Supermicro AS -4125GS-TNRT Disassembly Instructions Manual
  1. Manuals
  2. Brands
  3. Supermicro Manuals
  4. Enclosure
  5. AS -4125GS-TNRT
  6. Disassembly instructions manual
Supermicro AS -4125GS-TNRT Disassembly Instructions Manual

Supermicro AS -4125GS-TNRT Disassembly Instructions Manual

Hide thumbs Also See for AS -4125GS-TNRT:
Table of Contents

Advertisement

Quick Links

Download this manual
WEEE DISASSEMBLY INSTRUCTIONS
SUPERMICRO AS -4125GS-TNRT ENCLOSURE
Abstract
This document provides clear guidance for end-of-life recyclers on how to identify
and disassemble reportable materials in compliance with the Waste Electrical and
Electronic Equipment (WEEE) directive.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AS -4125GS-TNRT and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Supermicro AS -4125GS-TNRT

Summary of Contents for Supermicro AS -4125GS-TNRT

  • Page 1 WEEE DISASSEMBLY INSTRUCTIONS SUPERMICRO AS -4125GS-TNRT ENCLOSURE Abstract This document provides clear guidance for end-of-life recyclers on how to identify and disassemble reportable materials in compliance with the Waste Electrical and Electronic Equipment (WEEE) directive.

  • Page 2: Table Of Contents

    Table of Contents Product Views ............................1 Reportable Materials on AS -4125GS-TNRT ..................... 3 Disassemble Instructions .......................... 4 Step-by-Step Disassembly Instructions ..................6 Removing Cable and Chassis Top Cover ..................6 Removing Hard Disk Drive (HDD) / Solid State Drive (SDD) ............7 Removing Power Supply .......................

  • Page 3: Product Views

    1. Product Views Front view Rear view Product construct view Hard Disk Drive/ Solid State Drive Backplane Fans...
  • Page 4 Power Supply GPU Add-On Module Motherboard DIMM Processor...

  • Page 5: Reportable Materials On As -4125Gs-Tnrt

    2. Reportable Materials on AS -4125GS-TNRT According to Article 8(2) and Annex VII of WEEE directive 2012/19/EU, below materials and components should be selectively treated. Description Notes Quantity Printed Circuit Boards (PCB) or With a surface greater than 10 sq cm 2.3, 3.5, 4.1, 6.2, 7.1, 8.1,...

  • Page 6: Disassemble Instructions

    3. Disassemble Instructions The intent of this document is to provide guidance to recyclers on the presence of materials and components at the product / family level, as required by the EU WEEE Directive 2012/10/EU. This document should also help direct recyclers to proper methods for removing parts and general product disassembly instructions.
  • Page 7 Chassis Backplane Fans *2 set Screws Motherboard PCIe Expansion Battery Cables Graphics Card *4 Daughterboard Add-On Module Card Power Supply *2 Power Enclosure*4 Screws and Standoff*4 Set Power Supply Module*4...

  • Page 8: Step-By-Step Disassembly Instructions

    Storage Card and CPU Heat Sink *2 Processor *2 Add-On TPM Module DIMM *6 Set 3.3 Step-by-Step Disassembly Instructions 1. Removing Cable and Chassis Top Cover 1. Use the operating system to power down the system. 2. After the system has completely shut-down, disconnect the power cords from the power supply modules.

  • Page 9: Removing Hard Disk Drive (Hdd) / Solid State Drive (Sdd)

    4. The chassis top cover can be lifted off after removing the screws and sliding the cover back and off the system.. Description Description Power Cable Serial Port USB 3.0 Ports PCIe 5.0 x16 FHFL slots BMC LAN Port Chassis VGA Port Top Cover PCIe 5.0 x16 AIOM Slot (NCSI)
  • Page 10 3. Pull and release the locking clasps holding the SSD in place with either a screwdriver flathead or by hand and lift the SSD out from the posts as shown below: 5. Use a cross screwdriver to remove drive enclosure 6.

  • Page 11: Removing Power Supply

    3. Removing Power Supply 1. Press the release tab on the power supply. 2. Use the handle to gently slide the power supply out the back of the chassis. 3. Remove the screw from the enclosure 4. Cut the power leads connected to the fan and lift the main board from the chassis...

  • Page 12: Removing Add-On Module (Aom)

    Use a flathead screwdriver to cut the capacitor adhesive and pin solder. Adhesive Description Power Supply Power Enclosure Fan Cable Power Module PCB Capacitor 4. Removing Add-on Module (AOM) 1. Disconnect the cables attached to the AOM and then lift the AOM out of the chassis and disconnecting from the motherboard in the process.

  • Page 13: Removing Fan

    5. Removing Fan 1. Disconnect the chassis fan from the motherboard fan connectors as shown below. 2. Squeeze the fan tabs as circled in red and lift the fan housing up and out of the chassis for each fan. Description Cooling Fans 6.

  • Page 14: Removing Graphics Cards

    3. Unscrew the 4 screws (circled in red) to remove the backplane from the backplane bracket. Description Backplane Bracket Backplane 7. Removing Graphics Cards 1. Disconnect any cables connecting the graphics card. 2. Unscrew the screws holding each of the graphics card in place (circled in red). 3.

  • Page 15: Removing Pcie Expansion Daughterboard

    3. Lift the graphics card from the system. Description Graphics Card 8. Removing PCIe Expansion daughterboard 1. Ensure that all cables and GPUs are unplugged and removed from the top side of the expansion card. 2. Unscrew the 4 screws (circled in red) and unlock the lock by pulling up (circled in blue) and lift the expansion card up to gain access to the bottom of the card.

  • Page 16: Removing Processor

    4. Remove the Expansion Card from the bracket by removing the 6 screws (circled in red) Description PCIe Expansion daughterboard 9. Removing Processor 1. Removing the PHM (Processor Heatsink Module ) from the motherboard, first shut down the system and unplug the AC power cord from all power supplies 2.
  • Page 17 3. Once the screws have been removed, lift the heatsink module off the socket. 4. Unscrew the three screws holding the force frame in place and lift the force frame to the vertical position. 5. Gently remove the processor from the socket. Note: Please handle the processor with care to avoid damaging it or its pins Description Heat Sink...

  • Page 18: Removing Dimm

    10. Removing DIMM 10.1 1. Hand press both release tabs on the ends of the DIMM module to unlock it 2. Once the DIMM module is loose, remove it from the memory slot Description 10.1 DIMM 11. Removing the M.2 from the Motherboard 1.

  • Page 19: Removing Control Panel

    12.1 12.2 Description 12.1 Motherboard 12.2 Battery 13. Removing Control Panel Remove control panel screw (R and L) from the chassis.
  • Page 20 13.1 13.2 Remove backet screw and hand screw (R and L) from control panel and used hand remove backet mylar. Description 13.1 Control Panel Cover L & R 13.2 MYLAR_L & R When the all the steps are complete, the chassis enclosure can be recycled.

Table of Contents