Supermicro SC847E1C Series User Manual
  1. Manuals
  2. Brands
  3. Supermicro Manuals
  4. Enclosure
  5. SC847E1C Series
  6. User manual

Supermicro SC847E1C Series User Manual

Jbod chassis
Hide thumbs
Table of Contents

Advertisement

Quick Links

S
UPER
®
SC847E1C/2C JBOD
CHASSIS SERIES
C
SC847E1C-R1K28JBOD
SC847E2C-R1K28JBOD
USER'S MANUAL
1.0a

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SC847E1C Series and is the answer not in the manual?

Questions and answers

Related Manuals for Supermicro SC847E1C Series

Summary of Contents for Supermicro SC847E1C Series

  • Page 1 UPER ® SC847E1C/2C JBOD CHASSIS SERIES SC847E1C-R1K28JBOD SC847E2C-R1K28JBOD USER’S MANUAL 1.0a...
  • Page 2 This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except as expressly permitted by the terms of said license.

  • Page 3: Contacting Supermicro

    Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Website: www.supermicro.com Europe Address: Super Micro Computer B.V. Het Sterrenbeeld 28, 5215 ML...
  • Page 4 SC847E1C/2C JBOD Chassis Manual Preface About This Manual This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the SC847EC1/C2 JBOD chassis. Installation and maintenance should be performed by experienced technicians only. This manual lists compatible parts available when this document was published.
  • Page 5 Preface Manual Organization Chapter 1: Introduction The first chapter provides a checklist of the main components included with this chassis and describes the main features of the SC847EC1/C2 chassis. This chapter also includes contact information. Chapter 2: Standardized Warning Statements for AC/DC Systems This chapter lists warnings, precautions, and system safety.
  • Page 6 Supermico website at www.supermicro.com. Appendix B: Power Supply Specifications This chapter lists the specifications of the power supply provided with your chas- sis. For additional information, refer to the Supermicro website at www.supermicro. com. Appendix C: BPN-SAS3-846EL Backplane Specifications This chapter contains information on the BPN-SAS3-846EL1 and BPN-SAS3-EL2 backplanes.

  • Page 7: Table Of Contents

    Preface Table of Contents Contacting Supermicro ..................iii Chapter 1 Introduction Overview ......................1-1 Shipping List ....................1-1 Where to get Replacement Components ............1-2 Returning Merchandise for Service..............1-3 Chapter 2 Standardized Warning Statements for AC/DC Systems About Standardized Warning Statements ............2-1 Warning Definition ...................
  • Page 8 SC847E1C/2C JBOD Chassis Manual System Fans ....................4-6 Power Supply ....................4-8 Installing the Power Card ................4-10 Chapter 5 Rack Installation Overview ......................5-1 Unpacking the System ..................5-1 Preparing for Setup ..................5-1 Choosing a Setup Location ................5-1 Warnings and Precautions ................

  • Page 9: Chapter 1 Introduction

    1280W (Platinum Level) high-efficiency redundant power supply and seven hot-plug redundant cooling fans, the SC847EC1/C2 JBOD is a reliable, high-quality storage workhorse system. Shipping List Please visit the Supermicro website for the latest shiping lists and part numbers for your particular chassis model at www.supermicro.com. SC847E1C/2C JBOD Chassis Model...

  • Page 10: Where To Get Replacement Components

    Supermicro Authorized Distributors/ System Integrators/Resellers. A list of Supermicro Authorized Distributors/System Integrators/Resellers can be found at: http://www.supermicro.com. Click the Where to Buy link.

  • Page 11: Returning Merchandise For Service

    For faster service, RMA authorizations may be requested online (http://www. supermicro.com/support/rma/). Whenever possible, repack the chassis in the original Supermicro carton, using the original packaging material. If these are no longer available, be sure to pack the chassis securely, using packaging material to surround the chassis so that it does not shift within the carton and become damaged during shipping.
  • Page 12 SC847E1C/2C JBOD Chassis Manual Notes...

  • Page 13: Chapter 2 Standardized Warning Statements For Ac/Dc Systems

    Only certified technicians should attempt to install or configure components. Read this appendix in its entirety before installing or configuring components in the Supermicro chassis. These warnings may also be found on our web site at http://www.supermicro.com/ about/policies/safety_information.cfm. Warning Definition Warning! This warning symbol means danger.
  • Page 14 SC847E1C/2C JBOD Chassis Manual Warnung WICHTIGE SICHERHEITSHINWEISE Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut.
  • Page 15 Warning Statements for AC Systems ‫جسذٌة‬ ‫اصابة‬ ً‫تتسبب ف‬ ‫حالة ٌوكي أى‬ ً‫اًك ف‬ ‫خطز‬ ًٌ‫ٌع‬ ‫هذا الزهز‬ !‫تحذٌز‬ ‫الذوائز‬ ‫بالوخاطز الٌاجوة عي‬ ‫ي على علن‬ ، ‫ك‬ ‫هعذات‬ ‫تعول على أي‬ ‫قبل أى‬ ‫الكهزبائٍة‬ ‫حىادث‬ ‫أي‬ ‫وقىع‬ ‫وٌع‬ ‫ل‬ ‫الىقائٍة‬...

  • Page 16: Installation Instructions

    SC847E1C/2C JBOD Chassis Manual Installation Instructions Warning! Read the installation instructions before connecting the system to the power source. 設置手順書 システムを電源に接続する前に、 設置手順書をお読み下さい。 警告 将此系统连接电源前,请先阅读安装说明。 警告 將系統與電源連接前，請先閱讀安裝說明。 Warnung Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen lesen. ¡Advertencia! Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación.

  • Page 17: Circuit Breaker

    Chapter 2: Warning Statements for AC/DC Systems Circuit Breaker Warning! This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 60VDC, 20 A. サーキッ ト ・ ブレーカー この製品は、 短絡 （過電流） 保護装置がある建物での設置を前提としています。 保護装置の定格が60VDC、...

