Page 1
Electric Tiller/Cultivator 3000 Series 3450-01 Operator’s Manual and Safety Instructions for Electric Tiller/Cultivator Original Operating Instructions...
Your safe use of this Mantis product is one of our prime design objectives� Many safety features are built in, but we also rely on your good sense and care to achieve accident-free operation� For best protection, study the manual thoroughly� Learn the proper operation of all controls�...
Page 4
Keep supply flexible cord away from cutting device Cutting device continues to rotate after the prod Cutting device continues to rotate after the prod Cutting device continues to rotate after the prod off. Wait until all machine components ha off. Wait until all machine components hav Cutting device continues to rotate after the prod off.
2. Switch off and disconnect from the power supply if there are malfunctions. Have the tiller/cultivator checked by a qualified professional and repaired, if necessary, before you operate it again� 3� For assistance contact the Mantis customer service center at the number listed on the warranty statement located at the end of these operating instructions �...
Wear tight-fitted protective clothes. Remove plug from the mains immediately if the cable is Contact us at www.mantis.uk.com damaged or cut. Do not expose the product to rain or wet conditions (moisture).
Children must not play with damage. If you find that parts are missing or show damage do not plastic bags, sheets and small parts! There is use the tiller/cultivator but contact the Mantis customer service a danger of choking and suffocation! Handle bar center at the number listed on the warranty statement located at the end of these operating instructions�...
If using an extension cord it must be suitable for outdoor use with sockets protected against water splashing. Make sure the on/off switch is not squeezed or otherwise engaged� Contact us at www.mantis.uk.com Your product is now ready to be used.
Electric Tiller/Cultivator Operation INTENDED USE This tiller/cultivator is intended for loosening and working up the soil in a garden and for tilling coarse soil for mixing in fertilizer, peat and compost in planting areas� This tiller/cultivator should not be used to till extremely dry or wet soil� Wheel adjustment Wheel adjustment Wheel adjustment...
Wait until all machine components have completely stopped before touching the product. supply and let it cool down. I Contact us at www.mantis.uk.com damage! Have any damage re Pay special attention when working on the cutting device! Extensive vibration of the Remove plug from the mains immediately if the cable is damaged or cut.
4� Check for worn or damaged parts� Replace worn parts as necessary Wear protective gloves. Wear eye protection. or contact the Mantis customer service center at 1-800-366-6268 for assistance before using the tiller/cultivator again� Wear a dust mask. Wear protective, slip-resistant footwear.
Nut � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8SFDD-40D Always use only original Mantis replacement parts. The use of any unauthorized replacement parts, attachments or accessories can be dangerous and could cause injury or mechanical damage.
Electric Tiller/Cultivator Maintenance & Storage VIBRATION AND NOISE REDUCTION RESIDUAL RISKS To reduce the impact of noise and vibration emission, limit the time Even if you are operating this tiller/cultivator in accordance of operation, as well as wear personal protective equipment� with all the safety requirements, potential risks of injury and Take the following points into account to minimize the vibration and damage remain.
For assistance contact the Mantis customer service center at the number listed on the warranty statement located at the end of this operating instructions.
Page 16
MANTIS will repair or replace, at its option, any part or parts of the product found to be defective in material or workmanship during the warranty period� Warranty repairs and replacements will be made without charge for parts or labor� All parts replaced under warranty will be considered as part of the original product, and any warranty on the replaced parts will expire coincident with the original product warranty�...
Page 17
DECLARATION OF CONFORMITY Business name of the manufacturer: MANTIS France SARL. full address of the manufacturer: 20, rue des Garennes, 57155 Marly, France name and address of the person (established in the Community) compiled the technical fi le: Robert A. Kurzyna; 20, rue des Garennes, 57155 Marly, France...
Need help?
Do you have a question about the 3000 Series and is the answer not in the manual?
Questions and answers