Table of Contents
Advertisement
Quick Links
RGCOMBO2 Roll Groover
OPERATOR'S MANUAL
RGCOMBO2
PORTABLE ROLL GROOVER
1425 West Eighth St.
111-59200
REED MANUFACTURING COMPANY
Erie, PA 16502 USA
Phone: 800-666-3691 or 814-452-3691
www.reedmfgco.com
Operator's Manual
Catalog Number: RGCOMBO2
Item Code: 09200
W A R N I N G
Clothing/gloves can
be caught in moving
parts. Fingers can
be crushed.
• • • • • Keep hands away
from grooving
rolls.
• • • • • Use footswitch.
• • • • • Read Operator's
Manual.
Fax: 800-456-1697 or 814-455-1697
1
111-59200
Advertisement
Table of Contents
Related Manuals for REED RGCOMBO2
Summary of Contents for REED RGCOMBO2
- Page 1 RGCOMBO2 Roll Groover Operator's Manual Catalog Number: RGCOMBO2 Item Code: 09200 W A R N I N G Clothing/gloves can be caught in moving parts. Fingers can OPERATOR’S MANUAL be crushed. • • • • • Keep hands away from grooving rolls.
-
Page 2: Description And Specifications
• Reed Model JHV Pipe Jack with JTA Ball Transfer Head, or bones. JH2R Roller Head Jack • Reed Model 2-71 Pipe Reamer • Reed 5301PD Power Drive. RIDGID® is a registered trademark of RIDGID, Inc. and is not associated with Reed Manufacturing Co. 111-59200... -
Page 3: Power Drive Safety
Cover up or tie up long hair. Do not wear loose clothing, gloves, unbuttoned jackets, loose 5. Do not use the RGCOMBO2 Roll Groover for any other sleeve cuffs, neckties, rings, watches or other jewelry. purpose than roll grooving pipe and tubing. - Page 4 Support Rods resting on the Power Drive carriage rails. Steady 6 O.D. the RGCOMBO2 with one hand. 4. With the other hand rotate the RGCOMBO2 drive shaft to align the flats with the jaws on the Power Drive chuck. Pipe Set-Up 5.
- Page 5 RGCOMBO2 Roll Groover Operator's Manual Figure 1 - RGCOMBO2 Roll Groover Adjusting Screw Feed Screw Crank Shaft Grease Fittings Groove Roll Drive Shaft Support Rod Cover Plate Grease Fitting 111-59200...
- Page 6 Operator's Manual RGCOMBO2 Roll Groover Table 1 - Standard Roll Groove Specifications Note: All dimensions are in inches. NOM. PIPE MIN. GASKET GROOVE GROOVE NORMAL PIPE DIAMETER WALL SEAT WIDTH DIAMETER GROOVE ± ± SIZE O.D. TOL. THK. .030 .030 O.D.
- Page 7 RGCOMBO2 Roll Groover Operator's Manual Adjusting Groove Depth 3. With pipe tracking properly and end of pipe against cover plate, Note: To insure the proper groove diameter, a trial groove should step on footswitch and begin advancing Feed Screw with be performed.
- Page 8 Operator's Manual RGCOMBO2 Roll Groover Figure 2 - Pipe Set-Up TOP VIEW Machine Axis Pipe Axis Operator's Side Lateral Offset SIDE VIEW Pipe Axis Machine Axis Parallel 111-59200...
- Page 9 Tightening Adjusting Screw will increase groove diameter. b. Pipe installed (grooving in place): Verify the pipe hangers Loosening Adjusting Screw will decrease groove diameter. can accommodate the weight of the RGCOMBO2 plus the manual effort required to operate the tool. 4. Forming the Groove 2.
-
Page 10: Parts Breakdown
Operator's Manual RGCOMBO2 Roll Groover Parts Breakdown 111-59200 See Also RP #96... -
Page 11: Parts List
RGCOMBO2 Roll Groover Operator's Manual Parts List Ref. No. Description Item Code Quantity Main Body 99200 Gear Housing 99201 Cover Plate 99203 1/4 - 20 x 1/2 Flat Head Socket 30216 Driveshaft 99219 Key 1/4 x 1/4 x 3/4 39208... - Page 12 RGCOMBO2 Roll Groover Operator's Manual Reed Lifetime Warranty Reed Hand Tools are for the professional trade and are warranted against all failure due to defects in workmanship and materials for the normal life of the tool. FAILURES DUE TO MISUSE, ABUSE, OR NORMAL WEAR AND TEAR ARE NOT COVERED BY THIS WARRANTY.
Need help?
Do you have a question about the RGCOMBO2 and is the answer not in the manual?
Questions and answers