  • Page 18: Power Disconnection Warning

    SC847E1C/2C JBOD Chassis Manual 경고! 이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에 의존합니다. 보호장치의 정격이 반드시 60V(볼트), 20A(암페어)를 초과하지 않도록 해야 합니다. Waarschuwing Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van uw electrische installatie. Controleer of het beveiligde aparaat niet groter gedimensioneerd is dan 60V, 20A.
  • Page 19 Chapter 2: Warning Statements for AC/DC Systems ¡Advertencia! El sistema debe ser disconnected de todas las fuentes de energía y del cable eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso el interior del chasis para instalar o para quitar componentes de sistema. Attention Le système doit être débranché...

  • Page 20: Equipment Installation

    SC847E1C/2C JBOD Chassis Manual Equipment Installation Warning! Only trained and qualified personnel should be allowed to install, replace, or service this equipment. 機器の設置 トレーニングを受け認定された人だけがこの装置の設置、 交換、 またはサービスを許可 されています。 警告 只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。 警告 只有經過受訓且具資格人員才可安裝、更換與維修此設備。 Warnung Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem, qualifiziertem Personal gestattet werden.

  • Page 21: Restricted Area

    Chapter 2: Warning Statements for AC/DC Systems Waarschuwing Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door geschoold en gekwalificeerd personeel. Restricted Area Warning! This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security.

  • Page 22: Battery Handling

    SC847E1C/2C JBOD Chassis Manual ‫אזור עם גישה מוגבלת‬ !‫אזהרה‬ ‫יש להתקין את היחידה באזורים שיש בהם הגבלת גישה. הגישה ניתנת בעזרת‬ .)'‫כלי אבטחה בלבד (מפתח, מנעול וכד‬ ‫محظورة‬ ‫مناطق‬ ٍ‫نتركُبها ف‬ ‫هذه انىحذة‬ ‫تخصيص‬ ‫تم‬ ،‫أداة خاصت‬ ‫من خالل استخذاو‬ ‫فقط‬...
  • Page 23 Chapter 2: Warning Statements for AC/DC Systems Warnung Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers. Attention Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une pile de type semblable ou équivalent, recommandée par le fabricant.

  • Page 24: Redundant Power Supplies

    SC847E1C/2C JBOD Chassis Manual Redundant Power Supplies Warning! This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. 冗長電源装置 このユニッ トは複数の電源装置が接続されている場合があります。 ユニッ トの電源を切るためには、 すべての接続を取り外さなければなりません。 警告 此部件连接的电源可能不止一个，必须将所有电源断开才能停止给该部件供电。 警告 此裝置連接的電源可能不只一個，必須切斷所有電源才能停止對該裝置的供電。 Warnung Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.

  • Page 25: Backplane Voltage

    Chapter 2: Warning Statements for AC/DC Systems ‫امداد الطاقة‬ ‫بوحدات‬ ‫عدة اتصاالت‬ ‫جهاز‬ ‫ال‬ ‫يكون لهذا‬ ‫قد‬ ‫الكهرباء‬ ‫عن‬ ‫وحدة‬ ‫ال‬ ‫لعسل‬ ‫كافة االتصاالت‬ ‫يجب إزالة‬ 경고! 이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에 전원을...

  • Page 26: Comply With Local And National Electrical Codes

    SC847E1C/2C JBOD Chassis Manual ‫מתח בפנל האחורי‬ !‫הרה‬ ‫אז‬ ‫קיימת סכנת מתח בפנל האחורי בזמן תפעול המערכת. יש להיזהר במהלך‬ .‫העבודה‬ ‫اللىحة‬ ‫أوالطاقة المىجىدة على‬ ‫التيار الكهزبائي‬ ‫مه‬ ‫خطز‬ ‫هناك‬ ‫هذا الجهاس‬ ‫خدمة‬ ‫كه حذرا عند‬ ‫يعمل‬ ‫النظام‬ ‫عندما يكىن‬ 경고! 시스템이...

  • Page 27: Product Disposal

    Chapter 2: Warning Statements for AC/DC Systems Attention L'équipement doit être installé conformément aux normes électriques nationales et locales. ‫תיאום חוקי החשמל הארצי‬ !‫אזהרה‬ ‫הציוד חייבת להיות תואמת לחוקי החשמל המקומיים והארציים‬ ‫התקנת‬ ‫المتعلقة‬ ‫المحلية والىطىية‬ ‫قىاويه‬ ‫يجب أن يمتثل لل‬ ‫الكهربائية‬...

  • Page 28: Hot Swap Fan Warning

    SC847E1C/2C JBOD Chassis Manual ¡Advertencia! Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales. Attention La mise au rebut ou le recyclage de ce produit sont généralement soumis à des lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de l'organisme compétent.
  • Page 29 Chapter 2: Warning Statements for AC/DC Systems 警告 當您從機架移除風扇裝置，風扇可能仍在轉動。小心不要將手指、螺絲起子和其他 物品太靠近風扇。 Warnung Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände von den Öffnungen des Lüftergehäuses entfernt. ¡Advertencia! Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador del chasis.

  • Page 30: Dc Power Supply

    SC847E1C/2C JBOD Chassis Manual DC Power Supply Warning! When stranded wiring is required, use approved wiring terminations, such as closedloop or spade-type with upturned lugs. These terminations should be the appropriate size for the wires and should clamp both the insulation and conductor. 警告...
  • Page 31 Chapter 2: Warning Statements for AC/DC Systems Attention Quand des fils torsadés sont nécessaires, utiliser des douilles terminales homologuées telles que celles à circuit fermé ou du type à plage ouverte avec cosses rebroussées. Ces douilles terminales doivent être de la taille qui convient aux fils et doivent être refermées sur la gaine isolante et sur le conducteur.

