STIEBEL ELTRON WPM G Commissioning
Programming unit
Hide thumbs
Also See for WPM G:
- Commissioning (36 pages) ,
- Operation and installation manual (32 pages) ,
- Operation (16 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for STIEBEL ELTRON WPM G
Summary of Contents for STIEBEL ELTRON WPM G
- Page 1 COMMISSIONING Programming unit » WPM G...
-
Page 2: Table Of Contents
Heat-up 24 … „ Compressor settings 24 … „ Circulation pumps 25 … „ Temp. calibration 26 … „ Manual test 26 „ Process data 28 „ Operating mode 30 | WPM G www.stiebel-eltron.com... -
Page 3: General Information
- Room temperature sensor Material losses (appliance damage, consequential losses and environmen- tal pollution) Appliance disposal f This symbol indicates that you have to do something. The ac- tion you need to take is described step by step. www.stiebel-eltron.com WPM G |... -
Page 4: Operation
Setting date and time Note The primary heat pump transfers the date and time set- tings to the secondary heat pumps. f Press the button on the start screen to open the main menu. f Press the button. | WPM G www.stiebel-eltron.com... -
Page 5: Settings For The Safety Concept
The device can be used to monitor the heating system via the internet. For monitoring, you will need an internet connection, a router and the Internet Service Gateway (ISG). Refer to the ISG operating and installation instructions. www.stiebel-eltron.com WPM G |... -
Page 6: Commissioning Cascades
Connect the heat pumps via the connection on the program- ming unit. Observe chapter "Installation / Removing the cas- f Press the button on the start screen to open the main ing parts" in the operating and installation instructions for menu. the heat pump. | WPM G www.stiebel-eltron.com... - Page 7 Alter- to the software ver- sion. native sion of the primary heat pump. f Press the button to return to the main menu. www.stiebel-eltron.com WPM G |...
-
Page 8: Manual Test
Heat pump status … „ Change log „ Operating mode „Alarms In this view, you can see the last 100 active and acknowledged fault messages. The list is updated every minute and every time the appliance is started. | WPM G www.stiebel-eltron.com... -
Page 9: X85; „
Run OTA updates … ……„ With this function, after consulting with Customer Support, you … …„ Room temperature sensor can update your controller software if necessary. f Activate or deactivate the function. www.stiebel-eltron.com WPM G |... - Page 10 (1 = closed, 0 = open) and each combination represents … …„ Hot gas a different mode on the based on the main input mode setting. f Activate or deactivate the function. The mode set from digital inputs will be prioritised over the BMS. | WPM G www.stiebel-eltron.com...
-
Page 11: X85; „
Can be adjusted only if “SG ready” is selected. f Set the room temperature difference at which heating de- mand starts or ends. … …„ Brine pump start signal f Select the input where the signal arrives. www.stiebel-eltron.com WPM G |... -
Page 12: X85; „
Not possible in combination with a room temperature sensor and buffer cylinder type 3. Heating curve … …„ f Adjust the heating curve. … …„ Set flow temperature f Set the temperature to which the flow is heated in Fixed value operation. | WPM G www.stiebel-eltron.com... -
Page 13: X85; „
Pool runtime Can only be activated when the "Pool heating with booster heater" … …„ Pool heating with booster heater … …„ Activate booster heater for pool function is enabled. f Activate or deactivate the function. www.stiebel-eltron.com WPM G |... -
Page 14: X85; „
When the function is activated, the building is cooled passively. … ……„ Set cooling temperature The corresponding symbol appears in the main menu. The symbol f Set the flow temperature for cooling mode. allows you quick access to this menu. | WPM G www.stiebel-eltron.com... -
Page 15: X85; „
Activate or deactivate the function. f Set a time after which a fault message is displayed on the device. When this function is activated, the hot water in DHW cylinder is heated further with the booster heater. www.stiebel-eltron.com WPM G |... -
Page 16: X85; „
Set a time after which a fault message is displayed on the heat pump. device. Alarm limit … …„ f Set a temperature which will trigger the display of a fault message on the device when undershot. | WPM G www.stiebel-eltron.com... -
Page 17: X85; „
Room temperature sensor influence When the function is activated, hot gas can be used for DHW … ……„ Subject to heating season heating. … ……„ Seasonal heating temperature … ……„ Set cooling temperature … ……„ Cooling subject to season www.stiebel-eltron.com WPM G |... - Page 18 Adjust the heating curve. f Activate or deactivate the function. … ……„ Min. flow … ……„ Subject to heating season f Set the minimum temperature for the system flow. f Activate or deactivate the function. | WPM G www.stiebel-eltron.com...
