STIEBEL ELTRON WPM G Operation And Installation Manual
  1. Manuals
  2. Brands
  3. STIEBEL ELTRON Manuals
  4. Motherboard
  5. WPM G
  6. Operation and installation manual
STIEBEL ELTRON WPM G Operation And Installation Manual

STIEBEL ELTRON WPM G Operation And Installation Manual

Programming unit
Hide thumbs Also See for WPM G:
Table of Contents

Advertisement

Quick Links

Download this manual
Operation and installation
WPM G
Programming unit
2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WPM G and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for STIEBEL ELTRON WPM G

Summary of Contents for STIEBEL ELTRON WPM G

  • Page 1 Operation and installation WPM G Programming unit...

  • Page 2: Table Of Contents

    Activate functions ..........10 Settings for the safety concept ......10 Setting up remote maintenance......10 Establishing the network connection ....10 Setting up remote maintenance......11 Commissioning cascades........11 5.10 Manual test ............12 6 Menu overview............13 | WPM G www.stiebel-eltron.com...

  • Page 3: General Information

    The appliance is intended for domestic use. It can be used safely tion. by untrained persons. The appliance can also be used in non- domestic environments, e.g. in small businesses, as long as it is used in the same way. www.stiebel-eltron.com WPM G |...

  • Page 4: General Safety Instructions

    Call up main menu 22,0° Call up start screen Access to extended settings and displays. Author- isation code required D0000084929 [WPM G] Confirm settings 1 Sidebar 2 Information on the heat Unconfirmed settings are reset to the previous pumps in the system value.

  • Page 5: Appliance Status Display

    ð The required language is set. Setting date and time The heat pump is prevented from starting. The re- maining period of inhibition is shown. The primary heat pump transfers the date and time settings to the secondary heat pumps. www.stiebel-eltron.com WPM G |...

  • Page 6: Adjusting The Display Settings

    (see Adjusting the heating Heating curve u Adjust the heating curve ( Adjusting the curve [} 7] ). heating curve [} 7] ). Season start-up u Set the outside temperature from which (cooling) the rooms will be cooled. | WPM G www.stiebel-eltron.com...

  • Page 7: Adjusting The Heating Curve

    A change of temperature cannot be made in this Reset to factory settings way at the primary heat pump of a cascade. The values on the current menu page are reset to the factory settings. u Tap the screen to exit the screensaver. www.stiebel-eltron.com WPM G |...

  • Page 8: Adjusting The Dhw Settings

    Activate room temperat- u Switch the function on or off. ure sensor u Further switching time pairs for other days can be set on the following pages u Tap the "Activate" symbol. | WPM G www.stiebel-eltron.com...

  • Page 9: Selecting The Operating Mode

    Tap "Access". external auxiliary ð A number field is displayed. heater) u Enter the access code 607080 and confirm the entry. u Confirm the selection. ð Safe mode is activated. www.stiebel-eltron.com WPM G |...

  • Page 10: Setting The Language

    5.7.2.1 Opening network settings Settings for the safety concept are required for heat pumps with u Tap the "Menu" button on the start screen to open the main an external safety concept (air routing to outdoors). menu. | WPM G www.stiebel-eltron.com...

  • Page 11: Setting Up Remote Maintenance

    If you want to set up monitoring via the inter- menu. net, observe the example "With external net- ð Remote maintenance is set up. work connection (for cascades with one or more secondary heat pumps)". www.stiebel-eltron.com WPM G |...

  • Page 12: Manual Test

    If one of the following messages appears, the primary heat pump will no longer control the corresponding secondary heat u Tap the "Menu" button on the start screen to open the main pump for the duration of the message. menu. u Tap "Settings". | WPM G www.stiebel-eltron.com...

  • Page 13: Menu Overview

    The controller allows you to export log files that can be read on a computer. When logging is running, the data is recorded dir- ectly onto the USB stick and not on the internal memory. Older data is not displaced. www.stiebel-eltron.com WPM G |...
  • Page 14 When the function is activated, the settings made apply to the The operating mode set from the digital inputs is prioritised corresponding heating circuit. The corresponding symbol ap- over BMS. pears in the main menu. | WPM G www.stiebel-eltron.com...
  • Page 15 Not possible in combination with a room temperature sensor and buffer cylinder type 3. ¨¨n Heating/heating circuit 1 ¨¨¨n Activate alarm system flow ¨¨¨n Heating mode u Activate or deactivate the function. u Activate or deactivate the function. www.stiebel-eltron.com WPM G |...
  • Page 16 ¨¨¨n Max. flow The heat pump charges the buffer cylinder. An u Set the maximum flow temperature. auxiliary heater is allowed. Overcharging the buf- fer cylinder is allowed. | WPM G www.stiebel-eltron.com...