  • Page 32: Dc Power Disconnection

    SC847E1C/2C JBOD Chassis Manual DC Power Disconnection Warning! Before performing any of the following procedures, ensure that power is removed from the DC circuit. 警告 次の手順を開始する前に、 DC回路から電源が切断されているこ とを確認してく ださい。 警告 進行以下任一操作程序前，請確保直流電路已斷電。 警告 请在进行以下任一操作程序前，确保直流电路的电源已经断开。 Warnung Vor Ausführung der folgenden Vorgänge ist sicherzustellen, daß die Gleichstromschaltung keinen Strom erhält.

  • Page 33: Hazardous Voltage Or Energy Present On Dc Power Terminals

    Chapter 2: Warning Statements for AC/DC Systems 주의! 다음 절차들을 수행하기 전에, 전원이 DC회로로부터 제거되었는지를 확인해 주십시오. Waarshuwing Wanneer geslagen bedrading vereist is, dient u bedrading te gebruiken die voorzien is van goedgekeurde aansluitingspunten, zoals het gesloten-lus type of het grijperschop type waarbij de aansluitpunten omhoog wijzen.
  • Page 34 SC847E1C/2C JBOD Chassis Manual ¡Advertencia! Puede haber energía o voltaje peligrosos en los terminales eléctricos de CC. Reemplace siempre la cubierta cuando no estén utilizándose los terminales. Asegúrese de que no haya acceso a conductores descubiertos cuando la cubierta esté colocada. Attention Le voltage ou l'énergie électrique des terminaux à...

  • Page 35: Chapter 3 System Interface

    Chapter 3: System Interface Chapter 3 System Interface Overview There are several LEDs on the control panel as well as others on the drive carri- ers to keep you constantly informed of the overall status of the system as well as the activity and health of specific components.

  • Page 36: Control Panel Buttons

    SC847E1C/2C JBOD Chassis Manual Control Panel Buttons There are two push-buttons located on the left handle of the chassis. These are (in order from top to bottom) a power on/off button and a reset button. Power: The main power button is used to apply or remove power from the power supply to the server system.
  • Page 37 Chapter 3: System Interface Informational LED Status Description An overheat condition has occured. Solid red (This may be caused by cable congestion). Fan failure, check for an inoperative fan. Blinking red (1Hz) Power failure, check for a non-operational Blinking red (0.25Hz) power supply.

  • Page 38: Drive Carrier Leds

    SC847E1C/2C JBOD Chassis Manual Drive Carrier LEDs The SC847E1C/2C JBOD chassis uses SAS or SATA drives. SAS/SATA Drives Each SAS/SATA drive carrier has one set of LEDs, with one blue and red LED indicator for each drive. The LEDs function as follows: Blue Drive Carrier LED Indicator Color Status...

  • Page 39: Chapter 4 Chassis Setup And Maintenance

    Chapter 4: Chassis Setup and Maintenance Chapter 4 Chassis Setup and Maintenance Overview This chapter covers the steps required to install components and perform mainte- nance on the chassis. The only tool you will need to install components and perform maintenance is a Phillips screwdriver.

  • Page 40: Removing The Chassis Cover

    SC847E1C/2C JBOD Chassis Manual Removing the Chassis Cover Figure 4-1: Removing the Chassis Cover Removing the Chassis Cover 1. Power down the system and remove the power cords from the rear of the power supplies. 2. Remove the screws securing the cover to the chassis. 3.

  • Page 41: Installing Removable Hard Drives

    Chapter 4: Chassis Setup and Maintenance Installing Removable Hard Drives Figure 4-2: Removing a Hard Drive Carrier The SC847EC1/C2 JBOD chassis has hot-swappable hard drives which may be removed from the chassis without powering down the system. Removing Hard Drive Carriers from the Chassis 1.
  • Page 42 Figure 4-4: Removing the Dummy Drive from the Carrier Warning! Enterprise level hard disk drives are recommended for use in Supermicro chassis and servers. For information on recommended HDDs, visit the Supermicro Web site at http://www.supermicro.com/products/nfo/storage.cfm...
  • Page 43 Chapter 4: Chassis Setup and Maintenance SAS/SATA Hard Drive Drive Carrier Figure 4-5: Installing the Hard Drive into the Carrier 2. Slide the hard drive into the carrier with the printed circuit board side facing down. 3. Carefully align the mounting holes in both the drive carrier and the hard drive. 4.

  • Page 44: System Fans

    SC847E1C/2C JBOD Chassis Manual System Fans Seven hot-swappable, heavy-duty fans provide cooling for the chassis. These fans circulate air through the chassis thereby lowering the chassis internal tempera- ture. Release Tab Air Direction Indicator Figure 4-7: System Fan Replacing a System Fan 1.
  • Page 45 Chapter 4: Chassis Setup and Maintenance Figure 4-8: Placing a System Fan in the Chassis...

