e) Clean surface before welding. www.parweld.com... -
Page 16: Tig Welding Problems
(g) The electrode is too (e) Turn on small for the welding (f) Turn on current (g) Increase electrode diameter or reduce the welding current Poor weld finish Inadequate shielding Increase gas flow or check gas line for gas flow problems www.parweld.com... -
Page 17: Control Torch Schematic
Steel Liner .023"-.035"/0.6mm-0.9mm x 5m B1524 Gun Plug ‘O’ Ring B2524-30* Steel Liner .040"-.045"/1.0mm-1.2mm x 3m B1525 Liner Nut B2524-40* Steel Liner .040"-.045"/1.0mm-1.2mm x 4m PROMC4 4 Button MIG Control Module B2524-50* Steel Liner .040"-.045"/1.0mm-1.2mm x 5m B1536-30 Teflon Liner .023"-.035"/0.6mm-0.9mm x 3m www.parweld.com... -
Page 18: Accessories
Stock Code Description 706101 Flow Meter Mixed Gas 25 lpm (MIG) 706100 Flow Meter 0-12 lpm (TIG) Gas flow Tester • Designed to check gas flow at the front of MIG Torches. Stock Code Description 806001 Gas flow Tester www.parweld.com... -
Page 19: Ec Declaration Of Conformity
11.0 EC Declaration of Conformity Hereby we declare that the machines as stated below Type: XTM 201Di Conform to the EC Directives: Low Voltage Directive 2006/95/EC EMC Directive 2004/108/EC Harmonised European standard: EN/IEC 60974-1 This is to certify that the tested sample is in conformity with all provisions of the above detailed EU directives and product standards. -
Page 20: Weee Statement
The warranty is effective from the date that the authorized Distributor delivers the products to the purchaser. Not withstanding the foregoing, in no event shall the warranty period extend more than the time stated plus one month from the date Parweld delivered the product to the authorized distributor. - Page 21 www.parweld.com...
- Page 22 www.parweld.com...
- Page 23 www.parweld.com...
- Page 24 Parweld Limited Bewdley Business Park Long Bank Bewdley Worcestershire England DY12 2TZ Tel. +44 1299 266800 Fax. +44 1299 266900 www.parweld.com info@parweld.co.uk www.parweld.com...
Need help?
Do you have a question about the XTM 201Di and is the answer not in the manual?
Questions and answers