  • Page 17: Active Cooling

    The corresponding symbol appears in the main menu. The sym- bol allows you quick access to this menu. ¨¨¨n Emergency/auxiliary heater start offset u Activate or deactivate the function. Can only be adjusted if the "Start at fixed temperature offset" function is activated. www.stiebel-eltron.com WPM G |...
  • Page 18 If the measured room temperature is above the required room > 100 Slower control characteristics temperature plus offset room temperature sensor passive cool- ing, passive cooling is enabled. A prerequisite for this is that cooling season is active. | WPM G www.stiebel-eltron.com...
  • Page 19 Set the speed at which a switch-off signal is to be sent to ¨n Dynamic allocation of inputs/outputs the fan for recooling. The dynamic allocation allows the function to be changed to se- lected digital inputs and relays of the BM card and/or the EM3 card. www.stiebel-eltron.com WPM G |...

  • Page 20: Flow Switch

    Can only be set when the "System DHW mode" function is activ- u Set how long the heat pump is responsible for swimming ated. pool heating when there is a swimming pool demand. u Activate or deactivate the function. | WPM G www.stiebel-eltron.com...

  • Page 21: Alarm Delay

    ¨¨n Set hot gas temperature on the device when undershot. This function prevents ex- cessively low DHW temperatures at the draw-off points. ¨¨n Alarm delay u Set a time after which a fault message is displayed on the device. www.stiebel-eltron.com WPM G |...

  • Page 22: Alarm Limit

    Set how long the auxiliary heater is switched on for before the heat is used. ¨¨n Changeover temperature for cylinder charging with hot ¨¨n Cool-down time u Set how long the auxiliary heater will run on for. | WPM G www.stiebel-eltron.com...
  • Page 23 When this function is activated, a fault message is displayed on u Activate or deactivate the function. the device if the set temperature is undershot. ¨¨¨n Required eco start temperature ¨¨n Evaporation temperature control activated u Activate or deactivate the function. www.stiebel-eltron.com WPM G |...
  • Page 24 Set temperature Temperature to be reached u Set the heat pump port number. Elapsed time How long the program has been run- ning Current stage Current compressor stage at which the heat pump is running | WPM G www.stiebel-eltron.com...
  • Page 25 Set the time after which the compressor will start. ¨¨n Required pool offset - maximum mode Can only be set if "SG Ready" is selected. u Set the pool temperature at which DHW heating starts. www.stiebel-eltron.com WPM G |...
  • Page 26 ¨¨¨n Standby flow u After testing individual components, deactivate u Set the rate at which the pump should run when the com- the respective functions again. pressor is off. | WPM G www.stiebel-eltron.com...

  • Page 27: Auxiliary Heater

    ¨¨n Heat surplus fan u Activate or deactivate the function. u Set the output level at which the cooling fan should run. ¨¨n Auxiliary heater on/off Can only be activated if the "Auxiliary heater" function is switched on. www.stiebel-eltron.com WPM G |...
  • Page 28 ¨¨n Central fault, test signal u Activate or deactivate the function. When this function is activated, the fault message contact is closed and the fault relay is switched. ¨¨n Check high pressure switch Start/Stop u Activate or deactivate the function. | WPM G www.stiebel-eltron.com...

  • Page 29: Process Data" Menu

    Internal emergency/auxiliary heater, stage 3 External brine pump: external brine outlet °C External heat generator For additional heating/cooling circuits °C Active cooling Passive cooling Flow Set flow temperature Return Room Heating season integral component Cooling season integral component www.stiebel-eltron.com WPM G |...

  • Page 30: Operating Mode" Menu

    Year (months 13-24): COP (coefficient of perform- ance) ¨¨n Inverter temperature Pool "Operating mode" menu Day: Delivered Day: Consumed n Operating mode COP (coefficient of performance) See Selecting the operating mode [} 9] Year (months 1-12): Transferred | WPM G www.stiebel-eltron.com...

  • Page 31: Messages

    DHW mode, the auxiliary heater covers the heat demands. u Unlock the screen. u Open the menu. u Tap "Alarms". ð Active alarms are displayed. Acknowledging alarms www.stiebel-eltron.com WPM G |...
  • Page 32 Co m f o r t t h r o u gh Te c h n o l o g y STIEBEL ELTRON GmbH & Co. KG Dr.-Stiebel-Straße 33 | 37603 Holzminden | Germany info@stiebel-eltron.com | www.stiebel-eltron.com 4 0 1 7 2 1 3 4 1 4 8 1 0...

Table of Contents