Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0363
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Read and save these instructions.
Important to Know
1. Read all instructions carefully before installation and
operation.
2. If you are not familiar with state and local electrical codes,
it is recommended that you consult with a qualified
electrician.
3. Before installation, shut off power at the main fuse or
circuit breaker box. Be aware that simply turning off the
wall switch is not sufficient to prevent an electrical shock.
4. This fixture requires a 120V AC, 60 Hz power source.
5. Do not attempt to take the lantern apart; there are no
serviceable parts inside.
6. To avoid sensor damage by lightning or electrical surge,
make sure the grounding wire is securely connected.
7. For general safety and to avoid any possible damage to
the sensor, be sure the power is switched "off" before
replacing the bulb.
Maximum Wattage: 60W Incandescent bulb
Work Temperature: -4ºF ~ 104ºF
Headless Screw (D)
Lock Nut (F)
Mounting Plate (A)
House Grounding Wire
Outlet Box
Green Grounding Screw (C)
Fixture Grounding Wire
FIG.1
Metal Frame
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.
Wire Nut (E)
Rubber pad(G)
Ball Nut(H)
Bulb type B Max. 60W
Clip
Outer Glass Shade
Page 1 / 4
Features
1. Energy saving fixture.
2. Use the dim-to-bright illumination option where
you want some minimum illumination through out
the night, such as at your front entrance or
garage door. Use the dark-to-bright illumination
option where you do not need minimum
brightness, such as the backyard or back porch.
3. When in manual override mode, use wall switch
to keep the light ON till dawn.
Hardware Package (included)：
Mounting Plate (A)
Wire Nut (E)
Lock Nut (F)
Back Plate
Fixture Wire
(not include)
Green Grounding
Mounting
Screw (C)
Screw (B)
Rubber Pad (G)
Fixture
Glass Holder
Socket
Inner Glass Shade
Outer Glass Shade
Clip
Ball Nut Kit
Metal Frame
170926
Ball Nut (H)
Advertisement
Related Manuals for Vaxcel T0363
Summary of Contents for Vaxcel T0363
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0363 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER WHILE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions.
- Page 2 Installation Steps Turn off the power at fuse or circuit box. 1. Thread two headless screws through the mounting plate, then secure them with four lock nuts (two on each side of the mounting plate). Adjust the length of the headless screws if necessary. Note: Make sure that the headless screws are lined up horizontally, to ensure that the fixture will be level.
- Page 3 5. Manual Override MODE (nighttime operation only; on at dusk, off at dawn) ● In 3, 6 or 0 mode, to shift to manual override mode, turn off the wall switch in 3 seconds and then turn it on again, the light will turn to high-level brightness at dusk, and turn off automatically at dawn.
- Page 4 Troubleshooting ---If the light does not work at all: 1. Make sure the wall switch and circuit breaker are on. 2. Make sure the wiring connection is correct. 3. Make sure the bulb is not burned out. 4. Cover the sensor with your palm to verify that the ambient light level is not too high. ----In Test Mode, if the light stays on full brightness after 5 seconds: 1.