Related Manuals for TP-Link TL-SH1206
Summary of Contents for TP-Link TL-SH1206
- Page 1 Machine Translated by Google Enterprise Networking Solution Installation Manual 10G uplink Ethernet switch TL-SH1206...
- Page 2 Machine Translated by Google statement Copyright © 2020 Pulian Technology Co., Ltd. All rights reserved. Without the express written permission of Pulian Technology Co., Ltd., no unit or individual may copy, copy, copy or translate part or all of the contents of this manual without authorization, and no part or all of the contents of this manual may be reproduced in any way (electronically, photocopied, recorded, etc.) for profit.
- Page 3 Introduces the installation and startup process of this model of switch If the problem still cannot be solved through the guidance of relevant documents, please contact the TP-LINK technical support service center directly and we will provide you with technical support services.
- Page 4 Agreement In the following parts of this manual, unless otherwise specified, the switch mentioned refers to the TL-SH1206 10G uplink Ethernet switch. Replacement machine, hereafter referred to as TL-SH1206. This manual uses the following eye-catching symbols to indicate the points that should be paid attention to during operation. The meanings of these symbols are as follows: Down: This icon indicates a warning that requires attention.
-
Page 5: Table Of Contents
Machine Translated by Google Table of contents Chapter 1 Table of Contents Chapter 1 Product Introduction—————————————— 01 1.1 Product Introduction............01 1.2 Product Appearance ............01 Chapter 2 Product Installation—————————————— 04 2.1 List of items............04 2.2 Installation precautions..........04 2.3 Preparation of installation tools........ -
Page 6: Chapter 1 Product Introduction
Chapter 1 Product Introduction 1.1 Product introduction TL-SH1206 is a 10G uplink Ethernet switch independently developed by Pulian Technology Co., Ltd. It provides four 2.5Gbps RJ45 ports and two 10Gbps SFP+ ports, and supports two working modes: standard switching and VLAN isolation. -
Page 7: Rear Panel
Machine Translated by Google 10 Gigabit Uplink Ethernet Switch Installation Manual Indicator light working status working instructions Steady green corresponds to a port connection rate of 10Gbps Yellow solid light corresponds to a port connection rate of 1Gbps Link/Act (5-6) Flashing: There is data transmission on the corresponding port. - Page 8 Machine Translated by Google 10 Gigabit Uplink Ethernet Switch Installation Manual Note: ÿ Please use the original power cord and connect it to an AC power supply of 100-240Vÿ50/60Hz. ÿ Please install the power socket in an easily accessible location near the device for easy operation. 03Product introduction...
-
Page 9: Chapter 2 Product Installation
Installation Manual 10 Gigabit Uplink Ethernet Switch TL-SH1206 Two L-shaped brackets for fixing to the rack A warranty card and a toxic and hazardous substance and other accessories content statement Warranty Card Note: If you find any parts are missing or damaged, please contact your local dealer in time. - Page 10 Machine Translated by Google 10 Gigabit Uplink Ethernet Switch Installation Manual ÿ Installation environment precautions temperature humidity 40ÿ 0ÿ To ensure long-term stable operation of the switch and extend its service life, please maintain a certain temperature and humidity in the environment. Too high or too low ambient humidity can easily cause leakage, deformation and even corrosion of metal parts in insulating materials.
-
Page 11: Preparation Of Installation Tools
Machine Translated by Google 10 Gigabit Uplink Ethernet Switch Installation Manual ÿ Switches should be kept away from high-frequency, high-power, and high-current equipment, such as wireless transmitters; ÿ Take electromagnetic shielding measures if necessary. Lightning protection requirements When a lightning strike occurs, a strong current will be generated in an instant, and the air on the discharge path will be instantly heated to 20,000 degrees Celsius. The instantaneous high current is enough to cause fatal damage to electronic equipment. - Page 12 Machine Translated by Google 10 Gigabit Uplink Ethernet Switch Installation Manual Note: Leave a 5-10cm gap around the switch case to ensure heat dissipation and air circulation. Avoid placing other heavy objects on the surface of the switch. 1. Place the switch with the bottom facing up on a sufficiently large and stable table; 2. Peel off the rubber protective paper of the four foot pads one by one, and stick them in the circular grooves located at the four corners of the bottom of the case;...
- Page 13 Excellent grounding method. ÿ If you install TP-LINK enterprise-grade steel shell products in the computer room, and there is a dedicated grounding bar in the computer room, you should first consider using Use a ground wire to connect the device to the ground bar, as shown in Figure 2-4.
-
Page 14: Chapter 3 Hardware Connection
Machine Translated by Google 10 Gigabit Uplink Ethernet Switch Installation Manual Chapter 3 Hardware Connection 3.1 Connect to RJ45 port This model switch provides four 2.5Gbps RJ45 ports and two 10Gbps SFP+ ports. The connection process to the peer Ethernet port is as follows: 1. -
Page 15: Connecting The Power Supply
Machine Translated by Google 10 Gigabit Uplink Ethernet Switch Installation Manual SFP+ port fiber module Figure 3-2 SFP+ port connection diagram Note: ÿ Excessive bending of the optical fiber is not allowed, and the radius of curvature should not be less than 10cm;... -
Page 16: Installation Inspection
Machine Translated by Google 10 Gigabit Uplink Ethernet Switch Installation Manual 3.5 Post-installation inspection Please check the following after installation: ÿ Check whether there is enough cooling space around the switch and whether the air circulation is smooth; ÿ Check whether the power supply from the power outlet meets the switch specifications; ÿ... -
Page 17: Appendix A Technical Parameters And Specifications
Machine Translated by Google 10 Gigabit Uplink Ethernet Switch Installation Manual Appendix A Technical Parameters and Specifications Parameter content Parameter item IEEE 802.3 Ethernet Media Access Control (MAC) Protocol IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3ab 1000BASE-T Gigabit Ethernet IEEE 802.3z 1000BASE-X Gigabit Ethernet IEEE 802.3bz 2.5G BASE-T Gigabit Ethernet IEEE Supported standards and protocols 802.3ae 10GBASE-SR/LR 10G Ethernet IEEE 802.3x flow control... -
Page 18: Appendix B Supplementary Instructions For Connecting The Sfp+ Port
The 10G SFP+ port of the TP-LINK switch is compatible with single-mode and multi-mode optical modules. It is recommended to use TP-LINK's 10G optical module. modules, such as TL-SM512LM-300m and TL-SM512LS-10KM, are small and can be installed directly inside the switch. - Page 19 Machine Translated by Google...
- Page 20 Company address: 1st floor, 3-5th floor of the south section of Building 24, Science and Technology Park Industrial Factory, Shennan Road, Nanshan District, Shenzhen City, 1st-4th floor of the northern section of Building 28 Company website: http://www.tp-link.com.cn Technical support hotline: 400-8863-400 E-mail: smb@tp-link.com.cn...
Need help?
Do you have a question about the TL-SH1206 and is the answer not in the manual?
Questions and answers