Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0323
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Read and save these instructions.
Important to Know
1. Read all instructions carefully before installation and
operation.
2. If you are not familiar with state and local electrical codes,
it is recommended that you consult with a qualified
electrician.
3. Before installation, shut off power at the main fuse or
circuit breaker box. Be aware that simply turning off the
wall switch is not sufficient to prevent an electrical shock.
4. This fixture requires a 120 VAC, 60 Hz power source.
5. Do not attempt to take the lantern apart; there are no
serviceable parts inside.
6. To avoid sensor damage by lightning or electrical surge,
make sure the grounding wire is securely connected.
7. For general safety and to avoid any possible damage to
the sensor, be sure the power is switched "off" before
replacing the bulb.
Maximum Wattage: 11W Dimmable LED
Work Temperature: - 4°F~104°F
Wire Nut (F)
Outlet Box
House Grounding Wire
Headless Screw (C)
Fixture Grounding Wire
Cross Bar (A)
Green Grounding Screw (E)
Mounting Screw (B)
Lock Nut (D)
Fig.1
INSTRUCTIONS
TOAVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
Set Screw
Rubber Pad
Back Plate
Fixture Wire
Glass
Clip
Features
1. Energy saving fixture.
2. Use the dim-to-bright illumination option where
you want some minimum illumination through out
the night, such as at your front entrance or garage
door. Use the dark-to-bright illumination option
where you do not need minimum brightness, such
as the backyard or back porch.
3. When in manual override mode, use wall switch
to keep the light ON till dawn.
Hardware Package (included)：
Cross Bar(A)
Green Grounding
Screw (E)
Rubber Pad (H)
Ball Nut (G)
Page 1/4
Mounting Screw (B)
Headless Screw (C)
Wire Nut (F)
Ball Nut (G)
Curved Arm
Fixture
Metal Frame
Lock Nut (D)
Rubber Pad (H)
161028
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Vaxcel Melbourne T0323
Summary of Contents for Vaxcel Melbourne T0323
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0323 WARNING: TOAVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions. Features Important to Know 1.
- Page 2 Installation steps Turn off the power at fuse or circuit box. Thread two headless screws through the cross bar, and then secure them with four lock nuts (two on each side of the cross bar). Adjust the length of the headless screws if necessary. Note: Make sure that the headless screws are lined up horizontally to make the fixture level.
- Page 3 FIG.2 FIG.1 On the back of the sensor Low Level Sens Time Turn wall switch OFF-ON in 3 Seconds Manual AUTO Mode Override Mode Turn wall switch OFF-ON Test 3H 6H in 3 Seconds again CUSTOMIZATION OPTIONS: Shut-off Delay The Shut-off delay is the length of time the light will stay at high-level brightness after motion has ceased to be detected. This Shut-off delay can be set when operation is in 3, 6 or 0 Mode by using the “TIME”...
- Page 4 ---In 3H or 6H Mode, the light is still on full brightness, even though it has been 3 hours or 6 hours after dusk, respectively: 1. Make sure no motion could be picked up by the sensor. 2. Make sure that mode entry is not in manual override. ---After performing 3H or 6H Mode, the light stays on full brightness after 3 minutes: 1.
Need help?
Do you have a question about the Melbourne T0323 and is the answer not in the manual?
Questions and answers