  • Page 46: Power Supply

    An illuminated green light indicates that the power supply is operating. Redundant power supplies are hot-swappable, and can be changed without pow- ering down the system. New units can be ordered directly from Supermicro (see contact information in the Preface). Release Tab...
  • Page 47 Chapter 4: Chassis Setup and Maintenance Figure 4-10: Power Supply Release Tab 4. Replace the failed power module with the same model. 5. Push the new power supply module into the power bay until you hear a click. 6. If using only one power supply, plug the AC power cord back into the module and power up the server.
  • Page 48 SC847E1C/2C JBOD Chassis Manual Removing and Installing the Backplanes The SC847E1C/2C chassis comes equipped with a BPN-SAS3-846EL1/EL2 front backplane and a BPN-SAS3-826EL1/EL2 rear backplane. For detailed infomation and instructions on how to change the backplane settings, see Appendices C and D of this manual.
  • Page 49 Chapter 4: Chassis Setup and Maintenance Removing the Rear Backplane 1. Power down the system and remove the power cords from the rear of the power supplies. Remove the chassis cover as described in Section 4-2. 2. Remove the two side screws (one on each side of the chassis) which secure the rear tray to the chassis.
  • Page 50 SC847E1C/2C JBOD Chassis Manual Installing the Front Backplane 1. Confirm that the power cords are still disconnected from the power supplies. 2. Place the front backplane in the chassis. Figure 4-15: Installing the Front Backplane 3. Install the two side screws to secure the front backplane to the chassis. 4.
  • Page 51 Chapter 4: Chassis Setup and Maintenance Installing the Rear Backplane 1. Confirm that the power cords are still disconnected from the power supplies. 2. Slide the rear tray out of the back of the chassis. Figure 4-17: Installing the Rear Backplane 3.

  • Page 52: Installing The Power Card

    SC847E1C/2C JBOD Chassis Manual Installing the Power Card Figure 4-19: Installing the CSE-PTJBOD-CB3 Power Card into the Chassis Removing the Power Card From the Chassis 1. Power down the system and remove the power cords from the rear of the power supplies.

  • Page 53: Chapter 5 Rack Installation

    Chapter 5: Rack Installation Chapter 5 Rack Installation Overview This chapter provides a quick setup checklist to get your chassis up and running. Following these steps in the order given should enable you to have the system operational within a minimal amount of time. Unpacking the System You should inspect the box which the chassis was shipped in and note if it was damaged in any way.

  • Page 54: Warnings And Precautions

    SC847E1C/2C JBOD Chassis Manual Warnings and Precautions Rack Precautions • Ensure that the leveling jacks on the bottom of the rack are fully extended to the floor with the full weight of the rack resting on them. • In single rack installations, stabilizers should be attached to the rack. •...

  • Page 55: Rack Mounting Considerations

    Chapter 5: Rack Installation Rack Mounting Considerations Ambient Operating Temperature If installed in a closed or multi-unit rack assembly, the ambient operating tempera- ture of the rack environment may be greater than the ambient temperature of the room. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturer’s maximum rated ambient tempera- ture (TMRA).

  • Page 56: Rack Mounting Instructions

    SC847E1C/2C JBOD Chassis Manual Rack Mounting Instructions This section provides information on installing the chassis into a rack unit with the rails provided. There are a variety of rack units on the market, which may mean that the assembly procedure will differ slightly from the instructions provided. You should also refer to the installation instructions that came with the rack unit you are using.

  • Page 57: Locking Tabs

    Chapter 5: Rack Installation Locking Tabs Each inner rail has a locking tab. This tab locks the chassis into place when installed and pushed fully into the rack. These tabs also lock the chassis in place when fully extended from the rack. This prevents the server from coming completely out of the rack when when the chassis is pulled out for servicing.

  • Page 58: Installing The Inner Rails On The Chassis

    SC847E1C/2C JBOD Chassis Manual Inner Rails Figure 5-3: Installing the Inner Rails Figure 5-4: Inner Rails Installed on the Chassis Installing The Inner Rails on the Chassis Installing the Inner Rails 1. Confirm that the left and right inner rails have been correctly identified. Place the inner rail firmly against the side of the chassis, aligning the hooks on the side of the chassis with the holes in the inner rail.

  • Page 59: Installing The Outer Rails On The Rack

    Chapter 5: Rack Installation L-min=676.00(26.61")(outer rail) 21D01 Figure 5-5: Extending and Releasing the Outer Rails Installing the Outer Rails on the Rack Installing the Outer Rails 1. Press upward on the locking tab at the rear end of the middle rail. 2.

  • Page 60: Standard Chassis Installation

    SC847E1C/2C JBOD Chassis Manual Ball-Bearing Shuttle Figure 5-6: Installing into a Rack Note: figures are for illustrative purposes only. Always install servers into racks from the bottom up. Standard Chassis Installation Installing the Chassis into a Rack 1. Confirm that the inner rails are properly installed on the chassis. 2.

  • Page 61: Optional Quick Installation Method

    Chapter 5: Rack Installation Optional Quick Installation Method The following quick installation method may be used to install the chassis onto a rack. Installing the Chassis into a Rack 1. Install the whole rail assembly onto the rack as described on page 5-7. 2.
  • Page 62 SC847E1C/2C JBOD Chassis Manual Notes 5-10...

  • Page 63: Appendix A Sc847E1C/2C Jbod Cables And Hardware

    This appendix lists supported cables for your chassis system. It only includes the most commonly used components and configurations. For more compatible cables, refer to the manufacturer of the motherboard you are using and our Web site at: www.supermicro.com. A-2 Cables Included with SC847E1C/2C JBOD Chassis SC847E1C/2C-R1K28JBOD...
  • Page 64 SC847E1C/2C JBOD Chassis Manual Extending Power Cables Although Supermicro chassis are designed with to be efficient and cost-effective, some compatible motherboards have power connectors located in different areas. To use these motherboards you may have to extend the power cables to the mother boards.
  • Page 65 Appendix A: Chassis Cables Chassis Screws The accessory box includes all the screws needed to set up your chassis. This section lists and describes the most common screws used. Your chassis may not require all the parts listed. HARD DRIVE Flat head Pan head 6-32 x 5 mm...
  • Page 66 SC847E1C/2C JBOD Chassis Manual Notes...

  • Page 67: Appendix B Sc847E1C/2C Jbod Power Supply Specifications

    Appendix B: Power Supply Specifications Appendix B SC847E1C/2C JBOD Power Supply Specifications This appendix lists power supply specifications for your chassis system. SC847E1C/2C-R1K28JBOD 1280W MFR Part # PWS-1K28P-SQ 1000W Output @ 100-140V, 12-8A, 50-60Hz AC Input 1280W Output @ 180-240V, 8-6A, 50-60Hz 1000W: +12V/83A;...
  • Page 68 SC847E1C/2C JBOD Chassis Manual Notes...

