Summary of Contents for ABI Attachments TR3-E Series
Page 1
Form No. 10-80068 | Rev E | 1/12/2023 Owner’s Manual TR3-E Series Models Property | Equine | Trevor Brazile Editions (6FT/7FT/8FT) NOTE: This Owner’s Manual covers several models. Features may vary by model. Not all features in this manual are applicable to...
TERMS & CONDITIONS “ABI” means ABI Attachments, Inc. 520 S Byrkit Ave, Mishawaka, Indiana 46544, 877.788.7253. The above referenced models are warrantied for 60 months, from the original invoice date, against defects in materials and/or workmanship when put to normal and designed residential, farm, &...
If engaged, disengage power take-off. hydraulic controls in neutral. • and follow all shutdown procedures with genuine ABI Attachments parts • Park on solid, level ground and lower implement to ground • Operate tow vehicle and controls from the driver’s before leaving the operator’s seat to...
USE SEAT BELT AND ROPS result. • ABI Attachments recommends AVOID UNDERGROUND UTILITIES the use of a CAB or roll-over • protective structures (ROPS) and Dig Safe, Call 811 (USA). KEEP RIDERS OFF MACHINERY Read Manual Warning Label seat belt in almost all tow vehicles.
Setup (cont'd) Unpacking Instruction & Setup Initial Setup Instructions 1. Remove bolt (1-1/8” Hex) that secures the Toplink to the Rake attachment from Rake attachment mounting bracket. Tools Needed: Position Toplink end to line up with Rake attachment - Gloves brackets holes and slide bolt thru brackets and Toplink and - Safety Glasses tighten nut (see Figure 1).
Operation Guide • Next, adjust the top link to level out the tool. A good Smaller Tractors: starting point is to have around 1” of thread showing on If the TR3-E is connected to the bottom holes, be sure to CAUTION: Ensure you have at least 9 inches between the If using a smaller tractor without a front end loader, front both ends of the Toplink then turn the top link to contract...
Components • Then, adjust from there to achieve desired surface finish look. Adjustments may be needed accounting for moisture Property Edition changes or vegetation growth in the material. Gage Wheels (tires): The wheels have three operating positions: The bottom hole on the axle block is the standard operation position for general arena maintenance.
Page 9
Components (cont'd) All of the components on the TR3-E are adjustable using the compatible pins. By removing these pins, adjust the components up Trevor Brazile Edition Hydraulic Finish Rake and down within their respective pockets. The Profile Blade (1), Leveling Blade (2), Scarifiers (3), Leveling Blade (4) and Profile Blades (5) all have multiple adjustment positions for fine tuned usage.
Page 10
Scarifying Teeth (Ripping Teeth) Profile Blades The scarifying teeth loosen the ground to eliminate The profile blades are used on the Equine and Trevor hard spots and easily penetrate compacted arena Brazile units and can operate at a depth of up to 4” and are footing and gravel driveway material or soil.
Replacement Parts Grooming Rod Pocket Holes All of the ground engaging components are considered wear parts and will need to be replaced as they wear out from use. To reorder, please contact the ABI Support department at 877-788-7253. Grooming Rods Grooming Rods should be replaced if the rod is bent beyond repair or have worn beyond the ability to function (approximately 11 ½”...
Maintenance Toplink - Be sure to keep the threaded parts of toplinks greased so they don’t seize over time. Finish Rake - Occasionally over the life the tool, bent finger(s) on the finish rake may appear. If this occurs, place a pipe over the bent finger and use the pipe as leverage to straighten the finger back out.
• Profile blades are making a chattering noise when dragged. TR3-E Series - 6FT/7FT/8FT This is probably due to the profile blades not being level. This can cause them to chatter or create waves in the arena. To resolve this issue, double check to make sure the upright towers are vertically level when engaged in the material.
Page 15
ITEM PART # DESCRIPTION ITEM PART # DESCRIPTION 10-10078 TOPLINK, 21" W/LOCK:ZINC 10-20206 NYLOCK NUT:3/4-10:ZINC YEL GR 8 10-10096 LBL:PINCH POINT A 1" X 2" 10-20208 NYLOCK NUT:1/4-20:ZINC GR 5 10-10161 ABI SERIES SERIAL NUMBER PLATE 10-20209 NYLOCK NUT:5/8-11:ZINC CL 10-10444 LABEL: DO NOT PUSH BACKWARDS: TR3 E 10-20220...
Contact Information Customer Support ABI Attachments, Inc Email: support@abiattachments.com 520 S. Byrkit Ave. Phone: 877-788-7253 Mishawaka, IN 46544 Website: www.abisupport.com To order parts or to speak to one of ABI’s Customer Service Representatives contact us Monday to Friday 9am to 5pm EST.
Need help?
Do you have a question about the TR3-E Series and is the answer not in the manual?
Questions and answers