Advertisement
Advertisement
Table of Contents
Related Manuals for Polytron ACT AT5200
Summary of Contents for Polytron ACT AT5200
- Page 1 ACT AT5200 FTTX Multiport EDFA Quick Reference Guide Revision G...
- Page 2 AT5200 FTTX Multiport EDFA powered by ACT AT5200 Multiport Erbium-Doped Fiber Amplifier Quick Reference Guide ACT Document Number: AT5200 MULTIPORTEDFA-QRG Quick Reference Guide Revision G Copyright © 2017 Ascent Communication Technology Limited. All rights reserved. Reproduction in any manner whatsoever without the express written permission of Ascent Communication Technology is strictly forbidden.
- Page 3 AT5200 FTTX Multiport EDFA powered by Table of Contents 1 Precautions ..........................4 2 Introduction ........................... 5 2.1 Overview ························································································································ 5 2.2 Features ·························································································································· 6 2.3 Specifications ················································································································· 7 2.4 Models and Options ······································································································· 8 3 Installation ..........................9 3.1 Equipment Inventory ····································································································· 9 3.2 Packaging and Transportation ························································································...
- Page 4 AT5200 FTTX Multiport EDFA powered by WARNING! Exposure to class 1M laser radiation is possible. Access should be restricted to trained personnel only. Do not view exposed fiber or connector ends when handling optical equipment. • Ensure adequate cooling and ventilation as specified. The installation and operation manual should be read and understood before units are put into use.
- Page 5 AT5200 FTTX Multiport EDFA powered by AT5200 2RU Erbium-Doped Fiber Amplifier (EDFA) offers a flexible and scalable optical amplification for high quality video transmission in CATV networks. Together with ACT AT5000 series 1550nm transmitter, the AT5200 EDFA provides an ideal video overlay solution in high density FTTX networks to bring the video services to business and home premises.
-
Page 6: Application Diagram
AT5200 FTTX Multiport EDFA powered by • Low noise, high performance with JDSU & IPG pump laser FTTP high power multi-ports optical amplifier with gain spectrum band within 1540 to 1563nm • • Built-in WDM to connect PON OLT Uplink and Combined PON + CATV output •... - Page 7 AT5200 FTTX Multiport EDFA powered by AT5200 EDFA Erbium-Doped Fiber Amplifier - 19” 1 or 2RU Operating CATV Wavelength, nm 1540 to 1563 OLT Pass Wavelength, nm 1310/1490 (signal pass-through) (WDM Optional) CATV Pass Wavelength Loss, dB OLT Pass Wavelength Loss, dB Input Power, dBm -10 to 10, 3dBm typical, -6dBm to 8dBm (constant output) Maximum Output Power, dBm...
- Page 8 AT5200 FTTX Multiport EDFA powered by The maximum output power per port is 26dBm. Output power is measured after WDM. Contact ACT Sales Representative for more information. Solutions Provider for FTTx, RFoG, and HFC www.ascentcomtec.com Page 8 of 24...
- Page 9 AT5200 FTTX Multiport EDFA powered by On receiving your new EDFA, you should carefully unpack and examine the contents for loss or damage that may have occurred during shipping. Refer to warranty registration if loss or damage has occurred. The EDFA pack will consist of the following: Description EDFA, Erbium Doped Fiber Amplifier...
- Page 10 AT5200 FTTX Multiport EDFA powered by The following steps explain how the EDFA is to be installed. Please read them carefully: Unpack the optical amplifier and inspect the unit as stated in Section 3.1. Locate the optical amplifier in a 19” cabinet, ensuring adequate ventilation and space for accessing the rear ports and front-panel keypad.
-
Page 11: Item Description
AT5200 FTTX Multiport EDFA powered by Item Description Status LED GREEN – EDFA works normal. RED – No INPUT or EDFA ERROR (refer to LCD screen for more information ) LASER INPUT LED OPT OUTPUT LED GREEN – Optical Input Normal; No Light – No Optical Input POWER LED GREEN –... - Page 12 AT5200 FTTX Multiport EDFA powered by Item Description Operation Fan vent. IEC Main Input Power 1 Mains input power, 90 to 265 Vac, 50 / 60 Hz, fused IEC input, includes spare fuse. Or 30 to 72 VDC input. Inputs 1 to 2 for power redundancy.