  • Page 69: Appendix C Bpn-Sas3-846El Backplane Specifications

    Appendix C BPN-SAS3-846EL Backplane Specifications Appendix C BPN-SAS3-846EL Backplane Specifications To avoid personal injury and property damage, carefully follow all the safety steps listed below when accessing your system or handling the components. C-1 ESD Safety Guidelines Electrostatic Discharge (ESD) can damage electronic com ponents. To prevent dam- age to your system, it is important to handle it very carefully.
  • Page 70 This manual reflects BPN-SAS3-846EL Revision 1.01, the most current release available at the time of publication. Always refer to the Supermicro Web site at www.supermicro.com for the latest updates, compatible parts and supported con- figurations.
  • Page 71 Appendix C BPN-SAS3-846EL Backplane Specifications C-6 Front Connectors MH14 MH15 Q866 EXP I2C4 Q872 EXP I2C0 MH13 Q871 MH16 Q870 LED Testing Only ACTLED 12V_LED1 P_UART Q873 S_SDB BC57 Q867 BC29 Q869 C177 BC10 P_MDIO P_SDB MH17 S_MDIO C165 C107 OVERHEATFAIL1 C233 C236 C206...
  • Page 72 SC847E1C/2C JBOD Chassis Manual C-7 Front Connector and Pin Definitions 1. - 2. Primary and Secondary Expander Chips The primary and secondary expander chips allow the backplane to support dual port, cas- cading, and failover configurations. 3. Backplane Power Connectors Backplane Main Power The 4-pin connectors, designated PWR1 -...
  • Page 73 Appendix C BPN-SAS3-846EL Backplane Specifications C-8 Front Jumper Location and Settings LED Testing Only ACTLED MH14 MH15 Q866 EXP I2C4 MH13 Q872 MH16 EXP I2C0 Q871 LED Testing Only Q870 ACTLED 12V_LED1 P_UART Q873 S_SDB BC57 Q867 BC29 Q869 C177 BC10 P_MDIO P_SDB...
  • Page 74 SC847E1C/2C JBOD Chassis Manual C-9 Front LED Indicators 12V_LED1 MH14 MH15 Q866 EXP I2C4 Q872 EXP I2C0 MH13 Q871 LED Testing Only MH16 Q870 ACTLED 12V_LED1 5V_LED2 P_UART Q873 S_SDB BC29 BC57 Q867 Q869 C177 BC10 12V_LED2 P_MDIO P_SDB MH17 S_MDIO C165 C107 OVERHEATFAIL1...
  • Page 75 Appendix C BPN-SAS3-846EL Backplane Specifications C-10 Rear Connectors and LED Indicators ACT5 ACT23 ACT17 ACT11 ACT23 FAIL5 FAIL23 FAIL17 FAIL11 SAS #11 SAS #5 SAS #23 SAS #17 ACT4 ACT22 ACT16 ACT10 FAIL4 FAIL22 FAIL16 FAIL10 SAS #10 SAS #4 SAS #22 SAS #16 ACT3...
  • Page 76 SC847E1C/2C JBOD Chassis Manual Rear LED Indicators Rear LED Hard Drive Activity Failure LED SAS #0 ACT0 FAIL0 SAS #1 ACT1 FAIL1 SAS #2 ACT 2 FAIL2 SAS #3 ACT3 FAIL3 SAS #4 ACT4 FAIL4 SAS #5 ACT5 FAIL5 SAS #6 ACT6 FAIL6 SAS #7...
  • Page 77 Appendix C: BPN-SAS3-846EL Backplane Specifications C-11 Single and Dual Port Expanders SAS primary connectors J49 to J50 and secondary connectors J51 to J52 are bidirectional and can be treated as input or output. Single Ports BPN-SAS3-846EL1 backplanes have a single port expander that accesses all of the drives and supports cascading.
  • Page 78 SC847E1C/2C JBOD Chassis Manual C-12 Failover The BPN-SAS3-846EL2 model backplane has two expanders which enable effec- tive failover and recovery. Single Host Bus Adapter In a single host bus configuration, the backplane connects to one host bus adapter. SAS HBA MH14 MH15 Q866...
  • Page 79 Appendix C: BPN-SAS3-846EL Backplane Specifications C-13 Failover with RAID Cards and Multiple HBAs The BPN-SAS3-846EL backplane may be configured for failover with multiple HBAs using either RAID controllers or HBAs to acheive failover protection. RAID Controllers: If RAID controllers are used, then the failover is accomplished through port failover on the same RAID card.
  • Page 80 SC847E1C/2C JBOD Chassis Manual C-14 Connecting HBAs to the Backplane Connecting an Internal HBA to the Backplane The following section lists the most common cables used to connect the HBA to the backplane. MH14 MH15 Q866 EXP I2C4 MH13 Q872 MH16 EXP I2C0 Q871...
  • Page 81 Appendix C: BPN-SAS3-846EL Backplane Specifications Cable Name: Internal iPass (Mini-SAS) to HD (Mini-SAS) Part #: CBL-SAST-0508-01 Length: 50 cm (19 inches) Part #: CBL-SAST-0507-01 Length: 80 cm (31 inches) Description: This cable has an iPass (SFF-8087/Mini-SAS) connector (36-pin) at one end and a Mini-SAS HD (SFF-8643) connector at the other end.
  • Page 82 SC847E1C/2C JBOD Chassis Manual Connecting an External HBA to the Backplane This backplane supports external host bus adapters. In this configuration, the HBA and the backplane are in different physical chassis. This allows a JBOD (Just a Bunch Of Drives) configuration from an existing system. Single External Host Bus Adapter MH14 Q866...
  • Page 83 Appendix C: BPN-SAS3-846EL Backplane Specifications Connecting Multiple Backplanes in a Single Channel Environment This section describes the cables used when cascading from a single HBA. These connections use CBL-SAST-0531 internal cables and CBL-SAST-0573 external cables. CBL-SAST-0531 (Internal Cable) MH14 MH15 Q866 EXP I2C4 Q872...
  • Page 84 SC847E1C/2C JBOD Chassis Manual Single HBA Configuration Cables Figure C-15: External Mini-SAS HD to External Mini-SAS HD Cable Cable Name: 1 Meter External Mini-SAS HD to External Mini-SAS HD Cable Part #: CBL-SAST-0573 Ports: Single Placement: External Cable Description: External cascading cable, connects ports between servers and JBODs. Figure C-16: Mini-SAS HD Internal to External Adapter Cable Name: 16-port Mini-SAS HD Internal to External Cable Adapter with LP Bracket...
  • Page 85 Appendix C: BPN-SAS3-846EL Backplane Specifications Connecting Multiple Backplanes in a Dual Channel Environment This section describes the cables used when cascading from dual HBAs. These con- nections use CBL-SAST-0531 internal cables and CBL-SAST-0573 external cables. MH14 MH15 Q866 EXP I2C4 MH13 Q872 MH16...
  • Page 86 SC847E1C/2C JBOD Chassis Manual Cascading BPN-SAS3-846EL and BPN-SAS3-847EL This section describes the cables used when cascading with the BPN-SAS3-846EL and BPN-SAS3-847EL backplanes together. MH14 MH15 Q866 EXP I2C4 MH13 Q872 EXP I2C0 Q871 Q870 LED Testing Only MH16 12V_LED1 ACTLED P_UART Q873 S_SDB...

