Advertisement
Quick Links
ASSEMBLY AND INSTALLATION
T0385
WARNING:
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. Read and save these instructions.
Important to Know
1. Read all instructions carefully before installation and operation.
2. If you are not familiar with state and local electrical codes, it is
recommended that you consult with a qualified electrician.
3. Before installation, shut off power at the main fuse or circuit
breaker box. Be aware that simply turning off the wall switch is
not sufficient to prevent an electrical shock.
4. This fixture requires a 120 VAC, 60 Hz power source.
5. Do not attempt to take the lantern apart; there are no
serviceable parts inside.
6. To avoid sensor damage by lightning or electrical surge, make
sure the grounding wire is securely connected.
7. For general safety and to avoid any possible damage to the
sensor, be sure the power is switched "off" before replacing the
bulb.
8. Compatible with LED dimmable bulb.
Maximum Wattage: 60W Incandescent Bulb or 20W LED
dimmable bulb.
Work Temperature: -4°F~104°F
Wire Connector (F)
Outlet Box
House Grounding Wire
Headless Screw (D)
Fixture Grounding Wire
Cross Bar (A)
Green Grounding Screw (C)
Mounting Screw (B)
Lock Nut
INSTRUCTIONS
TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF
POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.
(E)
Features
1. Energy saving fixture.
2. Use the dim-to-bright illumination option where
you want some minimum illumination through out
the night, such as at your front entrance or garage
door. Use the dark-to-bright illumination option
where you do not need minimum brightness, such
as the backyard or back porch.
3. When in manual override mode, use wall switch
to keep the light ON till dawn.
Hardware Package
Cross Bar (A)
Lock Nut (E)
Fixture Wire
Rubber Pad(H)
Ball Nut(G)
Page 1/4
(included):
Mounting Screw (B) Green Grounding
Screw (C)
Ball Nut (G)
Wire Connector (F)
Back Plate
Bulb Type A Max.60W or
20W LED dimmable bulb
(not included)
Headless
Screw (D)
Rubber Pad (H)
Fixture
240703
Advertisement
Related Manuals for Vaxcel T0385
Summary of Contents for Vaxcel T0385
- Page 1 ASSEMBLY AND INSTALLATION INSTRUCTIONS T0385 WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions.
- Page 2 Installation steps Turn off the power at fuse or circuit box. 1. Thread two fixture mounting screws through the cross bar, and then secure them with four lock nuts（ two on each side of the cross bar）.Adjust the length of the fixture mounting screws if necessary. Note: Make sure that the fixture mounting screws are lined up horizontally to make the fixture level.
- Page 3 Fig.1 Fig.2 On the back of the sensor Turn wall switch OFF-ON Time Low Level Sens in 3 Seconds Manual AUTO Mode Override Mode Turn wall switch OFF-ON Test 3H 6H in 3 Seconds again CUSTOMIZATION OPTIONS: Shut-off Delay The Shut-off delay is the length of time the light will stay at high-level brightness after motion has ceased to be detected.This Shut-off delay can be set when operation is in 3, 6 or 0 Mode by using the “TIME”...
- Page 4 Vaxcel reserves the right to repair, replace or issue a credit for any properly installed product, provided it is returned per RMA instruction. This warranty is limited to the cost of the product only and does not extend to transportation, installation or replacement costs.
Need help?
Do you have a question about the T0385 and is the answer not in the manual?
Questions and answers