Renesas PTX105R/RA2E1 Quick Start Manual

Renesas PTX105R/RA2E1 Quick Start Manual

Quick connect (qc) demo

Advertisement

Quick Links

PTX105R/RA2E1 Quick Connect (QC) Demo
This document describes how to use the PTX IoT Reader demo application with the Renesas
running it on the
Renesas EK-RA2E1
Contents
1.
Introduction ................................................................................................................................................... 2
2.
Requirements ................................................................................................................................................ 2
2.1
Hardware .............................................................................................................................................. 2
2.2
Software ............................................................................................................................................... 3
3.
PTX105R Quick-Connect (QC) Board.......................................................................................................... 3
4.
EK-RA2E1 Evaluation Kit ............................................................................................................................. 3
5.
Hardware Setup ............................................................................................................................................ 4
6.
IoT Reader Demo Application ...................................................................................................................... 4
7.
Running the Example Application............................................................................................................... 6
8.
Using IoT Reader Library in a Custom Project .......................................................................................... 9
8.1
Integrating the Library in a Custom Project......................................................................................... 10
8.2
Supported Architectures ..................................................................................................................... 10
8.3
Platform-Specific Implementation ....................................................................................................... 10
9.
PTX105R QC Schematic ............................................................................................................................. 11
10. Revision History ......................................................................................................................................... 11
Figures
Figure 1. PTX105RQC and EK-RA2E1 Boards ...................................................................................................... 2
Figure 2. PTX105R Quick-Connect (QC) Board ..................................................................................................... 3
Figure 3. Connecting the PTX105RQC and EK-RA2E1 Boards ............................................................................. 4
Figure 4. Application Flow Diagram ........................................................................................................................ 5
Figure 5. Application Output Example on the SEGGER RTT Viewer ..................................................................... 5
Figure 6. Import Projects Windows ......................................................................................................................... 6
Figure 7. Debug Configuration Windows ................................................................................................................ 7
Figure 8. Application Startup Window..................................................................................................................... 8
Figure 9. J-Link RTT Viewer Window ..................................................................................................................... 8
Figure 10. RTT Viewer Terminals Window ............................................................................................................. 9
Figure 11. PTX105R-DB-RB QFN56-IOT QC Schematic ..................................................................................... 11
R35UH0019EU0100 Rev.1.00
Sep 25, 2024
evaluation board with a
Quick Start Guide
PTX105RQC
PMOD™ board.
© 2024 Renesas Electronics
e² studio
and
Page 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PTX105R/RA2E1 and is the answer not in the manual?

Questions and answers

Summary of Contents for Renesas PTX105R/RA2E1

  • Page 1: Table Of Contents

    Quick Start Guide PTX105R/RA2E1 Quick Connect (QC) Demo This document describes how to use the PTX IoT Reader demo application with the Renesas e² studio running it on the Renesas EK-RA2E1 evaluation board with a PTX105RQC PMOD™ board. Contents Introduction ..............................2 Requirements ..............................
  • Page 2: Introduction

    1. Introduction This document describes the usage of the PTX IoT Reader demo application using e² studio and running it on the Renesas EK-RA2E1 evaluation board with a PTX105RQC board attached to the PMOD connector. For more information, see the PTX105R NFC Reader Evaluation Kit and PMOD Demonstration video.
  • Page 3: Software

    The module contains a PTX105R chip with a 20 × 20 mm loop antenna. The board can be connected directly to the Renesas EK-RA2E1 via the PMOD connector. The SPI and IRQ pins are used for the communication and the required operating current is drawn from the 3V3 pin.
  • Page 4: Hardware Setup

    PTX105R/RA2E1 Quick Connect (QC) Demo Quick Start Guide 5. Hardware Setup 1. Connect the PTX105R Quick-Connect board to the EK-RA2E1 PMOD1 connector (J26). Figure 3. Connecting the PTX105RQC and EK-RA2E1 Boards 2. Plug in the micro-USB communication cable to the debugger USB connector (J10) on EK-RA2E1. When the cable is connected, the EK-RA2E1 board supplies the PTX105R Quick-Connect board with 3.3V.
  • Page 5: Figure 4. Application Flow Diagram

    PTX105R/RA2E1 Quick Connect (QC) Demo Quick Start Guide Figure 4. Application Flow Diagram The application starts automatically after the demo kit is powered up. When a card is detected, it performs example data exchange depending on the card type and protocol.
  • Page 6: Running The Example Application

    Figure 6. Import Projects Windows 3. Flash the application. After plugging in the debug micro USB cable, go to Run ⟶ Debug Configurations, double-click on Renesas GDB Hardware Debugging, and setup the debugger (see Figure 4. Click Debug to flash the application on the board.
  • Page 7: Figure 7. Debug Configuration Windows

    PTX105R/RA2E1 Quick Connect (QC) Demo Quick Start Guide Figure 7. Debug Configuration Windows 5. When completed, click Resume twice to start the application (see Figure R35UH0019EU0100 Rev.1.00 Page 7 Sep 25, 2024...
  • Page 8: Figure 8. Application Startup Window

    PTX105R/RA2E1 Quick Connect (QC) Demo Quick Start Guide Figure 8. Application Startup Window 6. To view the application output, open the SEGGER RTT Viewer using device R7FA2E1A9. Figure 9. J-Link RTT Viewer Window R35UH0019EU0100 Rev.1.00 Page 8 Sep 25, 2024...
  • Page 9: Using Iot Reader Library In A Custom Project

    PTX105R/RA2E1 Quick Connect (QC) Demo Quick Start Guide 7. Once the SEGGER terminal is connected, the user can place a card in the field and view the terminal. Figure 10. RTT Viewer Terminals Window 8. Using IoT Reader Library in a Custom Project...
  • Page 10: Integrating The Library In A Custom Project

    Cortex-M23 ■ Cortex-M33 ■ A library for an architecture not shown in the above list may be requested by contacting Renesas technical support. Platform-Specific Implementation As the library is common for all implementations, it must not use any hardware-dependent resources. The PLAT module can be used to define the interface functions to be implemented by the user.
  • Page 11: Ptx105R Qc Schematic

    PTX105R/RA2E1 Quick Connect (QC) Demo Quick Start Guide 9. PTX105R QC Schematic Figure 11. PTX105R-DB-RB QFN56-IOT QC Schematic 10. Revision History Revision Date Description 1.00 Sep 25, 2024 Initial release. R35UH0019EU0100 Rev.1.00 Page 11 Sep 25, 2024...
  • Page 12: Contact Information

    Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products.

This manual is also suitable for:

Ptx105rEk-ra2e1

Table of Contents