- Page 13 AT5200 FTTX Multiport EDFA powered by The EDFA comprises an Optical Gain Block, Control Board, and serial interface. The Optical Gain Block consists of an Erbium Doped Fiber in conjunction with single or dual 980 nm pump lasers for high optical power efficiency. The Control Board monitors and controls the Optical Gain Block and feeds the front-panel LED indicators as shown in Section 3.5.
- Page 14 AT5200 FTTX Multiport EDFA powered by The EDFA alarm system is designed to generate only urgent alarms. This is due to the importance of the EDFA, as this module will usually drive a large portion of the optical distribution network. Working status indication (LED) is next to the power switch in the front panel.
- Page 15 AT5200 FTTX Multiport EDFA powered by The EDFA’s software is fully automatic and constantly monitors key parameters. These parameters are stored in the unit’s EEPROM and/or microcontroller. Some may be changed via external communications. The unit is designed for local and remote monitoring and control. Factory Defaults / EEPROM Settings The software uses EEPROM for memory back up of the lower and upper alarm limits for analogue parameters and for control variables as set by the user.
- Page 16 AT5200 FTTX Multiport EDFA powered by Each Output Read-only menu, tells the each output of EDFA in dBm. PA Current Read-only menu, tells the pre pump current of EDFA PA Temp Read-only menu, tells the pre pump temperature of EDFA BA Current Read-only menu, display the multi-mode amplify current of EDFA Unit Temp...
- Page 17 AT5200 FTTX Multiport EDFA powered by 3. Set the IP address Select the menu that need modification, press button enter into sub menu, then press button enter into menu modify status, press▲/▼button to increase/decrease the value, press button to shift the value, at last bit press button to save, and press button back to ...
-
Page 18: Pin Assignment
AT5200 FTTX Multiport EDFA powered by Pin Assignment When network management reticle (RJ-45 connector in each side) connects NMS PC and AT- 52-EDFA series directly, it should use straight reticle. See Figure below: RJ-45 connector straight through connecting Workstation port Input receive data+ Output transmit data+ Input receive data-... -
Page 19: Port Description
AT5200 FTTX Multiport EDFA powered by 2) Prepare a twisted pair Ethernet cable with RJ-45 plugs on each end. Use Cat 3, 4 or 5 cable for standard 10Mbps Ethernet connections, or Cat 5 cable for 100Mbps Fast Ethernet connections. 3) Plug one end of the cable into the PC's NIC and plug the other end into any RJ-45 port of the AT-52-EDFA series. - Page 20 AT5200 FTTX Multiport EDFA powered by Pin Assignment DB9/RS232 pin assignment Distribution RXD: accepting of data TXD: transmitter data SG: signal Pin information Port connection AT-52-EDFA series is equipped with a cable to connect AT-52-EDFA series serial port. This cable has a DB9 connector in AT-52-EDFA series and PC side.
- Page 21 AT5200 FTTX Multiport EDFA powered by Direct connect EDFA and computer by ETH cable, set the computer IP address in same sub domain with EDFA. Turn on EDFA, and open browser. Type the EDFA’s IP address (factory default IP address is: 192.168.1.50) into the browser, and then the login page will pop up for “username”...
- Page 22 AT5200 FTTX Multiport EDFA powered by Solutions Provider for FTTx, RFoG, and HFC www.ascentcomtec.com Page 22 of 24...
- Page 23 AT5200 FTTX Multiport EDFA powered by Any time the fiber leads to the amplifier are disconnected, there is the potential for contamination of the ends of the fiber connectors. Dirt or other contaminants on these components can reduce the amplifier’s performance and can result in permanent damage to the device.
- Page 24 AT5200 FTTX Multiport EDFA powered by GERMANY Langwiesenweg 64-71 75323 Bad Wildbad, GERMANY Phone: +49 (0) 7081 / 17 02 0 WEB: www.polytron.de Ascent Communication Technology Ltd AUSTRALIA HONG KONG SAR 140 William Street, Melbourne Unit 9, 12 Floor, Wing Tuck Commercial Centre...
Need help?
Do you have a question about the ACT AT5200 and is the answer not in the manual?
Questions and answers