Advertisement
Quick Links
TABLETOP TV STAND
INSTRUCTION MANUAL
MODEL
PGTVS30
Thank you for choosing this Perlegear product. We strive to provide you with the best
quality products and service in the industry. If you have any installation questions or issues
with the product, please contact us at the number below.
1-800-456-5231 (US/CA) Mon–Fri, 8am–8pm (CST)
44-808-196-4165 (UK)
Mon–Fri, 2pm–10pm (UTC)
Rev02
support@perlegear.com
www.perlegear.com
Advertisement
Related Manuals for Perlegear PGTVS30
Summary of Contents for Perlegear PGTVS30
- Page 1 MODEL PGTVS30 Thank you for choosing this Perlegear product. We strive to provide you with the best quality products and service in the industry. If you have any installation questions or issues with the product, please contact us at the number below.
- Page 2 K1-1 Tempered Glass Base End Cap Upper Support Pillar Connecting Plate Lower Support Pillar Faceplate Plastic Cover Knob K1-1 Cable Clip Washer Bolt Bolt Plastic Washer Steel Washer Foot Pad...
- Page 3 Compatibility Maximum: 100 x 100mm (3.9 x 3.9″) If this stand is not compatible, please contact our Technical Support line as listed above or Customer Service at support@perlegear.com. WARNING DO NOT exceed the Max load 44 lbs indicated. Use with products heavier...
-
Page 4: Supplied Parts And Hardware
SUPPLIED PARTS AND HARDWARE Washer Spacer x 16 M4/M5 L2.5mm L10mm TV Bolt M4 x 12mm M4 x 30mm M5 x 16mm M5 x 25mm M6 x 15mm M6 x 25mm NOTE: The washers, spacers, and bolts shown above are displayed in accordance with actual size. Tempered End Cap Upper... -
Page 5: Installation
INSTALLATION ATTACHING THE FACEPLATE TO YOUR TV STEP 1 SELECT TV BOLTS Only one bolt size fits your TV. Hand thread bolts into the threaded inserts on the back of your TV to determine which bolt (M4, M5 or M6) to use. We recommend screwing in at least five turns. Do not turn past the bottom of the hole. - Page 6 ATTACH THE FACEPLATE TO YOUR TV CAUTION: • The lever should be positioned toward the top of the TV. CHOOSE THE COMBINATION THAT APPLIES TO YOUR VESA HOLE PATTERN 50 x 50mm (2 x 2″) 75 x 75mm (3 x 3″) 100 x 100mm (3.9 x 3.9″) OPTION A: FOR FLAT BACK TVS Add spacers, if needed, to fit the bolt length and TV back.
- Page 7 OPTION B: FOR CURVED BACK TVS Spacers must be tall enough so that the curved back of the TV does not interfere with the mounting plate. TV Bolt B2 | C2 | D2 Washer A1 | A2 Spacer E | F Alternative Spacer Combinations OPTION C: FOR TVS WITH A BUMP...
- Page 8 OPTION D: FOR TVS WITH PROTRUDING CABLES Use spacers to create extra space between the TV and faceplate. Spacer E | F TV Bolt B2 | C2 | D2 Washer A1 | A2 Alternative Spacer Combinations OPTION E: FOR TVS WITH RECESSED HOLES Spacers need to fill in the recessed holes on the back of the TV, while keeping the faceplate as close to the TV as possible.
- Page 9 CONNECTING THE LOWER SUPPORT PILLAR TO THE BASE STEP 2 Attach the foot pads [W] to the matte side of the tempered glass base [01]. TIP: Leave a small gap between the edge of the glass and the foot pads. Secure the lower support pillar [02d] to the tempered glass base [01].
- Page 10 CONNECTING THE UPPER SUPPORT PILLAR TO THE LOWER STEP 3 SUPPORT PILLAR NOTE: Make sure to install the connecting plate [02c] and upper support pillar [02b] 5/32″ (4mm) correctly as shown below. Allen Key...
- Page 11 ATTACHING THE TV TO THE SUPPORT PILLAR STEP 4 The upper support pillar [02b] has eight height options and the lower support pillar [02d] has five height options. Choose the best height position for your TV before moving on to attach your TV to the pillar.
- Page 12 Hang the TVs on the support pillar. HEAVY! You may need assistance with this step Secure the TVs to the support pillar using the knobs [K].
-
Page 13: Cable Management
CABLE MANAGEMENT STEP 5 K1-1 K1-1 K1-1 K1-1 K1-1 ADJUSTING THE TILT ANGLE OF THE TV STEP 6 Slightly loosen the lever [T]. Adjust the TV to your desired tilt angle. Retighten the lever [T] to lock the tilt angle. Tilt Loosen Loosen... - Page 14 SWIVEL ADJUSTMENT STEP 7 The TV can be swivelled manually. Only swivel the TV by the TV edges. Do not press on the screen. TIP: If the TV is difficult to swivel, remove the TV, then slightly loosen the preassembled nut. Do not overloosen.
- Page 15 LEVELING THE TV STEP 8 Level the TV to your desired angle by hand. Level ROTATION STEP 9 If the VESA holes on the back of your display are perfectly centered, you may rotate the display 360 degrees for portrait mode. CAUTION: Be careful to avoid collision between your TVs when rotating the display for portrait mode or landscape mode.
- Page 16 THANK YOU FOR CHOOSING THIS PERLEGEAR PRODUCT 1-800-456-5231 (US/CA) Mon–Fri, 8am–8pm (CST) support@perlegear.com www.perlegear.com 44-808-196-4165 (UK) Mon–Fri, 2pm–10pm (UTC) 860-01897-00 Rev02...
Need help?
Do you have a question about the PGTVS30 and is the answer not in the manual?
Questions and answers