-
Page 19: X85; „
BM card. An un- … ……„ Season start-up regulated heating circuit is no longer available. Over- charging the buffer cylinder is allowed. Can only be activated if the heating circuit is used for cooling. www.stiebel-eltron.com WPM G |... -
Page 20: X85; „
Maximum power consumption (per phase) When the function is activated, the contents of the buffer cylinder are heated based on the heating curve. … …„ Activate current limiter Can only be activated when a module is selected. | WPM G www.stiebel-eltron.com... -
Page 21: X85; „
Brine differential alarm limit … …„ Brine inlet monitoring f Activate or deactivate the function. When this function is activated, the device monitors the inlet tem- perature of the brine entering the heat pump. If the temperature www.stiebel-eltron.com WPM G |... -
Page 22: X85; „
Set the temperature to which the rooms will be heated be- tween the set switching time pairs. … ……„ Required comfort temperature f Set the temperature to which the rooms will be heated dur- ing the set switching time pairs. | WPM G www.stiebel-eltron.com... -
Page 23: X85; „
…„ Port number f Input whether the heat pump is being set up as a primary (master) or secondary (slave) heat pump. The port number must be the same for all heat pumps in the cascade. www.stiebel-eltron.com WPM G |... -
Page 24: X85; „
Activate output limitation … ……„ Max. output … …„ Max. system flow temperature … …„ Port number … …„ Max. return temperature Can only be adjusted if the "TCP" Modbus mode is selected. … …„ Compressor start delay | WPM G www.stiebel-eltron.com... -
Page 25: X85; „
Set whether the speed is fixed or variable. … ……„ Max. speed, tap water … …„ Brine pump (WP) Constant mode … ……„ … ……„ Speed control … ……„ Constant mode f Activate or deactivate the function. … ……„ Min. speed www.stiebel-eltron.com WPM G |... -
Page 26: X85; „
The various components can be tested for their func- … …„ Diverter valve, 0=heating 1=DHW tionality. All settings carried out now do not lead to any parameter … …„ Compressor manual mode changes at the heat pump. … …„ Compressor stage setting | WPM G www.stiebel-eltron.com... - Page 27 Set the mixing valve opening level. Can only be adjusted if the "Compressor manual mode" function is activated. f Set the stage at which the compressor should run. … …„ Cooling cylinder diverter valve on/off f Activate or deactivate the function. www.stiebel-eltron.com WPM G |...
-
Page 28: Process Data
Operating data f Set the mixing valve opening level. Operating data Calculated demand (heating) … …„ Pool diverter valve on/off Calculated compressor stage that is required to meet the heat demand f Activate or deactivate the function. | WPM G www.stiebel-eltron.com... - Page 29 °C Year (months 13-24): Consumed Pool: Return °C Year (months 13-24): COP Component status Version information Actual compressor speed Model Circulation pump (HP) Selected heat pump Brine pump (HP) DHW valve Expansion valve opening level Graphs www.stiebel-eltron.com WPM G |...
-
Page 30: Operating Mode
If the primary heat pump is switched off, the secondary heat pumps are also switched off. If the secondary heat pump is switched off, the status is sent to the primary heat pump. | WPM G www.stiebel-eltron.com... - Page 31 NOTES www.stiebel-eltron.com WPM G |...
- Page 32 Co m f o r t t h r o u gh Te c h n o l o g y STIEBEL ELTRON GmbH & Co. KG Dr.-Stiebel-Straße 33 | 37603 Holzminden | Germany info@stiebel-eltron.com | www.stiebel-eltron.com 4 < A M H C M O = e b e i i j >...
Need help?
Do you have a question about the WPM G and is the answer not in the manual?
Questions and answers