Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Supermicro AS -2015HS-TNR
Summary of Contents for Supermicro AS -2015HS-TNR
- Page 1 WEEE DISASSEMBLY INSTRUCTIONS SUPERMICRO AS -2015HS-TNR ENCLOSURE Abstract This document provides clear guidance for end-of-life recyclers on how to identify and disassemble reportable materials in compliance with the Waste Electrical and Electronic Equipment (WEEE) directive.
-
Page 2: Table Of Contents
Table of Contents Product Views ............................3 Reportable Materials on AS -2015HS-TNR ....................5 Disassemble Instructions .......................... 6 3.3 Step-by-Step Disassembly Instructions ...................... 8 Removing Cable and Chassis Top Cover ....................8 Removing Hard Disk Drive (HDD) / Solid State Drive (SDD) ..............9 Removing Power Supply ......................... -
Page 3: Product Views
1. Product Views Front view Rear view Product construct view Hard Disk Drive/ Solid State Drive Backplane Fans... - Page 4 Power Supply Riser Card AIOM Card Riser AIOM Cable Bracket Add-On Module Motherboard Processor DIMM...
-
Page 5: Reportable Materials On As -2015Hs-Tnr
2. Reportable Materials on AS -2015HS-TNR According to Article 8(2) and Annex VII of WEEE directive 2012/19/EU, Below materials and components should be selectively treated. Description Notes Quantity With a surface greater than 10 sq cm 2.3, 3.5, 4.1, 5.1, 6.1, 8.1,... -
Page 6: Disassemble Instructions
3. Disassemble Instructions The intent of this document is to provide guidance to recyclers on the presence of materials and components at the product / family level, as required by the EU WEEE Directive 2012/10/EU. This document should also help direct recyclers to proper methods for removing parts and general product disassembly instructions. - Page 7 Chassis Backplane Fans Screws Motherboard, Riser Cards, Backplane, Add- On Module, AIOM Cable Battery Cables Power Supply Air Shroud Power Supply Power Enclosure*2 Screws and Standoff*2 Set Power Supply Module*2...
-
Page 8: Step-By-Step Disassembly Instructions
Storage Card and CPU Heat Sink Processor SSD *6set Add-On Module Network Card *4 DIMM *6Set AIOM Card M.2 *2 3.3 Step-by-Step Disassembly Instructions 1. Removing Cable and Chassis Top Cover 1. Use the operating system to power down the system. 2. -
Page 9: Removing Hard Disk Drive (Hdd) / Solid State Drive (Sdd)
Description Description Power Cable Chassis BMC LAN Port Top Cover USB 3.0 Ports VGA Port PCIe 5.0 x16 AIOM Slot (NCSI) 2. Removing Hard Disk Drive (HDD) / Solid State Drive (SDD) 1. Press the release button to extend the drive carrier handle. 2. - Page 10 4. For a 2.5” drive, unscrew the four screws as shown below and remove the drive from the tray. Screw 5. Use a cross screwdriver to the remove the drive enclosure...
-
Page 11: Removing Power Supply
6. Use a cross screwdriver to remove screws and lift off the PCB Description HDD/ SSD Hard Drive Enclosure Hard Drive PCB 3. Removing Power Supply 1. Press the release tab on the power supply. 2. Use the handle to gently slide the power supply out the back of the chassis. 3. - Page 12 4. Cut the power leads connected to the fan and lift the main board from the chassis Use a flathead screwdriver to cut the capacitor adhesive and pin solder. Adhesive Description Power Supply Power Enclosure Fan Cable Power Module PCB Capacitor...
-
Page 13: Removing Advanced I/O (Aiom) Network Card
4. Removing Advanced I/O (AIOM) Network Card 1. Loosen the thumbscrew (circled in red) using your hand. 2. Slide the AIOM out of the opening. Description AIOM Network Card 5. Removing AIOM Cable 1. Unscrew the two screws (circled in red) using a screwdriver and loosen the thumb screw by hand. 2. -
Page 14: Removing Add-On Module (Aom)
6. Removing Add-on Module (AOM) 1. Loosen the thumbscrew and press down on the push pin. 2. Slide the AOM towards the push pin and lift the AOM out of the system. Thumb Screw Push Pin Description Add-on Module 7. Removing Fan 1. -
Page 15: Removing Backplane
Description Cooling Fans 8. Removing Backplane 1. Ensure all the cables are disconnected and pull the backplane bracket out of the chassis. 2. Unscrew the 6 screws as shown below to remove the backplane from the backplane bracket. Description Backplane 9. -
Page 16: Removing Processor
Description Riser Card Bracket Riser Cards 10. Removing Processor Thumb Screw 1. Removing the PHM (Processor Heatsink Module) from the motherboard, first shut down the system and unplug the AC power cord from all power supplies 2. Use a T30-bit screwdriver to loosen the four peek nuts on the heatsink in the sequence of 6,5,4,3,2,1 as shown in the picture below: 10.1 3. -
Page 17: Removing Dimm
10.2 Note: Please handle the processor with care to avoid damaging it or its pins Description 10.1 Heat Sink 10.2 Processor 11. Removing DIMM 11.1 1. Hand press both release tabs on the ends of the DIMM module to unlock it 2. -
Page 18: Removing The M.2 From The Motherboard
Description Network Card 12.1 13. Removing the M.2 from the Motherboard 1. Locate the M.2 on the motherboard at the J7 connector and press down on the clip holding the M.2 in place. 2. Gently pull the M.2 out of the socket. 13.1 J7 Connector Description... -
Page 19: Removing Motherboard
14.1 Description 14.1 Power Supply Shroud 14.2 Air Shroud 15. Removing Motherboard 1. Unscrew the screws (circled in red) on the motherboard and lift the motherboard out of the chassis. 2. Push aside the small clamp that covers the edge of the battery. When the battery is released, lift it out of the holder. -
Page 20: Removing Control Panel
16. Removing Control Panel Remove control panel screw (R and L) from the chassis. 16.1 16.2 Remove backet screw and hand screw (R and L) from control panel and used hand remove backet mylar. Description 16.1 Control Panel Cover L & R 16.2 MYLAR_L &...
Need help?
Do you have a question about the AS -2015HS-TNR and is the answer not in the manual?
Questions and answers