Page 1
--------------------------------- 01-15 日本語 --------------------------------- 16-30 Thank you for choosing this Perlegear product! At Perlegear we strive to provide you with the best quality products and services in the industry. Should you have any issues, please don't hesitate to contact us at...
• Please read through these instructions completely before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact customer service at support@perlegear.com • Check package contents against Supplied Parts and Hardware List to assure that all components were received undamaged.
Tools Needed (Not lncluded) Phillips Screwdriver Supplied Parts and Hardware Supplied Parts Tube Connector Long Square Short Square Caster Cover Tube Connector Tube Tube 01 (2pcs) 02 (2pcs) 03 (4pcs) 04 (1pc) 05 (1pc) Lower Pole Upper pole Pole Connector with Holes Pole Cover without holes...
Page 5
Secure the Casters to the Square Tubes Step 1 Long Square Short Square Tube Tube Casters Wrench Step1-1 Turn this nut to adjust the height of caster [03] Step1-2 Secure Casters [03] to the square tubes [01] and [02] by using the provided wrench [H] Wrench 35/64 in ( 14mm)
Page 6
Step 3 Secure the Poles [06] and [09] to the Base Lower Pole Tube Connector with Holes Cover Pole Connector Pole Cover M6x10mm Upper Pole Bolt without Holes 5/32 in (4mm) Small Allen Key Warm Tips: It is recommended to wear a pair of gloves to avoid hurting you hands while assembling.
Page 7
Step 4 Secure Square Plate to Upper Pole [09] TV Plate Connector TV Plate & Pad 5/32 in (4mm) Washer Small Allen Key M6x10mm Bolt Slide the TV plate connector and pad [13] over the top of the pole [09] and secure the connector using Small Allen Key [F].
Page 8
Secure the Brackets to the TV TV Bracket TV Bolts Note: The bolts are shown in accordance with the actual size TV1 x4 M4 x 15mm TV2 x4 TV3 x4 M6 x 15mm M6 x 30mm TV4x4 TV5 x4 M8 x 25mm M8 x 50mm Note: The washer and spacers are shown in accordance with the actual size TV7 x4...
Page 9
Spacers [if needed] TV10 13mm Spacer 5mm Spacer 20mm Spacer Select TV Bolts Only one bolt size fits your TV. Bolt length:Verify adequate thread engagement with bolts or bolts/spacers combination. We recommend thread engagement by at least 5 turns. -Too short will not hold the TV. -Too long will damage the TV.
Page 10
Option A (For Flat Back TV) Please note: The bolt hole locations on your TV may vary in accordance of the manufacturers design of the TV. We TV1/TV2/TV4 are only illustrating possible locations of the bolt holes. TV6/TV7 TV8/TV9 (If needed) Alternate Spacer Setups Option B (For Round Back TV) TV1/TV3/TV5...
Page 11
Option C (For TV with A “Bump”) Spacers may be necessary for 2 holes ONLY. TV1/TV3/TV5 TV6/TV7 TV1/TV2/TV4 (If needed) TV6/TV7 TV8/TV9/TV10 TV8/TV9 (If needed) Alternate Spacer Setups Alternate Spacer Setups Option D For cable interference or inset holes, use spacers TV7, TV8 and TV10 to create extra space between the TV and TV brackets Alternate Spacer Setups TV1/TV3/TV5...
Page 12
Hang TV to TV Plate [14] Step 6 6-1 Hang the TV with brackets to the TV plate 6-2 Push the bottom of the TV to TV plate HEAVY! You may need assistance with this step.
Page 13
Step 7 Secure TV to TV Plate [14] Tighten the safety bolt on the bottom of the TV brackets to secure TV to the TV plate. Safety bolt (Not Included) Note: If the TV cart is unstable on a flat ground, you can adjust the pre-assembled nut on the caster until the TV cart is stable.
Page 14
Secure the Shelf [10] to Pole [06] Step 8 Shelf Shelf Support Shelf Support M6x10mm Connecting Plate Bolt 5/32 in (4mm) M6 Nut Small Allen Key Wrench Secure shelf support connecting plate Secure shelf supports [11] to the shelf [10] [12] on the pole [06] using bolts [C] using nuts [E] according to your height need.
Page 15
Step 9 Cables Management Option A Option B...