  • Page 87: Appendix D Bpn-Sas3-847El Backplane Specifications

    Appendix D: BPN-SAS3-847EL Backplane Specifications Appendix D BPN-SAS3-847EL Backplane Specifications To avoid personal injury and property damage, carefully follow all the safety steps listed below when accessing your system or handling the components. D-1 ESD Safety Guidelines Electrostatic Discharge (ESD) can damage electronic com ponents. To prevent dam- age to your system, it is important to handle it very carefully.
  • Page 88 This manual reflects BPN-SAS3-847EL Revision 1.00, the most current release available at the time of publication. Always refer to the Supermicro Web site at www.supermicro.com for the latest updates, compatible parts and supported con- figurations.
  • Page 89 Appendix D: BPN-SAS3-847EL Backplane Specifications D-6 Front Connectors P_ICE C102 TP31 EC14 P_JTAG 1 2 3 EC20 MH11 MH15 MH17 BPN-SAS3-847EL2 TP30 MH13 REV:1.00 PRI_J3 P_HB_LED DESIGNED IN USA EC19 EC13 MH16 MH12 MH14 PRI_WWN P_UART PRI_J2 P_SDB C108 P_MDIO EC16 EC24 PRI_J1...
  • Page 90 SC847E1C/2C JBOD Chassis Manual D-7 Front Connector and Pin Definitions 1. - 2. Primary and Secondary Expander Chips The primary and secondary expander chips allow the backplane to support dual port, cas- cading, and failover configurations. 3. Backplane Power Connectors Backplane Main Power The 4-pin connectors, designated PWR1 -...
  • Page 91 Appendix D: BPN-SAS3-847EL Backplane Specifications 11. SMB Connector The SMB connector. is designated SMB (J28). 12. - 13. JTAG Connectors The Primary JTAG connector is designated P_JTAG (J25). The secondary JTAG connec- tor is designated S_JTAG (J35) and is not present on BPN-SAS3-847EL1 backplanes.
  • Page 92 SC847E1C/2C JBOD Chassis Manual D-8 Front Jumper Location and Settings P_ICE C102 TP31 EC14 P_JTAG 1 2 3 EC20 MH11 MH15 MH17 ACTLED1 BPN-SAS3-847EL2 TP30 MH13 REV:1.00 PRI_J3 DESIGNED IN USA P_HB_LED EC19 EC13 OVERHEATFAIL1 MH16 MH12 MH14 PRI_WWN P_UART PRI_J2 P_SDB C108...
  • Page 93 Appendix D: BPN-SAS3-847EL Backplane Specifications D-9 Front LED Indicators P_HB_LED 5V_LED1 12V_LED1 P_ICE C102 TP31 EC14 P_JTAG 1 2 3 EC20 MH11 MH15 MH17 BPN-SAS3-847EL2 TP30 MH13 REV:1.00 PRI_J3 DESIGNED IN USA P_HB_LED EC19 EC13 OVERHEATFAIL2 MH16 MH12 MH14 PRI_WWN P_UART PRI_J2 P_SDB...
  • Page 94 SC847E1C/2C JBOD Chassis Manual D-10 Rear Connectors and LED Indicators ACT13 ACT7 ACT19 FAIL13 ACT13 ACT19 FAIL7 FAIL19 SAS #13 SAS #19 SAS #7 FAIL9 FAIL13 ACT12 ACT6 ACT18 ACT18 FAIL12 ACT12 FAIL6 FAIL18 SAS #6 SAS #12 SAS #18 FAIL12 FAIL8 ACT5...
  • Page 95 Appendix D: BPN-SAS3-847EL Backplane Specifications Rear LED Indicators Rear LED Hard Drive Activity Failure LED SAS #0 ACT0 FAIL0 SAS #1 ACT1 FAIL1 SAS #2 ACT 2 FAIL2 SAS #3 ACT3 FAIL3 SAS #4 ACT4 FAIL4 SAS #5 ACT5 FAIL5 SAS #6 ACT6 FAIL6...
  • Page 96 SC847E1C/2C JBOD Chassis Manual Notes D-10...
  • Page 97 Appendix D: BPN-SAS3-847EL Backplane Specifications D-11 Single and Dual Port Expanders SAS connectors PRI-J1 to J4 and SEC-J1 to J4 are bidirectional and can be treated as input or output. Single Ports BPN-SAS3-847EL1 backplanes have a single port expander that accesses all of the drives and supports cascading.
