Troubleshooting - CCS Lighting Solution PD3-10024-8-SI Instruction Manual

10
Errors
If an internal error occurs in the Control Unit, it is displayed on the digital window.
Refer to the following table and clear the error before using the Control Unit again.
Digital Window Error
Overcurrent Error
The current consumption of the Light
Unit exceeded 107% of the rating.
Fan Stop Error
The fan has stopped.
HLV ID Error
A Spotlight outside the ID range was
connected to an HLV LIGHT connector.
If the channel that is connected to a Spotlight that is
outside the ID range is selected, an error will be displayed.
OR
If no Light Unit has ever been
connected to the same channel in the 24V
LIGHT connectors, EId will be displayed.
If a Light Unit is connected to the
(Example display)
same channel in the 24V LIGHT connectors,
" ." is displayed. (" " is the set value.)
Period
Light Units that are connected to 24V
LIGHT connectors can be set normally.
Error Output
When detecting the error during external control, command will be received as
acknowledgement for checking status (over current confirmation) command "C".
(This applies only to overcurrent errors and fan stop errors.)
For details, refer to 8. Control with External Signals.
12

Troubleshooting

If you have any problems during product usage, please look up the cause in this chart. If the situation does not improve, or an unexpected situation
occurs, please contact CCS Inc.
Symptom Symptom Items to check for fixing the problem Items to check for fixing the problem
Lights not Are all power sources turned ON?
illuminating.
Is the LED light cable inserted firmly into the output connector?
Is the AC cord inserted firmly into the AC inlet and a wall
socket?
Does the digital window show an error?
Check the error display.
Is an appropriate Light Unit connected to the output
connector? Check the Light Unit.
Is the output connector the correct one for the connected
Light Unit? Connect 24V DC Light Units to the 24V LIGHT
connectors and Spotlights to HLV LIGHT connectors.
Is the lighting mode set correctly?
Set the lighting mode to F00 for Continuous Mode or
ON/OFF Mode.
Does the logic of the trigger signal match the trigger
signal setting switch?
Is the external trigger input OFF (in ON/OFF Mode or Strobe
Mode)? Check the setting method and sequence diagram.
Light intensity Is the manual/external switch set correctly?
control is not Set it to MANU to operate manually and to EXT for
possible.
external control.
Is an appropriate Light Unit connected to the output
connector? Check the Light Unit.
Is the output connector the correct one for the connected
Light Unit? Connect 24V DC Light Units to the 24V LIGHT
connectors and Spotlights to HLV LIGHT connectors.
Have the wrong channels been selected?
Check the channels whose lights are to be controlled.
Is the setting switch locked?
Press and hold the setting switch for more than two
seconds to release the lock.
Status
Clearing the error Recovery method
Check the rating of the
Press and hold the
Output is
LED Light Unit. Connect
setting switch or
stopped.
an LED Light Unit that is
cycle the power.
within the rating.
Doing so may cause
Press and hold the
Output is
product failure.
setting switch or
stopped.
Consult a CCS
cycle the power.
representative.
Check the Spotlight.
Connect a Spotlight
Operation recovers
Normal
that is supported by automatically.
the Control Unit.
Reference
page
11
Optional Accessories (Sold Separately)
External Control Cable
1
2
3
e-CON 3-pole connector
External Control Junction Cable
External Control Junction Cable Model: EXCB2-E3-E3-0.2
1
2
3
Junction Connector Model: ECNR-E3CN4
External Trigger Input Cable
2
1
9 10
10-pole MIL connector
Symptom Items to check for fixing the problem
3
External control is Is the external control cable inserted firmly into the
not possible. external control connector and an external device?
3
Was the command sent correctly?
Set the data correctly.
3
Are the ID switches set correctly?
Do the ID designation and the ID switches agree?
9
If the Control Unit has more than one Light Unit
connected on the same signal line, is the external control
4
junction cable connected securely to the external control
connector on the Control Unit?
4
Unable to turn the Is the external trigger input cable inserted firmly into the
Light Unit ON and external trigger input connector and an external device?
OFF or use strobe
control.
Are the external trigger input cable and external devices
5, 6
wired correctly?
Check the connector configuration and correct the wiring.
Is the lighting mode set correctly?
8
Set the value to F00 for ON/OFF Mode.
Set the value to F01 to F10 for Strobe Mode.
8
Is the signal setting correct?
Check the setting method and sequence diagram.
5, 6
Please use designated power sources with stable voltage.
Malfunctioning.
Sharing power sources with inverters, motors, etc., may
cause malfunction.
4
Do not bundle product cables with high-voltage lines or power
lines. Doing so may cause the product to malfunction. Keep
the product cables as far away from such lines as possible.
4
There is a possibility of product failure. Please stop usage
Fuming, extreme
temperature, smell, immediately and turn OFF the power switch.
noise, or other
Please do not attempt to use or repair the product, since
5, 6
abnormality. it is dangerous, but contact CCS Inc.
5
9 9
Model: EXCB2-E3-3
3000 + 150
0
Connector: 37103-3122-000FL (manufactured by Sumitomo 3M Limited)
200 + 10
0
e-CON 3-pole connector
Connector: 37103-3122-000FL (manufactured by Sumitomo 3M Limited)
13.8 30
Connector: 5-1473574-3 (manufactured by Tyco Electronics Japan G.K.)
Model: EXCB2-M10-3
3000 + 150
0
Connector: XG4M-1030-T (manufactured by OMRON)
Cut off on one end
Cut off on one end
Reference
page
3
6, 7
6, 7
7
3
8
5, 6
8
-
-
-