Advertisement
RGCOMBO812 Roll Groover
OPERATOR'S MANUAL
RGCOMBO812
PORTABLE ROLL GROOVER
1425 West Eighth St.
509-59210
REED MANUFACTURING COMPANY
Erie, PA 16502 USA
Phone: 800-666-3691 or 814-452-3691
www.reedmfgco.com
Operator's Manual
Catalog Number: RGCOMBO812
Item Code: 09210
W A R N I N G
Clothing/gloves can
be caught in moving
parts. Fingers can
be crushed.
• • • • • Keep hands away
from grooving
rolls.
• • • • • Use footswitch.
• • • • • Read Operator's
Manual.
Fax: 800-456-1697 or 814-455-1697
1
610-59210
Advertisement
Table of Contents
Related Manuals for REED RGCOMBO812
Summary of Contents for REED RGCOMBO812
- Page 1 RGCOMBO812 Roll Groover Operator's Manual Catalog Number: RGCOMBO812 Item Code: 09210 W A R N I N G Clothing/gloves can be caught in moving parts. Fingers can OPERATOR’S MANUAL be crushed. • • • • • Keep hands away from grooving rolls.
-
Page 2: Description And Specifications
• Reed 5301PD Power Drive (38 rpm Models) with enough force to crush or break bones. RIDGID® is a registered trademark of RIDGID, Inc. and is not associated with Reed Manufacturing Co. 610-59210... - Page 3 Cover up or tie up long hair. Do not wear loose clothing, gloves, unbuttoned jackets, loose sleeve 5. Do not use the RGCOMBO812 Roll Groover for any other cuffs, neckties, rings, watches or other jewelry. purpose than roll grooving pipe and tubing.
- Page 4 Steady the RGCOMBO812 with one hand. Long lengths may require two jacks. 4. With the other hand rotate the RGCOMBO812 drive shaft to 2. Raise the RGCOMBO812 Groove Roll by retracting the Feed align the flats with the jaws on the Power Drive chuck.
- Page 5 RGCOMBO812 Roll Groover Operator's Manual Figure 1 - RGCOMBO812 Roll Groover Adjusting Screw Feed Screw Grease Fittings Crank Shaft Groove Roll Drive Shaft Support Rod Cover Plate Grease Fitting 610-59210...
- Page 6 Operator's Manual RGCOMBO812 Roll Groover Table 1 - Standard Roll Groove Specifications Note: All dimensions are in inches. NOM. PIPE MIN. GASKET GROOVE GROOVE NORMAL PIPE DIAMETER WALL SEAT WIDTH DIAMETER GROOVE SIZE O.D. TOL. THK. ± .030 ± .030 O.D.
- Page 7 RGCOMBO812 Roll Groover Operator's Manual Adjusting Groove Depth 3. With pipe tracking properly and end of pipe against cover plate, Note: To insure the proper groove diameter, a trial groove should step on footswitch and begin advancing Feed Screw with be performed.
-
Page 8: Top View
Operator's Manual RGCOMBO812 Roll Groover Figure 2 - Pipe Set-Up Machine Axis TOP VIEW Pipe Axis Operator's Side Lateral Offset SIDE VIEW Machine Axis Pipe Axis Parallel 610-59210... - Page 9 Tightening Adjusting Screw will increase groove diameter. b. Pipe installed (grooving in place): Verify the pipe hangers Loosening Adjusting Screw will decrease groove diameter. can accommodate the weight of the RGCOMBO812 plus the manual effort required to operate the tool. 4. Forming the Groove 2.
-
Page 10: Parts Breakdown
Operator's Manual RGCOMBO812 Roll Groover Parts Breakdown See Also RP #98 610-59210... -
Page 11: Parts List
RGCOMBO812 Roll Groover Operator's Manual Parts List Ref. No. Description Item Code Quantity Main Body 99205 Gear Housing 99201 Cover Plate 99203 1/4 - 20 x 1/2 Flat Head Socket 30216 Driveshaft 99222 Key 1/4 x 1/4 x 3/4 39208... - Page 12 RGCOMBO812 Roll Groover Operator's Manual Reed Lifetime Warranty Reed Hand Tools are for the professional trade and are warranted against all failure due to defects in workmanship and materials for the normal life of the tool. FAILURES DUE TO MISUSE, ABUSE, OR NORMAL WEAR AND TEAR ARE NOT COVERED BY THIS WARRANTY.
Need help?
Do you have a question about the RGCOMBO812 and is the answer not in the manual?
Questions and answers