  • Page 98 SC847E1C/2C JBOD Chassis Manual D-12 Failover The BPN-SAS3-847EL2 model backplane has two expanders which enable effec- tive failover and recovery. Single Host Bus Adapter In a single host bus configuration, the backplane connects to one host bus adapter. SAS HBA Port A Expander 1 C102 TP31...
  • Page 99 Appendix D: BPN-SAS3-847EL Backplane Specifications D-13 Failover with RAID Cards and Multiple HBAs The BPN-SAS3-847EL backplane may be configured for failover with multiple HBAs using either RAID controllers or HBAs to acheive failover protection. RAID Controllers: If RAID controllers are used, then the failover is accomplished through port failover on the same RAID card.
  • Page 100 SC847E1C/2C JBOD Chassis Manual D-14 Connecting HBAs to the Backplane Connecting an Internal HBA to the Backplane The following section lists the most common cables used to connect the HBA to the backplane. C102 TP31 P_ICE EC14 P_JTAG 1 2 3 EC20 MH11 MH15...
  • Page 101 Appendix D: BPN-SAS3-847EL Backplane Specifications Cable Name: Internal iPass (Mini-SAS) to HD (Mini-SAS) Part #: CBL-SAST-0508-01 Length: 50 cm (19 inches) Part #: CBL-SAST-0507-01 Length: 80 cm (31 inches) Description: This cable has an iPass (SFF-8087/Mini-SAS) connector (36-pin) at one end and a Mini-SAS HD (SFF-8643) connector at the other end.
  • Page 102 SC847E1C/2C JBOD Chassis Manual Connecting an External HBA to the Backplane This backplane supports external host bus adapters. In this configuration, the HBA and the backplane are in different physical chassis. This allows a JBOD (Just a Bunch Of Drives) configuration from an existing system. Single External Host Bus Adapter P_ICE C102...
  • Page 103 Appendix D: BPN-SAS3-847EL Backplane Specifications Connecting Multiple Backplanes in a Single Channel Environment This section describes the cables used when cascading from a single HBA. These connections use CBL-SAST-0531 internal cables and CBL-SAST-0573 external cables. CBL-SAST-0531 (Internal Cable) P_ICE C102 TP31 EC14 P_JTAG...
  • Page 104 SC847E1C/2C JBOD Chassis Manual Single HBA Configuration Cables Figure D-16: External Mini-SAS HD to External Mini-SAS HD Cable Cable Name: 1 Meter External Mini-SAS HD to External Mini-SAS HD Cable Part #: CBL-SAST-0573 Ports: Single Placement: External Cable Description: External cascading cable, connects ports between servers and JBODs. Figure D-17: Mini-SAS HD Internal to External Adapter Cable Name: 16-port Mini-SAS HD Internal to External Cable Adapter with LP Bracket...
  • Page 105 Appendix D: BPN-SAS3-847EL Backplane Specifications Connecting Multiple Backplanes in a Dual Channel Environment P_ICE C102 TP31 EC14 P_JTAG 1 2 3 EC20 MH11 MH15 MH17 BPN-SAS3-847EL2 TP30 MH13 REV:1.00 Port A Expander 1 PRI_J3 DESIGNED IN USA P_HB_LED EC19 EC13 MH16 MH12 MH14...
  • Page 106 SC847E1C/2C JBOD Chassis Manual Cascading BPN-SAS3-846EL and BPN-SAS3-847EL For instructions on cascading BPN-SAS3-846EL and BPN-SAS3-847EL see page C-18 of this manual. D-20...

  • Page 107: Appendix E Cse-Ptjbod-Cb3 Power Board Specifications

    Appendix E: CSE-PTJBOD-CB3 Power Board Specifications Appendix E CSE-PTJBOD-CB3 Power Board Specifications To avoid personal injury and property damage, carefully follow all the safety steps listed below when accessing your system or handling the components. ESD Safety Guidelines Electrostatic Discharge (ESD) can damage electronic com ponents. To prevent damage to your system, it is important to handle the backplane very carefully.
  • Page 108 This manual reflects the CSE-PTJBOD-CB3 Revision 1.02 power board, the most current release available at the time of publication. Always refer to the Supermicro web site at www.supermicro.com for the latest updates, compatible parts and sup- ported configurations.
  • Page 109 Appendix E: CSE-PTJBOD-CB3 Power Board Specifications Components and Connectors FAN4 FAN2 FAN5 FAN6 FAN3 FAN10 FAN9 JPW1 1-2:SAS3 2-3:SAS2_847D NMI X PWR LED X NIC1 X OH/FF X RST ON PWR ON Figure E-1: Components and Connectors on the CSE-PTJBOD-CB3 Components and Connectors 6.
  • Page 110 SAS2/SAS3 backplanes. 3. Manufacturing Test Connector This connector is designated J3 and is for Supermicro manufacturing use only. 4. Manufacturer's USB Test Connector This connector is designated FB1 and is for Supermicro manufacturing use only.
  • Page 111 Appendix E: CSE-PTJBOD-CB3 Power Board Specifications 6. IPMI LAN Connector The Intelligent Platform Management Inter- face (IPMI) LAN connector is designated J8 and supports connectivity with a local network using cable CBL-NTWK-0584 or CBL-NTWK-0587. 7. SC847D SAS2 I2C Connectors The backplane connectors are designated J4-J7 and allow the power board to be con- nected to up to four SC847D expanders.
  • Page 112 SC847E1C/2C JBOD Chassis Manual Connectors Jumpers and LED Indicators SAS2/SAS3: Use JP1-JP4 FAN4 FAN2 FAN3 FAN5 FAN6 FAN10 FAN9 JPW1 1-2:SAS3 2-3:SAS2_847D NMI X PWR LED X NIC1 X OH/FF X RST ON PWR ON SC847D: Use J4-J7 Figure E-2: CSE-PTJBOD-CB3 Connectors and Jumpers Front SAS2/SAS3 and SC847D Jumpers Jumper Description...
  • Page 113 Appendix E: CSE-PTJBOD-CB3 Power Board Specifications FAN2 FAN4 FAN5 FAN6 FAN3 FAN10 FAN9 JPW1 1-2:SAS3 2-3:SAS2_847D NMI X PWR LED X NIC1 X OH/FF X RST ON PWR ON Figure E-3: CSE-PTJBOD-CB3 LED Indicators LED Indicators Description Heartbeat LED: A blinking LED indicates BMC activity Power LED: DC power indicator...
  • Page 114 SC847E1C/2C JBOD Chassis Manual Notes...
  • Page 115 Appendix E: CSE-PTJBOD-CB3 Power Board Specifications SC847D JBOD Cabling E16 I C Cabling Use the following diagram to connect the CSE-PTJBOD-CB3 to the front and rear backplanes in SC847D JBOD E16 model chassis. Jumper Settings Jumper Setting Pins 1-2: SAS3 enabled Pins 2-3: SAS2 enabled and SC847 When enabling SAS2/SAS3 functionality, use connectors JP1-JP4, (see Page 2-4) and set the JP5 jumper to pins 1-2 (SAS3) or pins 3-4 (SAS2).
  • Page 116 SC847E1C/2C JBOD Chassis Manual E26 I C Cabling Use the following diagram to connect the CSE-PTJBOD-CB3 to the front and rear backplanes in SC847D-JBOD-E26 model chassis. Front Secondary Expander Front Primary Expander BPN-EXP-847DF3EL1 BPN-EXP-847DF3EL1 CBL-0157L CBL-0157L-01 CBL-0157L-01 CBL-0157L-01 CSE-PTJBOD-CB3 Rear Primary Expander Rear Secondary Expander BPN-EXP-847DF3EL1 BPN-EXP-847DF3EL1...
  • Page 117 Appendix E: CSE-PTJBOD-CB3 Power Board Specifications SC847 JBOD Cabling SAS3 I C Cabling in the SC847 JBOD Chassis Use the diagram below to connect the CSE-PTJBOD-CB3 to the front and rear backplanes in the SC847 JBOD chassis. Jumper Settings Jumper Setting Pins 1-2: SAS3 enabled Pins 2-3: SAS2 enabled and SC847D...
  • Page 118 SC847E1C/2C JBOD Chassis Manual E-10 SC847 Cabling SAS3 I C Cabling in the SC847B Chassis Use the diagram below to connect the I C cabling. Ensure that the JP5 jumper on the CSE-PTJBOD-CB3 is cabled correctly according to the table below. Jumper Settings Jumper Setting...
  • Page 119 Appendix E: CSE-PTJBOD-CB3 Power Board Specifications E-11 SC417B Cabling SAS3 I C Cabling in the SC417B Chassis Use the diagram below to connect the I C cabling. Ensure that the JP5 jumper on the CSE-PTJBOD-CB3 is cabled correctly according to the table below. Jumper Settings Jumper Setting...
  • Page 120 SC847E1C/2C JBOD Chassis Manual Notes E-14...
  • Page 121 Appendix E: CSE-PTJBOD Power Board Specifications E-12 System Details Overview This chapter provides information on system components which are directly affected by the CSE-PTJBOD-CB3 power board. Topics covered are the control panel, power up and power down sequences and IPMI. E-13 Control Panel Control Panel Buttons There are two push-buttons located on the left handle of the chassis.
  • Page 122 SC847E1C/2C JBOD Chassis Manual E-14 Control Panel LEDs The control panel is located on the left handle of the SC847DJ chassis and has five LEDs. These LEDs provide you with critical information related to different parts of the system. This section explains what each LED indicates when illuminated and any corrective action you may need to take.
  • Page 123 Appendix E: CSE-PTJBOD Power Board Specifications Power Failure: When this LED flashes, it indicates a failure in the redundant power supply. E-17...
  • Page 124 SC847E1C/2C JBOD Chassis Manual E-15 JBOD Power Up/Power Down Sequences Power Up Sequences First Use or Power Cord Plug-In 1. Plug the power cords into the rear of the power supplies 2. Wait until blue Information LED starts to blink 3.
  • Page 125 E-16 CSE-PTJBOD-CB3 IPMI Static IP to DHCP Setting IP Address to DHCP Setting 1. Download the utility from the Supermicro website or technical support 2. Extract the file to a known folder. 3. By default, the CSE-PTJBOD-CB3 will be configured in static IP 192.168.1.99 4.
  • Page 126 SC847E1C/2C JBOD Chassis Manual E-18 CSE-PTJBOD-CB3 Power Card For information on installing the CSE-PTJBOD-CB3 power card into the chassis, see Section 4-7 Installing the Power Card. E-20...
  • Page 127 Appendix E: CSE-PTJBOD Power Board Specifications Notes E-21...
  • Page 128 SC847E1C/2C JBOD Chassis Manual Disclaimer (cont.) The products sold by Supermicro are not intended for and will not be used in life sup- port systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to per- form be reasonably expected to result in significant injury or loss of life or catastrophic property damage.

This manual is also suitable for:

Sc847e2c seriesSc847e1c-r1k28jbodSc847e2c-r1k28jbod

Table of Contents